Cisco Systems 10200 manual Tone Frequencies and Cadences, SC1D-ACT Stutter Tone, SC2D-ACT

Appendix A Feature Tones

Tone Frequencies and Cadences

Table A-1	Feature Tones (continued)
Feature		Tone	Condition(s) That Initiate Tone1
SC1D-ACT		STUTTER TONE	Stutter tone is used once after the subscriber enters the *74 (SC1D
SC2D-ACT			activation) or *75 (SC2D activation) to begin the process of collecting
			the information required to provision one of the speed call slots. After a
			speed call slot has been successfully provisioned, the subscriber will
			again receive the stutter tone to signify that the speed call slot was
			successfully provisioned.
VMWI 3		STUTTER TONE	The subscriber has VMWI and has a message waiting, but the serving
			MGW does not have a visual indicator.

1.When more than one condition is listed for a single tone, any one of the conditions can cause the tone to be played.

2.For more information on the screening list, refer to the Cisco BTS 10200 Softswitch System Description.

3.MWI = message waiting indicator; VMWI = visual message waiting indicator.

Tone Frequencies and Cadences

Tones are requested by the BTS and delivered to the subscriber or operator by the MGW. Some MGWs can be provisioned to play tone cadences different than the ones described in this table.

Table A-2		Subscriber and Operator Tone Descriptions
	Tone		Frequency (Hz)	Cadence Played by MGW
	Alerting pattern (ringing) 1		440 + 480	2 sec on, 4 sec off, repeating
	Alerting pattern (ringing) 2		440 + 480	0.8 sec on, 0.4 sec off, 0.8 sec on, 4.0 sec off, repeating
	Alerting pattern (ringing) 3		440 + 480	0.4 sec on, 0.2 sec off, 0.4 sec on, 0.2 sec off, 0.8 sec on, 4 seconds
				off, repeating
	Alerting pattern (ringing) 4		440 + 480	0.3 sec on, 0.2 sec off, 1 sec on, 0.2 sec off, 0.3 sec on, 4 sec
				off, repeating
	Alerting pattern (ringing) 5		440 + 480	0.5 sec on once
	Alerting pattern (ringing) 6		440 + 480	1 sec on, 3sec off, repeating
	Busy verification		440	2 sec burst, followed by 0.5 sec burst every 10 sec
	(used for operator BLV 1)
	CW tone		440	0.3 sec on once
	CW Type 1		440	0.3 sec on once
	CW Type 2		440	0.1 sec on, 0.1 sec off, 2 times
	CW Type 3		440	0.1 sec on, 0.1 sec off, 3 times
	CW Type 4		440	0.1 sec on, 0.1 sec off, 0.3 sec on, 0.1 sec off, 0.1 sec on
	Confirmation tone		350 + 440	0.1 sec on, 0.1 sec off, 3 times
	Dial tone		350 + 440	steady on
	Line busy tone		480 + 620	0.5 sec on, 0.5 sec off, repeating
	Message waiting indicator tone		350 + 440	10 bursts (0.1 sec on, 0.1 sec off), then steady on
	Off-hook warning tone		1400 + 2060 +	0.1 sec on, 0.1 sec off, repeating
	(receiver off-hook tone)		2450 + 2600
		Cisco BTS 10200 Softswitch Operations and Maintenance Guide, Release 6.0.x
	A-6			OL-16000-07