Sequential Mode | VistaQuest N7227V5 manual

Section 13.	SEQUENTIAL MODE
	(For 5800 Series Wireless Transmitters)	............................ 61
Section 14.	SYSTEM COMMUNICATION	64
	Report Code Formats	64
	Table of Contact ID Event Codes	66
	Communication Programming	66
Section 15. TESTING THE SYSTEM		71
	Test Procedure	71
	To the Installer	72
Section 16.	SYSTEM OPERATION	73
	Security Codes	73
	Installer Code	73
	Assigning the Master Code	73
	Changing the Master Code	73
	User Codes	73
	Duress Code	73
	Keypad Functions	74
	General Information	74
	Arming Functions	74
	Panic Keys	75
	4285 Phone module (if used)	75
	Relays Outputs (if used)	75
	Exit Alarm Displays (if programmed)	75
	Trouble Conditions	76
	General Information	76
	"Check" and "Battery" Displays	76
	Power Failure	76
	Other Displays	76
Section 17.	TROUBLESHOOTING GUIDE	77
	Contacting Technical Support	79
Section 18. SPECIFICATIONS & ACCESSORIES		80
	Specifications	80
	Accessories (Compatible Devices)	82
REGULATORY AGENCY STATEMENTS		83
LIMITATIONS OF THIS ALARM SYSTEM		86
SUMMARY OF CONNECTIONS DIAGRAM		Inside Back Cover
LIMITED WARRANTY		Back Cover

NOTE: A separate Programming Guide is supplied with this manual.

– 5 –

Image 5

VistaQuest N7227V5 installation instructions Sequential Mode, For 5800 Series Wireless Transmitters Section

Contents

VISTA-10SE Recommendations For Proper Intrusion Protection Recommendations For Smoke And Heat Detectors Table of Contents Relay Output Devices For 5800 Series Wireless Transmitters Section Sequential Mode List of Figures HOW to USE this Manual Conventions Used in this Manual General Description Wireless Expansion Back-Up Battery AC Power SupplyOptional Phone module Supports the Ademco 4285 Phone module Communication Formats Mounting the Cabinet Installing the ControlInstalling the Lock if used Relay Unit if installed in cabinet Standard Telephone Line Connections Standard Phone Line Connections Installing The Back-Up Battery Wiring The AC TransformerWiring Table Do not Connect the Wires to the Battery YET Keypads That May Be Used Installing Remote KeypadsWiring To The Keypads Keypad Connections To The Control Board Mounting the Keypads Using a Supplementary Power Supply For Keypads Preliminary Check-out Procedure Installing the Hard-Wired Zones Basic HARD-WIRED ZonesWiring Burglary and Panic Devices To Zones Wiring 4-Wire Smoke/Combustion Detectors on Zone Programming Hard-Wired Zones Zone Types Programming Check-Out Procedure For Hard-Wired ZonesSpecial Notes on Zone Wireless Systems Available Wireless RF Zone Expansion 5800 RF SystemsSeries Receiver Wireless Zones Wireless System Operation and Transmitter Supervision Wireless System Installation Advisories Transmitter Battery LifeInstallation and Setup of the 4281/5881 Wireless Receivers Receiver Supervision Board Series Transmitter Setup On 5700 Series Setting the DIP SwitchesRefer to the Compatible 5700 Series Transmitters DIP Switch Tables for 5700 RF System Wireless Devices Model Product Zone/ID # Description Compatible 5700 Series Transmitters Using the House ID Sniffer Mode 5700 Systems Programming the Control For a 5700 Wireless SystemEnter your Installer Code + # + Zone Programming For 5700 Transmitters Programming Guide Systems Enter the Installer Code + # +Programming 5700 RF Series Transmitter Setup Temp Compatible 5800 Series Transmitters GBD Programming the RF Transmitters 5800 RF Systems Enrolling Through Zone Programming RF House ID CodeEnrolling 5800 Transmitters Into The System ZN ZT RC In L 0 0 0 0 RF Transmitter before proceeding to the next zone Recommend that you confirm the programming of every Transmitter ID Check-Out Procedure for Wireless ZonesSniffer Mode Go/No Go Test Relay Modules Relay Output DevicesRelay Device Basics Alarm Programming Output Relays Choices for Zone Types Example of Output Relay Programming Phone Module Wiring Installing the Phone modulePhone Module General Information Caller ID Units Terminal Connects to 4285 Wiring Notes Press 95. Ring Detection Count Programming The Control For Phone AccessVoice Answering Module Downloading Field 95 Programming To Check Phone module Operation From an Off-Premises Phone Checking the Operation of the 4285 Phone moduleTo Check Phone module Operation From an On-Premises Phone External Sounders Testing the Sounder Press 30. Alarm Bell TimeoutSounder Connections Press 51. Confirmation of Arming Ding Connection Long Range RadioGeneral Information Programming Audio Alarm Verification AAVWiring Connections Connection Of AAV Unit When Not Using a 4285 Phone module To bypass this delay, press # + Final Power UPCalculating the Battery Size Needed Example Connections Making the BatteryDevice Current # Units Total Current Total = Section Entering Zone Descriptors program menu modeProgramming the Descriptors Press O R Alternate Method For Programming Zone Descriptors Press 6 to accept the selected wordPress 8 to save all words in memory Method For Adding Custom Words Alpha Vocabulary List Sequential Mode For 5800 Series Wireless Transmitters Serial # ↑ Page Following describes each format in greater detail System Communication +1/4+1 Report Standard Expanded Ademco Contact ID Reporting takes the following format Table of Contact ID Event Codes Communication Programming Press 46 Report FORMAT, PRIMARY/SECONDARY Press 45 Phone System Select Enter 1 digit default =Press 47 SPLIT/DUAL Reporting To Primary Phone No To Secondary Phone No Press 60 Trouble Report Code To Program System Status and Restore Report Codes 60 68, 70Press 61 Bypass Report Code Press 62 AC Loss Report Code Press 67 RF XMTR. LOW Battery Report Code Press65 OPEN/EXIT Alarm Report CODE, 1st DigitsPress 68 Cancel Report Code Press 70 Alarm Restore Report CODE, 1st Digit Press 75 RF XMTR. LOW Battery Restore Code Press 74 LOW BAT Restore Report CodePress 92 Number of Reports in Armed Period Press 94 Download Phone Number Test Procedure Testing the System To the Installer To program a Duress code System OperationTo change the Duress code To delete the Duress code Keypad Functions Features for Each Arming ModeDisarmed, Not Ready Forced Quick Bypass If used Keys Displayed as ZoneRelay Outputs Security Code + # + Trouble Conditions See Troubleshooting Guide also System including Wireless Troubleshooting Guide Control Read the Instructions PleaseBefore you call Technical Support, be sure you Specifications Specifications & AccessoriesVISTA-10SE Security Control Remote Keypad Remote Keypads Zones With the Ademco VISTA-10SE Transmitter ModuleRelay Module Phone Module No CN Accessories Compatible DevicesAdemco 702 Outdoor Siren Federal Communications Commission FCC Part 68 Statement Federal Communications Commission FCC Part 15 Statement UL Notices Canadian Department of Communications DOC Statement Limitations of this Alarm System ADT VISTA-10SE Summary of Connections Ademco Limited Warranty