Zone Types | VistaQuest N7227V5 manual

	Zone Types
00	= Zone Not Used	08	= 24 Hr Aux
01	= Entry/Exit #1	09 = Fire
02	= not used	10 = Interior w/Delay
03	= Perimeter	20	= Arm Stay*
04	= Interior Follower	21	= Arm-Away*
05	= Trouble Day/Alarm Night	22	= Disarm*
06	= 24 Hr Silent	23	= No Alarm
06	= 24 Hr Silent		Response
07	= 24 Hr Audible		Response
07	= 24 Hr Audible

* 5800 RF Systems only

When the display shows the zone type you want, press [ ✱] to continue.

You must enter “00”as the zone type for any hard-wired zones that are not used.

02 Report Code

1st 03 2nd 12

3C

The report code consists of 2 hexadecimal digits, each in turn consisting of 2 numerical digits. For example, for a report code of "3C", enter [0][3] for "3" and [1][2] for "C". Refer to the SYSTEM COMMUNICATION section f o r complete information on report codes, if necessary.

Enter the desired report code and then press [ ✱] to continue.

Typical summary display


	Zn	ZT	–	RC	In L
	02	03	–	3C	HW: –



	Program Alpha?
	0 = No		1 = Yes		0

A summary display will appear, showing the data for the zone that was just programmed.

If it is programmed satisfactorily, press [✱ ] to continue.

The next request is to enter Alpha descriptors for the zones. The entry may be done now (enter 1), or may be done at a later time using ✱82 interactive mode (enter 0). See the ALPHA DESCRIPTOR PROGRAMMING section for specific procedure.

Enter Zn Num.

(00 = Quit)

03

Enter next zone number ↑

If “0” (no) was entered above, the system will return to the Enter Zone Number prompt. Proceed with the programming for the next zone, i.e., [ ✱] and zone number.

Programming Panic Keys When programming zones, note the following:

The defaults for individual panic keys or panic key pairs are: Zone 07. ✱ & #, or B: zone type 06 (24-hr silent).

Zone 95. 1 & ✱, or A: zone type 00 (not used).

Zone 96. 3 & #, or C: zone type 00 (not used).

Panic keys are programmed (or re-programmed) by keying the zone number, e.g., ✱07, ✱95, and ✱96, and entering the desired zone type that will provide the desired panic function for each of these keys, using the list of zone types below.

