+1/4+1 Report Standard Expanded | VistaQuest N7227V5 manual

	3+1/4+1	3+1/4+1
Report	Standard	Expanded	4+2
Alarm	SSS(S) A	SSS(S) A	SSSS AZ
		AAA(A) Z

Trouble	SSS(S) T	SSS(S) T	SSSS Tt
		TTT(T) t

Bypass	SSS(S) B	SSS(S) B	SSSS Bb
		BBB(B) b

AC Loss	SSS(S) E	SSS(S) E	SSSS EA C
		EEE(E) A C
Low Batt	SSS(S) L	SSS(S) L	SSSS LL B
		LLL(L) L B
Open	SSS(S) O	SSS(S) O	SSSS OU
		OOO(O) U

Close	SSS(S) C	SSS(S) C	SSSS CU
		CCC(C) U

Test	SSS(S) G	SSS(S) G	SSSS Gg
		GGG(G)g

Restore	SSS(S) R	SSS(S) R	SSSS RZ
Alarm		RRR(R) Z

AC Restore	SSS(S) R A	SSS(S) R A	SSSSR A Ac
		RARARA(RA)A c
LoBat Res.	SSS(S) R L	SSS(S) R L	SSSS RLLB
		RLRLRL(RL)L B
Trouble Res.	SSS(S) R T	SSS(S) R T	SSSS RTt
		RTRTRT (R T)t
Bypass Res.	SSS(S) R B	SSS(S) R B	SSSS RBb
		RBRBRB (R B)b

Where:

Where:

SSS or SSSS = Subscriber ID		C =	Close Code–1st Digit
A =	Alarm Code–1st digit	U =	User Number (in hex)
Z =	Typically Zone Number*–2nd digit	Gg =	Test Code (1st & 2nd digits)
T t =	Trouble Code (1st & 2nd digits)	R =	Restore Code (Alarm)
Bb =	Bypass Code (1st & 2nd digits)	R T t =	Restore Code (Trbl)1st & 2nd digits
EAC =	AC Loss Code (1st & 2nd digits)	R Bb =	Restore Code (Byps)1st & 2nd digits
LLB =	Low Battery Code(1st & 2nd digits)	R AAC =	Restore Code (AC)1st & 2nd digits
O =	Open Code–1st Digit	R LLB =	Restore Code (Bat)1st & 2nd digits

*Zone numbers for: [✱] & [#], or [B] = 99 [1] + [✱], or [A] = 95	Duress = 8
[3] + [#], or [C] = 96	Tamper = 9
Ademco Contact ID Reporting takes the following format:
CCCC Q EEE GG ZZZ

where: CCCC = Customer (subscriber) ID Q = Event qualifier, where:

E = new event , and R = restore EEE = Event code (3 hexadecimal digits)

Note: For a complete list of event codes, refer to the central office receiver manual.

GG= Always 00.

ZZZ = Zone/contact ID number reporting the alarm, or user number for open/close reports. System status messages (AC Loss, Walk Test, etc.) contain zeroes in the ZZZ location.

– 65 –

Image 65

VistaQuest N7227V5 Ademco Contact ID Reporting takes the following format, +1/4+1 Report Standard Expanded

