Mounting the Keypads | VistaQuest N7227V5 instruction

KEYPAD CONNECTOR CABLE

↓

4

5

BLACK

RED

GREENKEYPADS

6

7YELLOW

CONTROL

TERMINALS

Figure 5. Keypad Connections To The Control Board

Mounting the Keypads

1.Make sure addressable type keypads (4137AD, 5137AD, 6128, 6137, 6138, and 6139) are set to non-addressable mode (address 31), which is the factory default setting. Refer to the instructions provided with the keypad for address setting procedure.

2.Mount the keypads at a height that is convenient for the user. Refer to the instructions provided with the keypad for mounting procedure.

You can either surface mount or flush mount keypads (using an appropriate Trim Ring Kit: 5137TRK or 6139TRK). Refer to the mounting instructions and template included with the keypad and/or trim ring kit for specific information.

Using a Supplementary Power Supply to Power Additional Keypads

The control provides 500mA for powering keypads (up to a maximum of 4 ) and other devices from the auxiliary power output. The backup battery will supply power to these keypads in the event that AC power is lost.

When the control’s auxiliary power load for all devices exceeds 500mA, you can power additional keypads from a regulated, 12VDC power supply (e.g., 487-12 supplies 12V, 250mA; 488-12 supplies 12V, 500mA). Use a UL Listed, battery-backed supply for UL installations.

The 487-12/488-12 power supplies have a backup battery which can power these keypads in the event of AC power loss.

Keypads powered from supplies which do not have a backup battery will not function when AC power is lost. Therefore, be sure to power at least one keypad from the Control's auxiliary power output.

Connect the additional keypads as shown in Figure 6, using the keypad wire colors shown. Be sure to observe the current ratings for the power supply used.

Make connections directly to the screw terminals as shown in Figure 6. Make no connection to the keypad blue wire (if present).

Be sure to connect the negative (–) terminal on the Power Supply unit to terminal 4 (AUX – ) on the control.

– 16 –

Image 16

VistaQuest N7227V5 installation instructions Mounting the Keypads, Keypad Connections To The Control Board

