Manuals / Toshiba / Computer Equipment / Printer

Toshiba GA-1040 manual Setting Up The Appletalk, Preparation

Models: GA-1040

1 130

Download 130 pages 15.87 Kb

Page 48

SETTING UP THE APPLETALK

SETTING UP THE APPLETALK

: The PostScript option, PS3 Upgrade (GE-1020) or PS3 & HDD Upgrade (GE-1030), is required for printing from a Macintosh computer.

When you print from a Macintosh computer using the printer, you should enable the AppleTalk.

PREPARATION:

Before setting up the AppleTalk, please make sure the following:

•The TCP/IP has been configured to enable the TopAccess.

You can set up the AppleTalk using TopAccess or the Control Panel on the printer.

•Some settings cannot be operated from the Control Panel. When you want set items for further particulars, set up from TopAccess.

P47 “Setting up from TopAccess”

•When you do not have the TCP/IP network to use TopAccess, set up from the Control Panel on the printer.

P49 “Setting up from Control Panel”

NOTE:

The AppleTalk has already been enabled as a factory default. Operate the settings only when you want to set an AppleTalk zone that the printer belongs or AppleTalk is currently disabled. When you want to set an AppleTalk zone, you must set using TopAccess.

46

Image 48

Toshiba GA-1040 manual Setting Up The Appletalk, Preparation

Contents

Page FCC NOTICE For European models onlyPage TABLE OF CONTENTS SETUP FLOWCONNECTING TO THE PRINTER SETTING UP THE PROTOCOLSINSTALLING THE PRINTER DRIVER APPENDIXAppleTalk Setting Other SettingSETUP FLOW SETUP FLOWSETUP FLOW Setup Flow for WindowsFor Parallel Printing For SMB PrintingFor LPR Printing For IPP PrintingConfiguring the Options Connecting the GA-1040For Novell Printing Preparing to use the TopAccessInstalling the Printer Driver Configuring the OptionsSetup Flow for Macintosh Connecting the GA-1040Preparing to use the TopAccess Setting up the ProtocolPage CONNECTING TO THE PRINTER CONNECTING THE PRINTERCONNECTING TO THE PARALLEL PORT Turn OFF the power of the printer and the power of the computerPREPARATION SUPPLEMENTCONNECTING TO THE NETWORK 1 Turn OFF the power of the printer2 Insert the 10BASE-T or 100BASE-TX cable in the connector CONNECTING THE PRINTERPage PREPARING TO USE THE TOPACCESS TOPACCESSPREPARING TO USE THE SETTING UP THE TCP/IP Assigning the TCP/IP using the DHCP, RARP, or BOOTP serverAssigning the TCP/IP manually SUPPLEMENTAssigning the TCP/IP Settings Automatically PREPARING TO USE THE TOPACCESS1 Press on the Control Panel 2 Press ON/OFF 3 Press OFF LINEPress SETTING and press ADMIN Press PROTOCOL SETUP Press TCP/IPPress SET to save the settings 7 Press ETHERNET10 Press GATEWAY Press ENABLE for “Enable Auto IP” and press SET Press UTILITY and press FUNCTION Press RESET14 Press OK to reset the printer PREPARING TO USE THE TOPACCESS15 Wait for a few minutes until the printer completes initializing Assigning the TCP/IP Settings Manually 1 Presson the Operation Panel 2 Press ON/OFF 3 Press OFF LINEPress SETTING and press ADMIN Press PROTOCOL SETUP Press TCP/IPPREPARING TO USE THE TOPACCESS Press ETHERNET Press DISABLE for “Enable Auto IP” and press Next Enter the IP address using numeric keysTo move the cursor, press or You cannot enter any number exceeding “0.0.0.0” cannot be assigned to the IP address11 Press SET to save the settings 14 Press SET to save the settings10 Press SUBNET MASK and enter the Subnet Mask if required 12 Press GATEWAYPress UTILITY and press FUNCTION Press RESET 17 Press OK to reset the printerTOPACCESS 18 Wait for a few minutes until the printer completes initializingPREPARING TO USE THE STARTING TOPACCESS Starting TopAccess3 The TopAccess screen appears SUPPLEMENTSDescription of Screen Loging on to the Administrator’s Page Start the TopAccessClick on the Administrator menu Enter the password and click on OK4 The Administrator Page is displayed TOPACCESSPREPARING TO USE THE Page SETTING UP THE PROTOCOLS SETTING UP THE PROTOCOLSSETTING UP THE IPX/SPX AND NETWARE PREPARATIONSSetting up from TopAccess 1 Start the TopAccess and log in to the Administrator’s page2 Click on the Network SETUP menu and