Manuals / Baldor / Lawn and Garden / Portable Generator

Baldor MN1274 06/2001 DC Bus power connections from package size C, To external, drives, with

Models: MN1274 06/2001

1 154

Download 154 pages 13.87 Kb

Page 29

2.3.9DC Bus power connections from package size C

2.3.9DC Bus power connections from package size C

			Location	Connector X1, single or 2-part connector

			Part number	MD1AxxSx...	MD2AxxSx...

To external			Output voltage	160VDC	320VDC
To external
drive(s)			Range	135-176VDC	306-350VDC
with
with
Vcc inputs

The MintDrive 10A and 15A variants are available with a DC bus supply output for powering other drives that do not have their own internal mains power supplies. This power is available on the X1 connector pins Vcc+ and Vcc-.

MintDrive

(MD1AxxSx... )

Vcc+

Vcc-

R1

R2

External drive

Vcc+

Vcc-

Vcc+

Vcc-

External drive

Vcc+

Vcc-

Vcc+

Vcc-

Regeneration

Resistor

Note: It is important to ensure that the total current required by the powering drive, the external drive(s) and their maximum combined loads does not exceed the current rating of the powering drive.

Tightening torque for terminal block connections is 4.4~5.3 lbin (0.5~0.6Nm).

The threaded holes in the top and bottom of the enclosure are for cable clamps (provided). The holes are threaded for M4 bolts no longer than 0.47” (12mm) in length. Longer bolts may short circuit the electrical components inside the MintDrive.

17

Image 29

Baldor MN1274 06/2001 DC Bus power connections from package size C, To external, drives, with, Vcc inputs