Contents

VISTA-10SE Recommendations For Smoke And Heat Detectors Recommendations For Proper Intrusion Protection Table of Contents Relay Output Devices Sequential Mode For 5800 Series Wireless Transmitters Section List of Figures HOW to USE this Manual Conventions Used in this Manual Wireless Expansion General Description AC Power Supply Back-Up BatteryOptional Phone module Supports the Ademco 4285 Phone module Communication Formats Installing the Lock if used Installing the ControlMounting the Cabinet Relay Unit if installed in cabinet Standard Phone Line Connections Standard Telephone Line Connections Wiring The AC Transformer Installing The Back-Up BatteryWiring Table Do not Connect the Wires to the Battery YET Wiring To The Keypads Installing Remote KeypadsKeypads That May Be Used Mounting the Keypads Keypad Connections To The Control Board Preliminary Check-out Procedure Using a Supplementary Power Supply For Keypads Basic HARD-WIRED Zones Installing the Hard-Wired ZonesWiring Burglary and Panic Devices To Zones Wiring 4-Wire Smoke/Combustion Detectors on Zone Programming Hard-Wired Zones Zone Types Special Notes on Zone Check-Out Procedure For Hard-Wired ZonesProgramming Wireless RF Zone Expansion 5800 RF Systems Wireless Systems AvailableSeries Receiver Wireless Zones Wireless System Operation and Transmitter Supervision Transmitter Battery Life Wireless System Installation AdvisoriesInstallation and Setup of the 4281/5881 Wireless Receivers Receiver Supervision Series Transmitter Setup Board Setting the DIP Switches On 5700 SeriesRefer to the Compatible 5700 Series Transmitters DIP Switch Tables for 5700 RF System Wireless Devices Compatible 5700 Series Transmitters Model Product Zone/ID # Description Programming the Control For a 5700 Wireless System Using the House ID Sniffer Mode 5700 SystemsEnter your Installer Code + # + Zone Programming For 5700 Transmitters Programming Guide Programming 5700 RF Enter the Installer Code + # +Systems Series Transmitter Setup Compatible 5800 Series Transmitters Temp Programming the RF Transmitters 5800 RF Systems GBD Enrolling 5800 Transmitters Into The System RF House ID CodeEnrolling Through Zone Programming ZN ZT RC In L 0 0 0 0 RF Recommend that you confirm the programming of every Transmitter before proceeding to the next zone Sniffer Mode Check-Out Procedure for Wireless ZonesTransmitter ID Go/No Go Test Relay Device Basics Relay Output DevicesRelay Modules Alarm Programming Output Relays Choices for Zone Types Example of Output Relay Programming Installing the Phone module Phone Module WiringPhone Module General Information Terminal Connects to Caller ID Units Wiring Notes 4285 Programming The Control For Phone Access Press 95. Ring Detection CountVoice Answering Module Downloading Field 95 Programming To Check Phone module Operation From an On-Premises Phone Checking the Operation of the 4285 Phone moduleTo Check Phone module Operation From an Off-Premises Phone External Sounders Press 30. Alarm Bell Timeout Testing the SounderSounder Connections Press 51. Confirmation of Arming Ding General Information Long Range RadioConnection Wiring Connections Audio Alarm Verification AAVProgramming Connection Of AAV Unit When Not Using a 4285 Phone module Final Power UP To bypass this delay, press # +Calculating the Battery Size Needed Example Making the Battery ConnectionsDevice Current # Units Total Current Total = Entering Zone Descriptors program menu mode SectionProgramming the Descriptors Press O R Press 8 to save all words in memory Press 6 to accept the selected wordAlternate Method For Programming Zone Descriptors Method Alpha Vocabulary List For Adding Custom Words Sequential Mode For 5800 Series Wireless Transmitters Serial # ↑ Page System Communication Following describes each format in greater detail Ademco Contact ID Reporting takes the following format +1/4+1 Report Standard Expanded Communication Programming Table of Contact ID Event Codes Press 45 Phone System Select Enter 1 digit default = Press 46 Report FORMAT, PRIMARY/SECONDARYPress 47 SPLIT/DUAL Reporting To Primary Phone No To Secondary Phone No To Program System Status and Restore Report Codes 60 68, 70 Press 60 Trouble Report CodePress 61 Bypass Report Code Press 62 AC Loss Report Code Press65 OPEN/EXIT Alarm Report CODE, 1st Digits Press 67 RF XMTR. LOW Battery Report CodePress 68 Cancel Report Code Press 70 Alarm Restore Report CODE, 1st Digit Press 74 LOW BAT Restore Report Code Press 75 RF XMTR. LOW Battery Restore CodePress 92 Number of Reports in Armed Period Press 94 Download Phone Number Testing the System Test Procedure To the Installer System Operation To program a Duress codeTo change the Duress code To delete the Duress code Features for Each Arming Mode Keypad FunctionsDisarmed, Not Ready Forced Quick Bypass Keys Displayed as Zone If usedRelay Outputs Security Code + # + Trouble Conditions See Troubleshooting Guide also Troubleshooting Guide System including Wireless Control Before you call Technical Support, be sure you PleaseRead the Instructions Specifications & Accessories SpecificationsVISTA-10SE Security Control Remote Keypad Remote Keypads Relay Module Phone Module Transmitter ModuleZones With the Ademco VISTA-10SE Accessories Compatible Devices No CNAdemco 702 Outdoor Siren Federal Communications Commission FCC Part 15 Statement Federal Communications Commission FCC Part 68 Statement UL Notices Canadian Department of Communications DOC Statement Limitations of this Alarm System ADT VISTA-10SE Summary of Connections Ademco Limited Warranty