Contents

VISTA-10SE Recommendations For Proper Intrusion Protection Recommendations For Smoke And Heat Detectors Table of Contents Relay Output Devices For 5800 Series Wireless Transmitters Section Sequential Mode List of Figures HOW to USE this Manual Conventions Used in this Manual General Description Wireless Expansion Back-Up Battery AC Power SupplyOptional Phone module Supports the Ademco 4285 Phone module Communication Formats Mounting the Cabinet Installing the ControlInstalling the Lock if used Relay Unit if installed in cabinet Standard Telephone Line Connections Standard Phone Line Connections Installing The Back-Up Battery Wiring The AC TransformerWiring Table Do not Connect the Wires to the Battery YET Keypads That May Be Used Installing Remote KeypadsWiring To The Keypads Keypad Connections To The Control Board Mounting the Keypads Using a Supplementary Power Supply For Keypads Preliminary Check-out Procedure Installing the Hard-Wired Zones Basic HARD-WIRED ZonesWiring Burglary and Panic Devices To Zones Wiring 4-Wire Smoke/Combustion Detectors on Zone Programming Hard-Wired Zones Zone Types Programming Check-Out Procedure For Hard-Wired ZonesSpecial Notes on Zone Wireless Systems Available Wireless RF Zone Expansion 5800 RF SystemsSeries Receiver Wireless Zones Wireless System Operation and Transmitter Supervision Wireless System Installation Advisories Transmitter Battery LifeInstallation and Setup of the 4281/5881 Wireless Receivers Receiver Supervision Board Series Transmitter Setup On 5700 Series Setting the DIP SwitchesRefer to the Compatible 5700 Series Transmitters DIP Switch Tables for 5700 RF System Wireless Devices Model Product Zone/ID # Description Compatible 5700 Series Transmitters Using the House ID Sniffer Mode 5700 Systems Programming the Control For a 5700 Wireless SystemEnter your Installer Code + # + Zone Programming For 5700 Transmitters Programming Guide Systems Enter the Installer Code + # +Programming 5700 RF Series Transmitter Setup Temp Compatible 5800 Series Transmitters GBD Programming the RF Transmitters 5800 RF Systems Enrolling Through Zone Programming RF House ID CodeEnrolling 5800 Transmitters Into The System ZN ZT RC In L 0 0 0 0 RF Transmitter before proceeding to the next zone Recommend that you confirm the programming of every Transmitter ID Check-Out Procedure for Wireless ZonesSniffer Mode Go/No Go Test Relay Modules Relay Output DevicesRelay Device Basics Alarm Programming Output Relays Choices for Zone Types Example of Output Relay Programming Phone Module Wiring Installing the Phone modulePhone Module General Information Caller ID Units Terminal Connects to 4285 Wiring Notes Press 95. Ring Detection Count Programming The Control For Phone AccessVoice Answering Module Downloading Field 95 Programming To Check Phone module Operation From an Off-Premises Phone Checking the Operation of the 4285 Phone moduleTo Check Phone module Operation From an On-Premises Phone External Sounders Testing the Sounder Press 30. Alarm Bell TimeoutSounder Connections Press 51. Confirmation of Arming Ding Connection Long Range RadioGeneral Information Programming Audio Alarm Verification AAVWiring Connections Connection Of AAV Unit When Not Using a 4285 Phone module To bypass this delay, press # + Final Power UPCalculating the Battery Size Needed Example Connections Making the BatteryDevice Current # Units Total Current Total = Section Entering Zone Descriptors program menu modeProgramming the Descriptors Press O R Alternate Method For Programming Zone Descriptors Press 6 to accept the selected wordPress 8 to save all words in memory Method For Adding Custom Words Alpha Vocabulary List Sequential Mode For 5800 Series Wireless Transmitters Serial # ↑ Page Following describes each format in greater detail System Communication +1/4+1 Report Standard Expanded Ademco Contact ID Reporting takes the following format Table of Contact ID Event Codes Communication Programming Press 46 Report FORMAT, PRIMARY/SECONDARY Press 45 Phone System Select Enter 1 digit default =Press 47 SPLIT/DUAL Reporting To Primary Phone No To Secondary Phone No Press 60 Trouble Report Code To Program System Status and Restore Report Codes 60 68, 70Press 61 Bypass Report Code Press 62 AC Loss Report Code Press 67 RF XMTR. LOW Battery Report Code Press65 OPEN/EXIT Alarm Report CODE, 1st DigitsPress 68 Cancel Report Code Press 70 Alarm Restore Report CODE, 1st Digit Press 75 RF XMTR. LOW Battery Restore Code Press 74 LOW BAT Restore Report CodePress 92 Number of Reports in Armed Period Press 94 Download Phone Number Test Procedure Testing the System To the Installer To program a Duress code System OperationTo change the Duress code To delete the Duress code Keypad Functions Features for Each Arming ModeDisarmed, Not Ready Forced Quick Bypass If used Keys Displayed as ZoneRelay Outputs Security Code + # + Trouble Conditions See Troubleshooting Guide also System including Wireless Troubleshooting Guide Control Read the Instructions PleaseBefore you call Technical Support, be sure you Specifications Specifications & AccessoriesVISTA-10SE Security Control Remote Keypad Remote Keypads Zones With the Ademco VISTA-10SE Transmitter ModuleRelay Module Phone Module No CN Accessories Compatible DevicesAdemco 702 Outdoor Siren Federal Communications Commission FCC Part 68 Statement Federal Communications Commission FCC Part 15 Statement UL Notices Canadian Department of Communications DOC Statement Limitations of this Alarm System ADT VISTA-10SE Summary of Connections Ademco Limited Warranty