Accessories Compatible Devices, No CN, Siren | VistaQuest N7227V5

Accessories (Compatible Devices)

Sounders

No. 1321	16.5VAC, 25VA Plug-In Transformer (in U.S.A.)
No. 1321CN	16.5VAC, 25VA Plug-In Transformer (in Canada)

Ademco AB-12M 10”		Motor bell & box. UL Grade A. 100mA current
Motorized Bell & Box		draw.

Ademco 1011BE12M 10”		Motor bell & box. UL Listed. 100mA current
Motorized Bell & Box		draw.

Ademco 702 Outdoor		Self-contained 6–12 volt siren (driver built-in)
Siren		and weatherproof for outdoor use. Can be wired
		for either a steady or warble sound. 117dB @ 10
		feet. 1500mA current draw.

Ademco 719		Self-contained 6–12-volt siren (driver built in).
2-Channel Siren		Steady or warble sound. 109dB @ 10 feet.
		550mA current draw.

Ademco 747		Self-contained 6–15 volt siren (driver built-in) for
Indoor Siren		indoor wall mount. 747F available for flush
		mounting. 105dB @ 10 feet. 400mA current
		draw.

Ademco 747UL		Self-contained 6–15 volt siren (driver built-in) for
Indoor Siren		indoor wall mount. UL Listed. 85dB @ 10 feet.
		320mA current draw.

Ademco 744		6 jumper-selected sound outputs. Rated at
Siren Driver		119dB with use of an 8-ohm 30 watt speaker.
		1.3 amps current draw.

Ademco 745X3*

Voice Siren Driver

Ademco 705–820,

5-inch Round Speaker

Ademco 713 Speaker

12 volt voice siren driver with English, Spanish and French voice messages. Separate messages for Fire and Burglary. Use with 8 - ohm speaker. UL Listed. 1100mA current draw.

20-watt, 8-ohm indoor or outdoor speaker. Requires a driver.

40-watt, 8-ohm, indoor/outdoor speaker. Requires a driver.

Compatible 4-Wire

Smoke/Combustion

Detectors

System Sensor PA400B Indoor piezo sounder (red or beige), rated at 90

(beige)/PA400R (red) dB @ 10 feet.

Indoor Piezo Sounder

*Requires special power wiring connections.

System Sensor

1412	4-wire ionization products of combustion detector.
2412	4-wire photoelectric smoke detector.
2412TH	4-wire photoelectric smoke detector w/135º F (57º C) heat
	detector.
A77–716B	EOL relay module (supervisory module for wired 4-wire fire
	zone).
2112/24T	Low-profile 4-wire photoelectric smoke detector w/135º F
	(57º C) heat detector.

– 82 –

Image 82

VistaQuest N7227V5 installation instructions Accessories Compatible Devices, No CN, Ademco 702 Outdoor, Siren