click on the IPX/SPX tab 3 Select the frame type to be used and click on SETUPClick on the NetWare tab Enable Bindery Server 10 Click on Printer Reset The Printer Reset page is displayed12 Wait for a few minutes until the printer completes initializing The confirmation screen appearsSetting up from Control Panel SETTING UP THE PROTOCOLSPress on the Control Panel Press ON/OFF Press OFF LINEPress SETTING and press ADMIN Press PROTOCOL SETUP Press IPX/SPXSUPPLEMENT Make sure AUTO is selected and press SET Press NETWARE10 Press ENABLE for “Enable NDS” and press Next 11 Enter the value for each item and press SETSUPPLEMENT 12 Press ENABLE for “Enable NDS” and “Enable Bindery Server” and press Next twice13 Enter the value for each item and press SET Press UTILITY and press FUNCTION Press RESET 16 Press OK to reset the printerSETTING UP THE PROTOCOLS 17 Wait for a few minutes until the printer completes initializingSETTING UP THE APPLETALK PREPARATIONSetting up from TopAccess Start the TopAccess and log in to the Administrator’s pageClick on the Network SETUP menu and click on the AppleTalk tab Check the checkbox for “Enable AppleTalk” and click on SETUPClick on the Other menu and click on the Reset tab Click on Printer ResetClick on OK to reset the printer The Printer Reset page is displayedSetting up from Control Panel SETTING UP THE PROTOCOLSPress on the Control Panel Press ON/OFF Press OFF LINEPress SETTING and press ADMIN Press PROTOCOL SETUP Press APPLETALKPress ENABLE for “Enable AppleTalk” and press SET Press UTILITY and press FUNCTION Press RESETSETTING UP THE PROTOCOLS The screen returns to the PROTOCOL menu10 Press OK to reset the printer 11 Wait for a few minutes until the printer completes initializingSETTING UP THE PRINT SERVICE SETTING UP THE PRINT SERVICESETTING UP THE WINDOWS PRINTING 1 Start the TopAccess and log in to the Administrator’s pageClick on the Network SETUP menu and click on the Other tab Enter each item and click on SETUPClick on the Other menu and click on the Reset tab Click on Printer ResetComment Click on OK to reset the printer Wait for a few minutes until the printer completes initializingSETTING UP THE LPD PRINTING 1 Start the TopAccess and log in to the Administrator’s pageClick on the Network SETUP menu and click on the Other tab Enter each item and click on SETUPClick on the Other menu and click on the Reset tab Click on Printer Reset9100 Queue Click on OK to reset the printer SETTING UP THE PRINT SERVICEWait for a few minutes until the printer completes initializing Page INSTALLING THE PRINTER DRIVER INSTALLING THEPRINTER DRIVER ABOUT INSTALLATION Software ComponentsSystem Requirements For WindowsAbout Installation Procedure Local Connection for WindowsSMB Printing for Windows LPR Printing for WindowsInstalling the Printer Driver for Parallel Printing INSTALLING THE PRINTER DRIVER WindowsPREPARATION REQUIREMENT6 Select the components to be installed and click on Next Check this to install the PCL6 printer driver. PostScript DriverCheck this to install the PostScript printer driver AFM Check this to install the Agfa Monotype Font ManagerSelect “LPT1” and click on Next Click on NextClick on Finish Start copying filesInstalling the Printer Driver for SMB Printing PREPARATIONSSUPPLEMENT Windows 95/98/Me 2 Click on Yes3 Select whether printing MS-DOS-based programs and click on Next Click on Have Disk5 Click on Browse 6 Insert the CD-ROM into the CD-ROM driveClick on OK 13 The printer driver is installed and the print queue screen appears INSTALLING THE PRINTER DRIVER11 Select “Yes” to print a test page and click on Finish Windows NT 4.0/2000/XP 1 Click on Start and select Printers in SettingsREQUIREMENT Click on File and select Server PropertiesINSTALLING THE Click on the Ports tab and click on Add PortSelect “Local Port” and click on New Port The Printer Ports screen appears6 Click on Cancel to close the screen The installer automatically starts and the Welcome INSTALLING THE PRINTER DRIVERClick on OK to close the screen Insert the CD-ROM into the CD-ROM drive13 Select the components to be installed and click on Next