Cisco Systems RSP8 CPU

Route Switch Processor (RSP8) Installation and Configuration Guide

OL-4920-02

Product Description

Figure2 RSP8 Components

CPU

The CPU used in the RSP8 is a 250-MHz R7000 with 256-KB Layer 2 cache.

1MEMD SRAM 6Flash EPROM (ROMmon) U7

2Bus connectors 7Auxiliary port

3CPU 8Flash memory SIMM holder

4DRAM DIMMs (bank 0: bottom)

DRAM DIMMs (bank 1: top) U12

U15 9PC Card slot 0: bottom

PC Card slot 1: top

(for Flash Disks or Memory Cards)

5Console port

ROUTE SWITCH PROCESSOR 16

SLOT 1

SLOT 0

NORMAL

AUX

CONSOLE

H7188

U7 U12 U15

Contents

Main Route Switch Processor (RSP8) Installation and Configuration Guide Document Contents Related Documentation Product Description Page CPU Memory Components DRAM SRAM NVRAM Flash Memory Cards and Flash Disks Jumpers LEDs PC Card Slots Serial Ports Specifications System Software Installation Prerequisites Safety Guidelines Safety Warnings Regulatory Compliance andSafety Information Regulatory Compliance and Safety Information Electrical Equipment Guidelines Telephone Wiring Guidelines Preventing Electrostatic Discharge Damage Compatibility Requirements Chassis Slot and DRAM Requirements Memory Requirements Software Prerequisites Hardware Prerequisites Microcode Requirements List of Parts and Tools Installing the RSP8 Removing the RSP8 Page Replacing the RSP8 Page Connecting a Console Terminal Connecting to the Auxiliary Port Using the Y-Cables for Console and Auxiliary Connections Restarting the System Page Page Configuring the Router for a Single RSP8 Using the EXEC Command Interpreter Configuring High System Availability HSA Active and Standby Operation HSA Implementation Methods HSA System Requirements HSA Configuration Task List Specifying the Default Standby RSP Ensuring that Both RSPs Contain the Same Configuration Files Ensuring that Both RSPs Contain the Same System Image Ensuring that Both RSPs Contain the Same Microcode Image Page Specifying Different Startup Images for the Active and the Standby RSPs Upgrading to a New Software Version Example Figure8 Software Error ProtectionUpgrading to a New Software Version following command: Release 12.0(22.3)S1 system image from a TFTP server to slot 0 on the active RSP: Backing Up with an Older Software Version Example Route Switch Processor (RSP8) Installation and Configuration Guide OL-4920-02 Configuring High System Availability In this scenario, we begin with the configuration shown inFigure 9. Figure9 Software Error ProtectionBacking Up with an Older Software Version, Part I Figure10 Software Error ProtectionBacking Up with an Older Software Version, Part II Next,we copy the rsp-pv-mz.120-23.S image to the active and the standby RSPs, as shown in Figure 10. Last,we delete the rsp-pv-mz.120-22.3.S1 image from the standby RSP4/4+ card, as shown in Figure 11: Figure11 Software Error ProtectionBacking Up with an Older Software Version, Part III Complete the following steps to configure software error protection for this sample scenario: 0 on the active and standby RSPs: and standby RSPs: Setting Environment Variables on the Active and the Standby RSPs Manually Setting Environment Variables on the Standby RSP Automatically Setting Environment Variables on the Standby RSP Monitoring and Maintaining HSA Operation Enabling High Availability Features High Availability Feature Overview Page Hardware and Software Prerequisites Installation Procedures Enabling the Router Copying an Image onto an RSP Page Setting the Config-Register Boot Variable Configuring RPR and RPR+ Page Verifying RPR and RPR+ Use the show redundancycommand to verify that RPR or RPR+ is enabled: Configuring RPR and RPR+ Example Configuring a Stateful Switchover (SSO) Configuring Frame Relay Autosynchronization LMI Sequence Numbers Verifying SSO Note The output of these commands will vary based on your device configuration and system site requirements. Step1 Use the show redundancy command to verify that SSO is configured on the device. Step2 Run the show redundancy states command to verify that SSO is operating on the device. registered as SSO protocols or applications. Verify the list of supported line protocols. Configuring Nonstop Forwarding (NSF) Configuring CEF NSF Configuring BGP NSF Configuring OSPF NSF Configuring IS-IS NSF Verifying CEF NSF Verifying BGP NSF Verifying OSPF NSF Verifying IS-IS NSF Page Troubleshooting NSF Features NSF Troubleshooting Tips BGP NSF Configuration Example BGP NSF Neighbor Device Configuration Example OSPF NSF Configuration Example IS-IS NSF Configuration Example Performing a Fast Software Upgrade Page Fast Software Upgrade Example Configuring SLCR Enabling SLCR Disabling SLCR Verifying Cisco 7500 SLCR SLCR Configuration Example RPR, RPR+, SSO, and FSU Troubleshooting Tips Monitoring and Maintaining the Active and Standby RSPs Troubleshooting the Installation Verifying LEDs System Power LEDs RSP8 LEDs Verifying System Startup Sequence Page Troubleshooting a Router That is Failing to Boot Troubleshooting a Failed RSP8 Troubleshooting RSP Boot Errors During OIR of an Interface Processor Reloading a Failed RSP Displaying a Stack Trace of an RSP Maintenance Information Saving and Retrieving a Configuration File Using the ping Command to Ensure Connectivity Copying the Configuration File Page Retrieving the Configuration File Replacing and Upgrading DRAM DIMMs Page Removing DIMMs Installing New DIMMs Checking the RSP Memory Upgrade Recovering a Lost Password Page Reference Information Console Port Signals Auxiliary Port Signals Console and Auxiliary Y-Cable Pinouts Software Configuration Register Settings Page Changing Settings Bit Meanings Page Enabling a Boot from Flash Memory Enabling a Boot from the Flash Disk Using Flash Memory Obtaining Documentation Cisco.com Documentation CD-ROM Ordering Documentation Documentation Feedback Obtaining Technical Assistance Cisco TAC Website Opening a TAC Case TAC Case Priority Definitions Obtaining Additional Publications and Information