Contents

VISTA-10SE Recommendations For Smoke And Heat Detectors Recommendations For Proper Intrusion Protection Table of Contents Relay Output Devices Sequential Mode For 5800 Series Wireless Transmitters Section List of Figures HOW to USE this Manual Conventions Used in this Manual Wireless Expansion General Description Optional Phone module Supports the Ademco 4285 Phone module AC Power SupplyBack-Up Battery Communication Formats Installing the Lock if used Installing the ControlMounting the Cabinet Relay Unit if installed in cabinet Standard Phone Line Connections Standard Telephone Line Connections Wiring Table Wiring The AC TransformerInstalling The Back-Up Battery Do not Connect the Wires to the Battery YET Wiring To The Keypads Installing Remote KeypadsKeypads That May Be Used Mounting the Keypads Keypad Connections To The Control Board Preliminary Check-out Procedure Using a Supplementary Power Supply For Keypads Wiring Burglary and Panic Devices To Zones Basic HARD-WIRED ZonesInstalling the Hard-Wired Zones Wiring 4-Wire Smoke/Combustion Detectors on Zone Programming Hard-Wired Zones Zone Types Special Notes on Zone Check-Out Procedure For Hard-Wired ZonesProgramming Series Receiver Wireless Zones Wireless RF Zone Expansion 5800 RF SystemsWireless Systems Available Wireless System Operation and Transmitter Supervision Installation and Setup of the 4281/5881 Wireless Receivers Transmitter Battery LifeWireless System Installation Advisories Receiver Supervision Series Transmitter Setup Board Refer to the Compatible 5700 Series Setting the DIP SwitchesOn 5700 Series Transmitters DIP Switch Tables for 5700 RF System Wireless Devices Compatible 5700 Series Transmitters Model Product Zone/ID # Description Enter your Installer Code + # + Programming the Control For a 5700 Wireless SystemUsing the House ID Sniffer Mode 5700 Systems Zone Programming For 5700 Transmitters Programming Guide Programming 5700 RF Enter the Installer Code + # +Systems Series Transmitter Setup Compatible 5800 Series Transmitters Temp Programming the RF Transmitters 5800 RF Systems GBD Enrolling 5800 Transmitters Into The System RF House ID CodeEnrolling Through Zone Programming ZN ZT RC In L 0 0 0 0 RF Recommend that you confirm the programming of every Transmitter before proceeding to the next zone Sniffer Mode Check-Out Procedure for Wireless ZonesTransmitter ID Go/No Go Test Relay Device Basics Relay Output DevicesRelay Modules Alarm Programming Output Relays Choices for Zone Types Example of Output Relay Programming Phone Module Installing the Phone modulePhone Module Wiring General Information Terminal Connects to Caller ID Units Wiring Notes 4285 Voice Answering Module Programming The Control For Phone AccessPress 95. Ring Detection Count Downloading Field 95 Programming To Check Phone module Operation From an On-Premises Phone Checking the Operation of the 4285 Phone moduleTo Check Phone module Operation From an Off-Premises Phone External Sounders Sounder Connections Press 30. Alarm Bell TimeoutTesting the Sounder Press 51. Confirmation of Arming Ding General Information Long Range RadioConnection Wiring Connections Audio Alarm Verification AAVProgramming Connection Of AAV Unit When Not Using a 4285 Phone module Calculating the Battery Size Needed Final Power UPTo bypass this delay, press # + Example Device Current # Units Total Current Making the BatteryConnections Total = Programming the Descriptors Entering Zone Descriptors program menu modeSection Press O R Press 8 to save all words in memory Press 6 to accept the selected wordAlternate Method For Programming Zone Descriptors Method Alpha Vocabulary List For Adding Custom Words Sequential Mode For 5800 Series Wireless Transmitters Serial # ↑ Page System Communication Following describes each format in greater detail Ademco Contact ID Reporting takes the following format +1/4+1 Report Standard Expanded Communication Programming Table of Contact ID Event Codes Press 47 SPLIT/DUAL Reporting Press 45 Phone System Select Enter 1 digit default =Press 46 Report FORMAT, PRIMARY/SECONDARY To Primary Phone No To Secondary Phone No Press 61 Bypass Report Code To Program System Status and Restore Report Codes 60 68, 70Press 60 Trouble Report Code Press 62 AC Loss Report Code Press 68 Cancel Report Code Press65 OPEN/EXIT Alarm Report CODE, 1st DigitsPress 67 RF XMTR. LOW Battery Report Code Press 70 Alarm Restore Report CODE, 1st Digit Press 92 Number of Reports in Armed Period Press 74 LOW BAT Restore Report CodePress 75 RF XMTR. LOW Battery Restore Code Press 94 Download Phone Number Testing the System Test Procedure To the Installer To change the Duress code System OperationTo program a Duress code To delete the Duress code Disarmed, Not Ready Features for Each Arming ModeKeypad Functions Forced Quick Bypass Relay Outputs Keys Displayed as ZoneIf used Security Code + # + Trouble Conditions See Troubleshooting Guide also Troubleshooting Guide System including Wireless Control Before you call Technical Support, be sure you PleaseRead the Instructions VISTA-10SE Security Control Remote Keypad Specifications & AccessoriesSpecifications Remote Keypads Relay Module Phone Module Transmitter ModuleZones With the Ademco VISTA-10SE Ademco 702 Outdoor Accessories Compatible DevicesNo CN Siren Federal Communications Commission FCC Part 15 Statement Federal Communications Commission FCC Part 68 Statement UL Notices Canadian Department of Communications DOC Statement Limitations of this Alarm System ADT VISTA-10SE Summary of Connections Ademco Limited Warranty