Contents

Installation Manual MN1274 06/2001Page Baldor Italia S.R.L Precautions Safety Noticedevices installed CAUTION Removing the cover will invalidate UL certification Introduction ContentsBasic Installation 4.2 Mint Configuration Tool Startup Wizard - coarse tuning Tuning and ConfigurationInput / Output viiiMint WorkBench TroubleshootingSpecifications Appendices A TuningCE Guidelines Accessories and optionsPage 1 Introduction 1.1 MintDrive features1.2 Receiving and inspection Installed at1.2.1 Identifying the catalog number Catalog number MD1.3.1 Monitor LED display 1.3 MintDrive indicators1.3.2 CAN 1 and 2 LEDs 1.3.3 Ready LED1.4 Units and abbreviations 2.1.1 Hardware requirements 2 Basic Installation2.1 Outline Meaning 2.1.5 Other information needed for installation 2.1.3 Power sources2.1.2 RS485 / RS422 systems 2.1.4 Tools and miscellaneous hardware2.2 Mechanical installation and location requirements Figure 1 - Package dimensions 2.2.1 Dimensions and mounting2.3 Power connections MintDrive 2.3.1 GroundingSingle phase units Figure 2 - Recommended single phase system groundingMintDrive 2.3.2 Input power conditioning2.3.3 Power disconnect and protection devices Figure 6 - Circuit breaker and fuse, three phase, package size C Figure 5 - Circuit breaker and fuse, single phase, package size CMintDrive MintDrive2.3.4 Wire sizes E L N 2.3.5 Single phase connection to package size A or B2.3.6 Single phase connection to package size C MDxxxxxx-xxx 2.3.7 Three phase connection to package size C2.3.8 24V control supply To external 2.3.9 DC Bus power connections from package size Cdrives with2.3.10 Power supply filters 2.4 Motor connections 2.4.1 Motor circuit contactors 2.4.2.1 Regeneration resistor mounting 2.4.2 Regeneration resistor Dynamic Brake resistor2.5 Feedback connections Resolver function 2.5.1 Resolver optionBaldor MotorGrey 2.5.1.1 Resolver cable pin configurationEncoder Hall Feedback 2.5.2 Encoder option1 CHA+ 6 CHA 2 CHB+ 7 CHB 3 CHZ+ INDEX 8 CHZ- INDEX 11 +5V 13 DGND 4 Hall U+ 5 Hall U 9 Hall W+ 14 Hall W 10 Hall V+ 15 HallThis completes the basic installation 2.6 Drive enableYou should read the following sections in sequence before attempting to start the MintDrive3.2 Analog I/O 3 Input / Output3.1 Outline AIN2 ADC.2 3.2.1 Analog Input, Single EndedAIN3 ADC.3 3.2.2 Analog Input, DifferentialAIN1 ADC.1 3.2.3 Analog Inputs, DifferentialAIN0 Page AUXDAC.3 3.2.4 Analog Outputs, BipolarAUXDAC.2 AUXDAC.1 3.2.5 Analog Outputs, BipolarAUXDAC.0 3.3 Digital I/O not connected not connected 3.3.1 Digital InputsFigure 16 - Motor thermal switch circuit 3.3.1.1 Thermal switch connection3.3.2 Digital Inputs 3.3.2.2 Breakout board 3.3.2.1 Special functions on inputs DIN0 and DIN2Source 3.3.3 Digital OutputsSink USR GND 3.3.4 Digital OutputsRelay coil with flyback diode 3.4.1 Simulated encoder output 3.4 Other I/OEncoder 3.4.2 Master auxiliary encoder inputCHA+ CHA-- CHB+ CHB-- CHZ+ CHZ-- +5V DGND Connection of shieldsFigure 22 - Auxiliary encoder circuit Location 3.4.3 Serial portRS232 Name RS485 / RS422 nameFigure 23 - RS232 serial port connections 3.4.4 Using RS232 cable3.4.5 Multidrop using RS485 / RS422 cable 3.4.6 Connecting Baldor HMI Operator Panels 3.4.7 Optional breakout board for connector This completes the input/output wiring3.4.8 CAN peripherals You should read the following sections in sequence before4.1.1 Connecting the MintDrive to the PC 4 Tuning and Configuration4.1.2 Installing the software 4.1 Outline4.1.3 Starting the MintDrive 4.2 Mint Configuration Tool Startup Wizard - coarse tuning 3. Click Next Important Note 4.3.1 An introduction to closed loop control 4.3 MCT Startup Wizard - fine-tuningIn summary, the following rules can be used as a guide 4.3.2 Fine-tuning the speed loop 4.3.3 Fine-tuning the position loop Demand position Measured position Demand position Measured position 5. Click Start MoveDemand position Measured position 4.3.4 Jog test 1. Click Mint Configuration Tool in Wizard Mode 4.3.5 Completing the Startup Wizard4.4.1 Digital input configuration 4.4 MCT Wizard - hardware configuration4.4.2 Digital output configuration 4.4.4 Axis0 error configuration 4.4.3 Axis0 parameter configurationWhen you have finished, click Next to continue When you have finished, click Next to continue4.4.6 Miscellaneous configuration 4.4.5 Axis0 tuning configuration4.4.7 Completing the configuration wizard Select a folder and enter a filename for the configuration file 5. The