06 = 24 Hr Silent

07 = 24 Hr Audible

08 = 24 Hr Aux

09 = Fire

– 20 –

Image 20

VistaQuest N7227V5 installation instructions Zone Types

Contents

VISTA-10SE Recommendations For Smoke And Heat Detectors Recommendations For Proper Intrusion Protection Table of Contents Relay Output Devices Sequential Mode For 5800 Series Wireless Transmitters Section List of Figures HOW to USE this Manual Conventions Used in this Manual Wireless Expansion General Description AC Power Supply Back-Up BatteryOptional Phone module Supports the Ademco 4285 Phone module Communication Formats Mounting the Cabinet Installing the ControlInstalling the Lock if used Relay Unit if installed in cabinet Standard Phone Line Connections Standard Telephone Line Connections Wiring The AC Transformer Installing The Back-Up BatteryWiring Table Do not Connect the Wires to the Battery YET Keypads That May Be Used Installing Remote KeypadsWiring To The Keypads Mounting the Keypads Keypad Connections To The Control Board Preliminary Check-out Procedure Using a Supplementary Power Supply For Keypads Basic HARD-WIRED Zones Installing the Hard-Wired ZonesWiring Burglary and Panic Devices To Zones Wiring 4-Wire Smoke/Combustion Detectors on Zone Programming Hard-Wired Zones Zone Types Programming Check-Out Procedure For Hard-Wired ZonesSpecial Notes on Zone Wireless RF Zone Expansion 5800 RF Systems Wireless Systems AvailableSeries Receiver Wireless Zones Wireless System Operation and Transmitter Supervision Transmitter Battery Life Wireless System Installation AdvisoriesInstallation and Setup of the 4281/5881 Wireless Receivers Receiver Supervision Series Transmitter Setup Board Setting the DIP Switches On 5700 SeriesRefer to the Compatible 5700 Series Transmitters DIP Switch Tables for 5700 RF System Wireless Devices Compatible 5700 Series Transmitters Model Product Zone/ID # Description Programming the Control For a 5700 Wireless System Using the House ID Sniffer Mode 5700 SystemsEnter your Installer Code + # + Zone Programming For 5700 Transmitters Programming Guide Systems Enter the Installer Code + # +Programming 5700 RF Series Transmitter Setup Compatible 5800 Series Transmitters Temp Programming the RF Transmitters 5800 RF Systems GBD Enrolling Through Zone Programming RF House ID CodeEnrolling 5800 Transmitters Into The System ZN ZT RC In L 0 0 0 0 RF Recommend that you confirm the programming of every Transmitter before proceeding to the next zone Transmitter ID Check-Out Procedure for Wireless ZonesSniffer Mode Go/No Go Test Relay Modules Relay Output DevicesRelay Device Basics Alarm Programming Output Relays Choices for Zone Types Example of Output Relay Programming Installing the Phone module Phone Module WiringPhone Module General Information Terminal Connects to Caller ID Units Wiring Notes 4285 Programming The Control For Phone Access Press 95. Ring Detection CountVoice Answering Module Downloading Field 95 Programming To Check Phone module Operation From an Off-Premises Phone Checking the Operation of the 4285 Phone moduleTo Check Phone module Operation From an On-Premises Phone External Sounders Press 30. Alarm Bell Timeout Testing the SounderSounder Connections Press 51. Confirmation of Arming Ding Connection Long Range RadioGeneral Information Programming Audio Alarm Verification AAVWiring Connections Connection Of AAV Unit When Not Using a 4285 Phone module Final Power UP To bypass this delay, press # +Calculating the Battery Size Needed Example Making the Battery ConnectionsDevice Current # Units Total Current Total = Entering Zone Descriptors program menu mode SectionProgramming the Descriptors Press O R Alternate Method For Programming Zone Descriptors Press 6 to accept the selected wordPress 8 to save all words in memory Method Alpha Vocabulary List For Adding Custom Words Sequential Mode For 5800 Series Wireless Transmitters Serial # ↑ Page System Communication Following describes each format in greater detail Ademco Contact ID Reporting takes the following format +1/4+1 Report Standard Expanded Communication Programming Table of Contact ID Event Codes Press 45 Phone System Select Enter 1 digit default = Press 46 Report FORMAT, PRIMARY/SECONDARYPress 47 SPLIT/DUAL Reporting To Primary Phone No To Secondary Phone No To Program System Status and Restore Report Codes 60 68, 70 Press 60 Trouble Report CodePress 61 Bypass Report Code Press 62 AC Loss Report Code Press65 OPEN/EXIT Alarm Report CODE, 1st Digits Press 67 RF XMTR. LOW Battery Report CodePress 68 Cancel Report Code Press 70 Alarm Restore Report CODE, 1st Digit Press 74 LOW BAT Restore Report Code Press 75 RF XMTR. LOW Battery Restore CodePress 92 Number of Reports in Armed Period Press 94 Download Phone Number Testing the System Test Procedure To the Installer System Operation To program a Duress codeTo change the Duress code To delete the Duress code Features for Each Arming Mode Keypad FunctionsDisarmed, Not Ready Forced Quick Bypass Keys Displayed as Zone If usedRelay Outputs Security Code + # + Trouble Conditions See Troubleshooting Guide also Troubleshooting Guide System including Wireless Control Read the Instructions PleaseBefore you call Technical Support, be sure you Specifications & Accessories SpecificationsVISTA-10SE Security Control Remote Keypad Remote Keypads Zones With the Ademco VISTA-10SE Transmitter ModuleRelay Module Phone Module Accessories Compatible Devices No CNAdemco 702 Outdoor Siren Federal Communications Commission FCC Part 15 Statement Federal Communications Commission FCC Part 68 Statement UL Notices Canadian Department of Communications DOC Statement Limitations of this Alarm System ADT VISTA-10SE Summary of Connections Ademco Limited Warranty