HOW to USE this Manual | VistaQuest N7227V5 specification

HOW TO USE THIS MANUAL

This manual is written to accommodate both the new and the experienced installer of Ademco products. A general description of the entire system is located in the first section of this manual. This includes the various features available and the optional peripheral devices that the system can support.

This manual is divided into separate sections. A section covering the hardwired zones (1–6) provides complete information on the capabilities of each basic hardwired zone, including its usage, programming, and a checkout procedure. Separate sections are also provided for each peripheral device that can be used in the system and includes wiring setup, programming requirements, and a checkout procedure for that device. The checkout procedures ensure that the specific device is operational in the system before proceeding to the next section. This “sectional” arrangement is also particularly useful if you are making an addition to the system at a later time (e.g., adding Wireless zones, adding a 4285 Phone module, etc.).

Without an understanding of the programming method for this system, you will not be able to successfully perform the required programming. Before any programming is attempted, we therefore urge you to read the “Mechanics of Programming” and the “Data Field Descriptions” in the separate PROGRAMMING GUIDE that has been supplied.

If you are an experienced user of Ademco products, you may choose to wire and then program the entire system at one time. If so, refer to “Mechanics of Programming” and “Data Field Descriptions” in the separate PROGRAMMING GUIDE after the hardware setup is complete. The separate PROGRAMMING GUIDE contains all of the information you will need to program the system (including a blank Programming Form), except for detailed programming for hardwired zones 1–6 and the wireless zones, which are contained in the following sections in this manual: BASIC HARDWIRED ZONES 1–6and WIRELESS (RF) ZONE EXPANSION (5700 & 5800

RF SYSTEMS).

This manual uses various icons to denote critical notes and technical tips to assist you with the installation of this system (see next page).

– 7 –

Image 7

VistaQuest N7227V5 installation instructions HOW to USE this Manual

Contents

VISTA-10SE Recommendations For Proper Intrusion Protection Recommendations For Smoke And Heat Detectors Table of Contents Relay Output Devices For 5800 Series Wireless Transmitters Section Sequential Mode List of Figures HOW to USE this Manual Conventions Used in this Manual General Description Wireless Expansion Communication Formats AC Power SupplyBack-Up Battery Optional Phone module Supports the Ademco 4285 Phone module Installing the Lock if used Installing the ControlMounting the Cabinet Relay Unit if installed in cabinet Standard Telephone Line Connections Standard Phone Line Connections Do not Connect the Wires to the Battery YET Wiring The AC TransformerInstalling The Back-Up Battery Wiring Table Wiring To The Keypads Installing Remote KeypadsKeypads That May Be Used Keypad Connections To The Control Board Mounting the Keypads Using a Supplementary Power Supply For Keypads Preliminary Check-out Procedure Wiring 4-Wire Smoke/Combustion Detectors on Zone Basic HARD-WIRED ZonesInstalling the Hard-Wired Zones Wiring Burglary and Panic Devices To Zones Programming Hard-Wired Zones Zone Types Special Notes on Zone Check-Out Procedure For Hard-Wired ZonesProgramming Wireless System Operation and Transmitter Supervision Wireless RF Zone Expansion 5800 RF SystemsWireless Systems Available Series Receiver Wireless Zones Receiver Supervision Transmitter Battery LifeWireless System Installation Advisories Installation and Setup of the 4281/5881 Wireless Receivers Board Series Transmitter Setup Transmitters Setting the DIP SwitchesOn 5700 Series Refer to the Compatible 5700 Series DIP Switch Tables for 5700 RF System Wireless Devices Model Product Zone/ID # Description Compatible 5700 Series Transmitters Zone Programming For 5700 Transmitters Programming the Control For a 5700 Wireless SystemUsing the House ID Sniffer Mode 5700 Systems Enter your Installer Code + # + Programming Guide Programming 5700 RF Enter the Installer Code + # +Systems Series Transmitter Setup Temp Compatible 5800 Series Transmitters GBD Programming the RF Transmitters 5800 RF Systems Enrolling 5800 Transmitters Into The System RF House ID CodeEnrolling Through Zone Programming ZN ZT RC In L 0 0 0 0 RF Transmitter before proceeding to the next zone Recommend that you confirm the programming of every Sniffer Mode Check-Out Procedure for Wireless ZonesTransmitter ID Go/No Go Test Relay Device Basics Relay Output DevicesRelay Modules Alarm Programming Output Relays Choices for Zone Types Example of Output Relay Programming General Information Installing the Phone modulePhone Module Wiring Phone Module Caller ID Units Terminal Connects to 4285 Wiring Notes Downloading Field 95 Programming Programming The Control For Phone AccessPress 95. Ring Detection Count Voice Answering Module To Check Phone module Operation From an On-Premises Phone Checking the Operation of the 4285 Phone moduleTo Check Phone module Operation From an Off-Premises Phone External Sounders Press 51. Confirmation of Arming Ding Press 30. Alarm Bell TimeoutTesting the Sounder Sounder Connections General Information Long Range RadioConnection Wiring Connections Audio Alarm Verification AAVProgramming Connection Of AAV Unit When Not Using a 4285 Phone module Example Final Power UPTo bypass this delay, press # + Calculating the Battery Size Needed Total = Making the BatteryConnections Device Current # Units Total Current Press Entering Zone Descriptors program menu modeSection Programming the Descriptors O R Press 8 to save all words in memory Press 6 to accept the selected wordAlternate Method For Programming Zone Descriptors Method For Adding Custom Words Alpha Vocabulary List Sequential Mode For 5800 Series Wireless Transmitters Serial # ↑ Page Following describes each format in greater detail System Communication +1/4+1 Report Standard Expanded Ademco Contact ID Reporting takes the following format Table of Contact ID Event Codes Communication Programming To Primary Phone No To Secondary Phone No Press 45 Phone System Select Enter 1 digit default =Press 46 Report FORMAT, PRIMARY/SECONDARY Press 47 SPLIT/DUAL Reporting Press 62 AC Loss Report Code To Program System Status and Restore Report Codes 60 68, 70Press 60 Trouble Report Code Press 61 Bypass Report Code Press 70 Alarm Restore Report CODE, 1st Digit Press65 OPEN/EXIT Alarm Report CODE, 1st DigitsPress 67 RF XMTR. LOW Battery Report Code Press 68 Cancel Report Code Press 94 Download Phone Number Press 74 LOW BAT Restore Report CodePress 75 RF XMTR. LOW Battery Restore Code Press 92 Number of Reports in Armed Period Test Procedure Testing the System To the Installer To delete the Duress code System OperationTo program a Duress code To change the Duress code Forced Quick Bypass Features for Each Arming ModeKeypad Functions Disarmed, Not Ready Security Code + # + Keys Displayed as ZoneIf used Relay Outputs Trouble Conditions See Troubleshooting Guide also System including Wireless Troubleshooting Guide Control Before you call Technical Support, be sure you PleaseRead the Instructions Remote Keypads Specifications & AccessoriesSpecifications VISTA-10SE Security Control Remote Keypad Relay Module Phone Module Transmitter ModuleZones With the Ademco VISTA-10SE Siren Accessories Compatible DevicesNo CN Ademco 702 Outdoor Federal Communications Commission FCC Part 68 Statement Federal Communications Commission FCC Part 15 Statement UL Notices Canadian Department of Communications DOC Statement Limitations of this Alarm System ADT VISTA-10SE Summary of Connections Ademco Limited Warranty