second file to save is the configuration fileH The configuration file will be saved H MCT will be closed H The configuration file will be automatically loaded into WorkBench5.1.1 Completing configuration This completes the configuration and tuningmovement commands that can be useful for testing 5 Mint WorkBench5.2.1 Selecting the controller 5.2 Using WorkBench5.2.2 Menus and buttons 5.2.2.1 Standard toolbar functions5.2.2.3 Macro toolbar functions 5.2.2.2 Motion toolbar functions5.2.2.4 Status bar 5.2.2.5 CAN window5.3.1 Quick Watch tab 5.3 Watch window740 × L × A∕V 5.3.2 Speed Loop tab5.3.3 Position Loop tab 5.3.4 Capture tab 5.4.2 Program window 5.4.1 Configuration window5.4 Editor windows 5.4.3 Terminal window 5.4.4 Useful commands for testingTo start the motor turning slowly, type To stop the motor turning, typeTo change the speed, type Combining commands on one lineTo turn a distance of 5 turns, type 5.4.5 Firmware update Page 6.1 Outline 6 Specifications6.1.1 General specifications VRIPPLE = 10% 6.1.2 Power6.1.4 Resolver feedback 6.1.3 Rectifier and regeneration6.1.5 Encoder feedback 6.1.6 Control signalsMinimum 6.1.7 EnvironmentalMaximum DeratePage 7.1 Outline 7 Troubleshooting7.1.1 Problem diagnosis Communication 7.1.2Problem Checkcorrupted. Use RELEASE 7.1.3 Power upCorruption. Use NEW to clear buffers. is shown atCheck Problemproportional gain manually and proceed to the feedback alignment 7.1.4 Tuning7.1.5 Mint gains CONFIG = cfSERVOCONFIG = cfCURRENTAMPLIFIER 7.1.6 Ready LED is red PRINT DRIVEFAULTCode ProblemCheck If this occurs during acceleration then the load may be too great forCheck ProblemCode Check 7.1.7 CANProblem Check ProblemPage A Tuning A A.1 Introduction Motor Speed Filter 16 Sample Filter Figure A.1 MintDrive Closed Loop SystemA.1.1 Closed loop control A.1.2 Position loop  + KFCommand = KIP.e + KII.Σe Command = KVP.e + KVI.ΣeA.1.3 Speed loop A.1.4 Current loopA.1.7.1 Position Loop gain terms A.1.6 Tuning the position loop for a velocity servo driveA.1.7 Tuning the position loop for a servo drive FOLERROR KINTMODE=2Speed increase = KPROP x FOLERROR / KVELFF A.1.7.3 Position Loop Tuning using a trapezoidal move type A.1.7.2 Position Loop Tuning using a step moveCONFIG=6 A.1.8 Tuning the position loop for a torque servo driveA.1.9 Saving tuning information Page B.1.1 MintDrive capabilities B CAN B B.1 OutlineH Terminators must only be fitted at both ends of the network, not at intermediate nodes B.2.1 CAN 1 CANopen B.2 CAN 1 CANopenType B.2.2 What is CANopen?Mint Constant Node TypeB.2.4 Network manager - node B.2.3 Configuring nodesB.2.5 Scanning nodes NODE = CANBAUD.1 =B.2.6 Connecting to nodes B.2.7 Monitoring CAN events B.2.8.2 Broadcast communication B.2.8 Controller nodesB.2.8.1 Singlecast communication B.2.8.3 Comms array subroutines B.2.9.1 Digital I/O accessB.2.9 I/O nodes B.2.9.3 Extra Analog I/O Functionality B.2.9.2 Analog I/O Access? REMOTEINX.1.2.0 ? REMOTEOUTX.1.2.0Data format B.2.10 HMI Operator PanelsHMI database variable HMI variable indexThe HMI communicates its own changes to the MintDrive using CAN event B.3.1 CAN 2 Baldor CAN B.3 CAN 2 Baldor CANB.3.3 Preparing the CAN peripheral B.3.4 Connecting the PC, MintDrive and CAN peripheralB.3.2 Preparing the MintDrive REMOTESETUP B.3.6 Static configurationB.3.5 Node IDs Node Type = inputnode8 Current Node Number = Serial Number =B.3.7 Adding the node to the network B.3.10 Normal operation B.3.8 Monitoring CAN Bus communicationsB.3.9 Controlling the CAN peripheral B.3.11 KeypadNode Figure B.1 ioNode 24/24 B.3.12 ioNode 24/24B.3.13 Example CAN network B.3.14 Mint CAN related keywords B.3.14.1 Using abbreviationsPage C.1.1 Declaration of Conformity C CE GuidelinesC.1 Outline C.1.2 EMC Conformity and CE marking C.1.4 EMC wiring techniqueC.1.3 Use of CE compliant components CabinetGrounding Earth C.1.5 EMC installation suggestionsEMC filters Conductive C.1.6 Wiring of shielded screened cablesClamp Resolver ConnectorEncoder Connector Handwheel / Encoder HousingHousing Connector backshellPage D.1.1 Cables D Accessories and optionsD.1 Outline Cable assembly D.1.2 Resolver feedback cableMotor type Baldor catalogD.1.3.1 Catalog numbers D.1.3.2 Filter dimensions - FN351-36-33 and FN351-50-33D.1.3 EMC mains filters Page D.1.4 Regeneration resistors Figure D.1 MintDrive X5 breakout board D.1.5 Breakout boardPage MN1274 06/2001 Mint Motion Centre 6 Bristol Distribution Park Hawkley Drive, BristolBS32 0BF, UK