Manuals / Brands / Power Tools / Welding System / Cisco Systems / Power Tools / Welding System

Cisco Systems 2130, 2140 Removing and Installing the Processor Air Duct

1 116

Download 116 pages, 4.56 Mb

4-7

Cisco Application Deployment Engine (ADE) 2130 and 2140 Series Appliance Hardware Installation Guide

78-18579-02

Chapter4 Installing the Cisco ADE 2130 and 2140 Series Appliance Hardware Options

Removing and Installing the Processor Air Duct

Figure4-3 Installing the Hard Drive Tray

Step10 Press the lever until it snaps shut to secure the drive into the drive bay.

Removing and Installing the Processor Air Duct

This section contains the following topics:

•Removing the Processor Air Duct, page4-7

•Installing the Processor Air Duct, page 4-9

Removing the Processor Air Duct

The air duct must be removed to access the processors and the DIMMs.

Caution The processor air duct is required for proper airflow within the chassis. Be sure the air duct is in place

again before installing the appliance cover.

1Drive tray

231202

A

Contents

Main Page CONTENTS Page Page Page About This Guide Document Revision History Objectives Audience Organization Conventions x Safety Warnings xi xii xiii Page Related Documentation Obtaining Documentation and Submitting a Service Request Page Introducing the Cisco Application Deployment Engine 2130 and 2140 Series Appliance Product Overview Product Serial Number Location Cisco Product Identification Tool Cisco ADE 2130 and 2140 Series Appliance Configurations Cisco ADE 2130 Series Appliance Cisco ADE 2140 Series Appliance Hardware Features Cisco ADE 2130 and 2140 Series Appliance Front View Front Control Panel LEDs and Switches Cisco ADE 2130 and 2140 Series Appliance Rear View NIC LEDs AC and DC Power Supply LEDs Input/Output Ports and Connectors Ethernet Port (NIC 1 and NIC 2) Ethernet Port Connector Serial (Console) Port Serial (Console) Port Connector Serial (Console) Port Cables AC and DC Power Supplies AC Power Supply Input DC Power Supply Input Environmental Monitoring Overcurrent Protection (OCP) Overvoltage Protection (OVP) Overtemperature Protection (OTP) Regulatory Compliance Preparing to Install the Cisco ADE 2130 and 2140 Series Appliance Safety Guidelines General Precautions Safety with Equipment Safety with Electricity 2-4 Follow these guidelines when working on equipment powered by electricity: quickly turn off the power. Working on or near power supplies Installing or removing an appliance Preventing Electrostatic Discharge Damage Lifting Guidelines Preparing Your Site for Installation Site Planning Rack Installation Safety Guidelines Enclosed Rack (Do Not Use) 4-Post (Open) Rack 2-Post (Telco) Rack Site Environment Airflow Guidelines Temperature and Humidity Guidelines Power Considerations AC Power Supply Safety Considerations DC Power Supply Safety Considerations Method of Procedure Unpacking and Checking the Contents of Your Shipment Cisco Information Packet and Warranty Required Tools and Equipment Installation Checklist Creating a Site Log Ethernet and Console Port Considerations NIC 1 and NIC 2 (RJ-45) Ethernet Connections Serial (Console) Port Connections Page Page Installing the Cisco ADE 2130 and 2140 Series Appliance Rack-Mounting Configuration Guidelines Mounting the Cisco ADE 2130 and 2140 Series Appliance in a 2-Post Rack 2-Post Rack-Mount Hardware Kit 1 2 3 Mid-Mounting in a 2-Post Rack Attaching the L Brackets to the Appliance Installing the Appliance in the Rack Mounting the Cisco ADE 2130 and 2140 Series Appliance in a 4-Post Rack 4-Post Rack-Mount Hardware Kit Attaching the Inner Slide Rails to the Appliance 1 2 4 3 Attaching the Outer Slide Rails to the Rack Installing the Appliance into the Rack Page Cisco ADE 2130 and 2140 Series Appliance Power Connecting the Appliance AC Power Power Connections Grounding the Rack Connecting the Appliance DC Power and Ground Grounding Connections Power Connections 3-16 Wiring the DC-Input Power Source To connect the DC power supply to the Cisco ADE 2130 and 2140 Series appliance: Grounding Connections section on page3-14. Page Connecting the Network and Console Cables Connecting the Network Interface Connecting the Console Cable Management Powering Up the Cisco ADE 2130 and 2140 Series Appliance Power-Up Procedure (AC Power Supply) Power-Up Procedure (DC Power Supply) Checking the LEDs Removing or Replacing the Cisco ADE 2130 and 2140 Series Appliance Installing the Cisco ADE 2130 and 2140 Series Appliance Hardware Options Before You Begin Preparing for a Successful Installation Hardware Options Tools and Supplies Needed Beginning the Installation Removing the Cover Page Removing the Front Bezel Installing a Hard Drive Tray into the Appliance Page Removing and Installing the Processor Air Duct A Removing the Processor Air Duct A B C E D Installing the Processor Air Duct Installing and Removing Memory DIMM D2 Channel A Branch 1 DIMM A2 Branch 0 Installing DIMMs E A C DB Removing DIMMs Removing and Installing the PCI Adapter Card Page Removing the PCI Riser Assembly Removing a PCI Adapter Card C B D E Installing a PCI Adapter Card Installing the PCI Riser Assembly Installing or Replacing a Power Supply Replacing a Redundant Power Supply Replacing a Nonredundant Power Supply Adding a New Redundant Power Supply Completing the Installation Installing the Cover Page Page A Troubleshooting Troubleshooting Overview Problem Solving Troubleshooting the Power and Cooling Systems Environmental Reporting Features Troubleshooting Adapter Cards, Cables, and Connections Reading the LEDs Front-Panel LEDs NIC LEDs Product Serial Number Location Cisco Product Identification Tool Page B Site Log Page C Maintaining the Cisco ADE 2130 and 2140 Appliance Maintaining Your Site Environment General Exterior Cleaning and Inspection Appliance Dust and Particles Cables and Connectors Adapter Cards Cooling Temperature Humidity Altitude Electrostatic Discharge Electromagnetic and Radio Frequency Interference Magnetism Power Source Interruptions Page INDEX Numerics A B C D E F G H I K L M N R S T U W