Baldor GLC30, GLC60, GLC105, GLC45, GLC20, GLC65, GLC100, GLC15, GLC25, GLC40 manual Parameter Setting

Figure 4‐18 Analog Fault Menu Loop Parameters

Fault Name	Input Analog	Fault	Setpoint Level	Setpoint Level	Action	Alarm Latch	Bypass On	Transient
	Type	E=Enable	(Pick-up)	(Drop-out)	S=Shutdown	Y=Yes	Start	Delay (Sec)
		D=Disable			A=Alarm	N=No	Y=Yes
							N=No
Under Voltage	AC Voltage	E*			S	Y	Y*	5.0
Under Frequency	AC Frequency	E*			S	Y	Y*	5.0
Weak Battery	DC Voltage	E*	18.0	N/A	A*	Y	N*	3.0
Low Battery	DC Voltage	E*	25.6	N/A	A*	N	N*	120.0
Voltage
High Battery	DC Voltage	E*	30.4	N/A	A*	N	N*	10.0
Voltage
Low Engine Temp	Temp Sender	E*	95 °F	N/A	A*	Y	N*	5.0
High ENG Temp #1	Temp Sender	E*	198 °F	N/A	A	Y	Y	2.0
Alarm
High ENG Temp #2	Temp Sender	E*	206 °F	N/A	S	Y	Y	2.0
Shutdown
Low Oil Press #1	Press Sender	E*	30PSI	N/A	A	Y	Y*	2.0
Alarm
Low Oil Press #2	Press Sender	E*	20PSI	N/A	S	Y	Y*	2.0
Shutdown

* Indicates parameter is non-programmable.

Figure 4‐19 Digital Fault Menu Loop Parameters

Fault Name	Input #	Action	Alarm Latch	Polarity	Bypass On	Transient
		S=Shutdown	Y=Yes	O=Open	Start	Delay (Sec)
		A=Alarm	N=No	C=Close	Y=Yes
					N=No
Low Oil Pressure	1	S	-	O	Y	0.5
High ENG TEMP	2	S	-	O	Y	1.0
Batt Chgr Input Fail	3	A	Y	C	N	30.0
Low Fuel Level	4	A	N	C	N	0.1

		Figure 4‐20 Calibration Menu Loop Parameters
Parameter	Setting
Volts A-B	Zero XXX	XXXVAC
Volts A-B	Span XXX	XXXVAC
Volts B-C	Zero XXX	XXXVAC
Volts B-C	Span XXX	XXXVAC
Volts C-A	Zero XXX	XXXVAC
Volts C-A	Span XXX	XXXVAC
Volts A-N	Zero XXX	XXXVAC
Volts A-N	Zero XXX	XXXVAC
Volts B-N	Zero XXX	XXXVAC
Volts B-N	Zero XXX	XXXVAC
Volts C-N	Zero XXX	XXXVAC
Volts C-N	Zero XXX	XXXVAC
Current A	Zero XXX	XXXAAC
Current A	Span XXX	XXXAAC
Current B	Zero XXX	XXXAAC
Current B	Span XXX	XXXAAC
Current C	Zero XXX	XXXAAC
Current C	Span XXX	XXXAAC
Battery Voltage	Span XXX	XX.X VDC
Engine Temperature	XXX	XXX C/F
Oil Pressure	XXX	XXXX PSI/KPA

4‐32 Operation MN2408