CHAPTER VI TROUBLESHOOTING

4.TROUBLESHOOTING OF MALFUNCTIONS

M-1 No DC power supplied

Possible cause

Step

Check

Result

Remedy

 

 

 

 

 

PCBs

1

Does any PCB have the short circuit between

Yes

Replace the PCB having the

 

 

+24V and 0V,+5V and 0V or +24V and +5V?

 

short circuit.

 

 

 

 

 

Low-voltage

2

Is the voltage of P3-8 in the low-voltage power

Yes

Replace the low-voltage power

power supply

 

supply PCB connector 0V?

 

supply PCB assy.

PCB

 

 

 

 

 

 

No

Replace the main PCB assy,

Main PCB

 

 

LV harness

 

 

 

the LV harness or the DC fan

DC fan motor

 

 

 

motor.

 

 

 

 

 

M-2

Malfunction of LCD display on the control panel.

Possible cause

Step

 

 

Check

 

Result

Remedy

 

 

 

 

 

LCD module

1

Dose the voltage of the following signals

Yes

Replace the control panel

 

 

vary to 5V or 0V when the LCD displays are

 

unit.

Control panel

 

changed through switch operations?

 

 

 

 

 

No

Replace the main PCB assy,

PCB

 

(Check following signals using the digital

 

 

the switch flat cable or the

 

 

memory scope with the trigger function for

 

Switch flat cable

 

 

control panel unit.

 

this check)

 

 

 

Main PCB

 

Signal

Main PCB Panel PCB

LCD

 

 

 

 

PAD4

P1-9

--- P1-13 --- P2-4

--- 7

 

 

 

 

PAD5

P1-5

--- P1-17 --- P2-3

--- 8

 

 

 

 

PAD6

P1-11

--- P1-11 --- P2-2

--- 9

 

 

 

 

PAD7

P1-4

--- P1-18 --- P2-1

--- 10

 

 

 

 

LCDRS

P1-3

--- P1-19 --- P2-7

--- 4

 

 

 

 

LCDE

P1-2

--- P1-20 --- P2-5

--- 6

 

 

 

 

 

 

 

 

 

 

M-3

Malfunction of control panel LED lamps.

Possible cause

Step

 

Check

 

Result

Remedy

 

 

 

 

 

LED lamps

1

Dose the voltage of the following signals stay

Yes

Replace the control panel

Control panel

 

0V while the "04 SELF TEST " is displayed

 

unit.

 

after switching the power on and stay 5V for

 

 

 

No

Replace the main PCB assy

PCB

 

about 0.5 seconds after the message goes off?

 

 

(Do the LED lamps turn on and off in response

 

or the switch flat cable.

Switch flat cable

 

 

 

 

to the signal levels of 0V and 5V?)

 

 

Main PCB

 

Signal

Main PCB Panel PCB

 

 

 

 

LED1(ON LINE)

P1-13

--- P1-9

 

 

 

 

LED2(READY)

P1-7

--- P1-15

 

 

 

 

LED3(DATA)

P1-1

--- P1-21

 

 

 

 

LED4(ALARM)

P1-6

--- P1-16

 

 

 

 

 

 

 

 

 

VI - 1

Page 153
Image 153
Brother HL-1260 service manual No DC power supplied, Malfunction of LCD display on the control panel