Check this to install the PCL6 printer driver. PostScript DriverCheck this to install the PostScript printer driver AFM Check this to install the Agfa Monotype Font Manager14 Select the port that you create and click on Next 15 Click on Next16 Click on Finish Installing the Printer Driver for LPR Printing PREPARATIONSWindows NT 1 Click on Start and select Printers in SettingsREQUIREMENTS Click on the Ports tab and click on Add Port Select “LPR Port” and click on New PortSUPPLEMENT 6 Click on Cancel to close the screen Click on OK to close the screen Insert the CD-ROM into the CD-ROM driveSUPPLEMENT 9 Click on Next13 Select the components to be installed and click on Next Check this to install the PCL6 printer driver. PostScript DriverCheck this to install the PostScript printer driver AFM Check this to install the Agfa Monotype Font ManagerPage Windows 2000/XP 1 Click on Start and select Printers in SettingsREQUIREMENTS Click on the Ports tab and click on Add Port Select “Standard TCP/IP Port” and click on New PortClick on Next The Printer Ports screen appearsSelect “Custom” and click on Settings 11 Click on Close 10 The screen returns to the Printer Ports screenThe screen returns to the Print Server Properties screen INSTALLING THE PRINTER DRIVER 12 Click on OK to close the screen13 Insert the CD-ROM into the CD-ROM drive SUPPLEMENT18 Select the components to be installed and click on Next Check this to install the PCL6 printer driver. PostScript DriverCheck this to install the PostScript printer driver AFM Check this to install the Agfa Monotype Font Manager19 Select the LPR Port that you create and click on Next 20 Click on Next21 Click on Finish Installing the Printer Driver for IPP Printing 1 Click on Start and select Printers in SettingsPREPARATIONS SUPPLEMENTINSTALLING THE PRINTER DRIVER Double-click on the Add Printers iconClick on Next Select “Network printer” and click on Next The Add Printer Wizard screen appearsClick on OK Click on Have Disk 8 Click on Browse 10 Click on OK 11 Select the printer driver that compatible toyour GA-1040 printer and click on OK 12 The printer driver is installed on Windows 2000/XP P109 “Configuring the Options”Installing the Printer Driver for Novell Printing PREPARATIONSSUPPLEMENT Windows 95/98/Me REQUIREMENTSSUPPLEMENT Click on YesSelect whether printing MS-DOS-based programs and click on Next Click on Have Disk5 Click on Browse Click on OK11 Select “Yes” to print a test page and click on Finish PRINTER DRIVER13 The printer driver is installed and the print queue screen appears Windows NT 4.0/2000/XP REQUIREMENTSSUPPLEMENT 3 Clcik on OK4 Click on Have Disk 5 Click on Browse8 Click on OK 10 The printer driver is installed and the print queue screen appears Installing the Agfa Monotype Font Manager SUPPLEMENT1 Click on Next 2 Click on NextThe Setup Complete screen appears Click on OKClick on Finish Select “Yes, I want to restart my computer now”, and click on FinishConfiguring the Options Windows 95/98/Me2 Click on the Options tab and set the options Pedestal This sets whether or not the pedestal is installed 3 Click on OK to save settingsSUPPLEMENT Windows NT 4.0/2000/XP PCL6 Printer Driver2 Click on the Options tab and set the options 3 Click on OK to save settings SUPPLEMENT2 Click on the Device Settings tab and set the options PostScript Printer Driver3 Click on OK to save settings Installing the Printer Driver to Macintosh Installing the AdobePSINSTALLING THE PRINTER DRIVER Macintosh SUPPLEMENT3 Click on Yes 4 Click on Replace 5 Click on OK 6 Click on RestartCreating the AdobePS Printer Click on apple menu and select Chooser5 Close the screen INSTALLING THE 6 Click on OKPRINTER DRIVER Page APPENDIX APPENDIXDEFAULT SETTING LIST Default Setting List for Printer FunctionTopAccess Setting TopAccess SetupPrinter Setting Printer SetupPCL Setup Default Setting List for Network Function Port SettingTCP/IP Setting IPX/SPX SettingNetWare Setting BinderyAppleTalk Setting Other SettingWindows Printing Service LPD Printing ServicePage Copyright TOSHIBA TEC CORPORATION 2002 ALL RIGHTS RESERVED 6LA50221000 R01112004801 TG