Go/No Go Test, Enter the Installer Code + # + | VistaQuest N7227V5

Go/No Go Test

(5700/5800

RF Systems)

Before mounting transmitters permanently, conduct Go/No Go tests to verify adequate signal strength and reorient or relocate transmitters if necessary.

During this mode, wireless receiver gain is reduced by 50%. Testing in this mode assists in determining good mounting locations for the transmitters and verifies that the RF transmission has sufficient signal amplitude margin for the installed system.

1.Enter the Installer Code + # + 4

2.Once transmitters are placed in their desired locations and the approximate length of wire to be run to sensors is connected to the transmitter's screw terminals, fault each transmitter. Do not conduct this test with your hand wrapped around the transmitter as this will cause inaccurate results.

•The keypad will beep three times to indicate signal reception.

•If the keypad does not beep, re-orient or move the transmitter to another location. Usually a few inches in either direction is all that is required.

3.Mount the transmitter according to the instructions provided with the transmitter.

4.Exit the GO/NO GO test mode by entering Installer Code + (OFF).

– 38 –

Image 38

VistaQuest N7227V5 installation instructions Go/No Go Test, Enter the Installer Code + # +

Contents

VISTA-10SE Recommendations For Smoke And Heat Detectors Recommendations For Proper Intrusion Protection Table of Contents Relay Output Devices Sequential Mode For 5800 Series Wireless Transmitters Section List of Figures HOW to USE this Manual Conventions Used in this Manual Wireless Expansion General Description Optional Phone module Supports the Ademco 4285 Phone module AC Power SupplyBack-Up Battery Communication Formats Mounting the Cabinet Installing the ControlInstalling the Lock if used Relay Unit if installed in cabinet Standard Phone Line Connections Standard Telephone Line Connections Wiring Table Wiring The AC TransformerInstalling The Back-Up Battery Do not Connect the Wires to the Battery YET Keypads That May Be Used Installing Remote KeypadsWiring To The Keypads Mounting the Keypads Keypad Connections To The Control Board Preliminary Check-out Procedure Using a Supplementary Power Supply For Keypads Wiring Burglary and Panic Devices To Zones Basic HARD-WIRED ZonesInstalling the Hard-Wired Zones Wiring 4-Wire Smoke/Combustion Detectors on Zone Programming Hard-Wired Zones Zone Types Programming Check-Out Procedure For Hard-Wired ZonesSpecial Notes on Zone Series Receiver Wireless Zones Wireless RF Zone Expansion 5800 RF SystemsWireless Systems Available Wireless System Operation and Transmitter Supervision Installation and Setup of the 4281/5881 Wireless Receivers Transmitter Battery LifeWireless System Installation Advisories Receiver Supervision Series Transmitter Setup Board Refer to the Compatible 5700 Series Setting the DIP SwitchesOn 5700 Series Transmitters DIP Switch Tables for 5700 RF System Wireless Devices Compatible 5700 Series Transmitters Model Product Zone/ID # Description Enter your Installer Code + # + Programming the Control For a 5700 Wireless SystemUsing the House ID Sniffer Mode 5700 Systems Zone Programming For 5700 Transmitters Programming Guide Systems Enter the Installer Code + # +Programming 5700 RF Series Transmitter Setup Compatible 5800 Series Transmitters Temp Programming the RF Transmitters 5800 RF Systems GBD Enrolling Through Zone Programming RF House ID CodeEnrolling 5800 Transmitters Into The System ZN ZT RC In L 0 0 0 0 RF Recommend that you confirm the programming of every Transmitter before proceeding to the next zone Transmitter ID Check-Out Procedure for Wireless ZonesSniffer Mode Go/No Go Test Relay Modules Relay Output DevicesRelay Device Basics Alarm Programming Output Relays Choices for Zone Types Example of Output Relay Programming Phone Module Installing the Phone modulePhone Module Wiring General Information Terminal Connects to Caller ID Units Wiring Notes 4285 Voice Answering Module Programming The Control For Phone AccessPress 95. Ring Detection Count Downloading Field 95 Programming To Check Phone module Operation From an Off-Premises Phone Checking the Operation of the 4285 Phone moduleTo Check Phone module Operation From an On-Premises Phone External Sounders Sounder Connections Press 30. Alarm Bell TimeoutTesting the Sounder Press 51. Confirmation of Arming Ding Connection Long Range RadioGeneral Information Programming Audio Alarm Verification AAVWiring Connections Connection Of AAV Unit When Not Using a 4285 Phone module Calculating the Battery Size Needed Final Power UPTo bypass this delay, press # + Example Device Current # Units Total Current Making the BatteryConnections Total = Programming the Descriptors Entering Zone Descriptors program menu modeSection Press O R Alternate Method For Programming Zone Descriptors Press 6 to accept the selected wordPress 8 to save all words in memory Method Alpha Vocabulary List For Adding Custom Words Sequential Mode For 5800 Series Wireless Transmitters Serial # ↑ Page System Communication Following describes each format in greater detail Ademco Contact ID Reporting takes the following format +1/4+1 Report Standard Expanded Communication Programming Table of Contact ID Event Codes Press 47 SPLIT/DUAL Reporting Press 45 Phone System Select Enter 1 digit default =Press 46 Report FORMAT, PRIMARY/SECONDARY To Primary Phone No To Secondary Phone No Press 61 Bypass Report Code To Program System Status and Restore Report Codes 60 68, 70Press 60 Trouble Report Code Press 62 AC Loss Report Code Press 68 Cancel Report Code Press65 OPEN/EXIT Alarm Report CODE, 1st DigitsPress 67 RF XMTR. LOW Battery Report Code Press 70 Alarm Restore Report CODE, 1st Digit Press 92 Number of Reports in Armed Period Press 74 LOW BAT Restore Report CodePress 75 RF XMTR. LOW Battery Restore Code Press 94 Download Phone Number Testing the System Test Procedure To the Installer To change the Duress code System OperationTo program a Duress code To delete the Duress code Disarmed, Not Ready Features for Each Arming ModeKeypad Functions Forced Quick Bypass Relay Outputs Keys Displayed as ZoneIf used Security Code + # + Trouble Conditions See Troubleshooting Guide also Troubleshooting Guide System including Wireless Control Read the Instructions PleaseBefore you call Technical Support, be sure you VISTA-10SE Security Control Remote Keypad Specifications & AccessoriesSpecifications Remote Keypads Zones With the Ademco VISTA-10SE Transmitter ModuleRelay Module Phone Module Ademco 702 Outdoor Accessories Compatible DevicesNo CN Siren Federal Communications Commission FCC Part 15 Statement Federal Communications Commission FCC Part 68 Statement UL Notices Canadian Department of Communications DOC Statement Limitations of this Alarm System ADT VISTA-10SE Summary of Connections Ademco Limited Warranty