Bootflash | Cisco Systems RSP8 guide

Configuring High System Availability

Figure 8 illustrates the software error protection configuration for this sample scenario. The commands to set up this configuration follow the figure.

Figure 8 Software Error Protection—Upgrading to a New Software Version

NAL

NAL

ENABLE

A

LL ANBAE

ANBAE AL

EE

A

LL
ANBAE
ANB	AE

AL
EE

A

ENABLE

NLE

NLE

Step 1 To verify the location and version of the software image on the active RSP’s PC Card in slot 0, use the following command:

Router# show			slot0:
-#- ED		----type----		--crc--- -	seek--	nlen	-length- -----	date/time------	name
1	..	image		FEC9823F	AF0424	18	11203868 Jan 24 2000 23:26:33		rsp-pv-mz.120-23.S

Step 2 Now view the standby software image location and version:

Router# show			bootflash:
-#- ED		----type----		--crc--- -	seek--	nlen	-length- -----	date/time------	name
1	..	image		FEC9823F	AF0424	18	11203868 Jan 24 2000 23:26:33		rsp-pv-mz.120-23.S

Step 3 To upgrade to the Cisco IOS Release 12.0(22.3)S1 system image on the active RSP, copy the Cisco IOS Release 12.0(22.3)S1 system image from a TFTP server to slot 0 on the active RSP:

Router# copy tftp slot0:rsp-pv-mz.120-22.3.S1

Route Switch Processor (RSP8) Installation and Configuration Guide

34	OL-4920-02

Image 34

Cisco Systems RSP8 manual Now view the standby software image location and version, Bootflash

Contents

Document Contents Related Documentation Cisco.com, Obtaining Documentation, Product Description Topics discussed in this section are Monitoring interface and environmental status RSP8-Horizontal Front-Panel View Flash Eprom ROMmon Bus connectors Auxiliary port U12 Shows the memory components on the RSP8 Memory ComponentsType Size Quantity Description Location LEDs There are no user-configurable jumpers on the RSP8Jumpers Flash Memory Cards and Flash Disks Serial Ports PC Card SlotsLED Label Color State Indication Specifications SpecificationsLists the physical specifications for the RSP8 System Software Safety Guidelines Installation PrerequisitesSafety Warnings Installation Prerequisites Electrical Equipment Guidelines Telephone Wiring GuidelinesPreventing Electrostatic Discharge Damage Chassis Slot and Dram Requirements Compatibility RequirementsMemory Requirements Software Prerequisites Hardware Prerequisites List of Parts and Tools Microcode Requirements Installing the RSP8 Removing the RSP8 Ejector Levers and Captive Installation Screw Replacing the RSP8 Handling the RSP8 During Removal and Installation Connecting to the Auxiliary Port Connecting a Console TerminalUsing the Y-Cables for Console and Auxiliary Connections Restarting the System Shows the console Y-cable and shows the auxiliary Y-cable Installing the RSP8 Router show version Configuring the Router for a Single RSP8 Using the Exec Command Interpreter Configuring High System Availability HSA Active and Standby Operation HSA Implementation Methods HSA Configuration Task List HSA System Requirements Router# configure terminal Specifying the Default Standby RSPCommand Purpose Router# copy system running-config nvramstartup-config Ensuring that Both RSPs Contain the Same System Image Ensuring that Both RSPs Contain the Same Microcode Image Router# show controller cbus Router# copy bootflashfilename slot0filename Router# dir slavebootflash slaveslot0 slaveslot1Slot1filename slavebootslotfilename Determines whether the standby RSP contains the same Router# copy source bootflash slot0 slot1Copies a different system image to the active RSP Upgrading to a New Software Version Example Now view the standby software image location and version BootflashRouter# copy tftp slot0rsp-pv-mz.120-22.3.S1 Routerconfig# config-register 0x010F Routerconfig# boot system tftp rsp-pv-mz.120-23.SBacking Up with an Older Software Version Example ANB Delete the rsp-pv-mz.120-22.3.S1image from the standby RSP Router# show bootflashRouter# delete slaveslot0rsp-pv-mz.120-22.3.S1 Manually Setting Environment Variables on the Standby RSP Router# copy system running-config startup-config Router# copy running-config startup-config Routerconfig# slave sync config Information under that RSP’s ROM monitor control Routerconfig# hw-module slot imageMonitoring and Maintaining HSA Operation Specifies which image the standby runs High Availability Feature Overview Enabling High Availability FeaturesRouter# slave sync config Enabling High Availability Features Installation Procedures Hardware and Software Prerequisites Enabling the Router This completes the procedure to enable the routerCopying an Image onto an RSP Router# copy tftp slot slot-number Router# copy tftp slaveslot slot-number Routerconfig# boot system flash Setting the Config-Register Boot VariableConfiguring RPR and RPR+ Router# show version Routerconfig# hw-module slot slot-numberimage file-spec Router# hw-module sec-cpu reset Verifying RPR and RPR+ Configuring RPR and RPR+ ExampleRouter# show redundancy Configuring a Stateful Switchover SSO Configuration file Saves the configuration changes to the startupVerifying SSO Router# show redundancy states my state = 13 -ACTIVE Router# show redundancy client Configuring CEF NSF Configuring Nonstop Forwarding NSFConfiguring BGP NSF As-number Configuring Ospf NSFConfiguring IS-IS NSF Graceful-restart Verifying CEF NSF Seconds adjacency Verifying BGP NSF Router# show ip bgp neighbors Verifying Ospf NSF Running-config commandThis example, note the presence of NSF restart enabled Verifying IS-IS NSF Networking device Troubleshooting NSF Features NSF Troubleshooting Tips Ospf NSF Configuration Example BGP NSF Configuration ExampleBGP NSF Neighbor Device Configuration Example IS-IS NSF Configuration Example Performing a Fast Software Upgrade Specifies the image to be used by the standby RSP at Routerconfig# hw-module slot slot-number imageName of the image of the standby RSP Router# redundancy force-switchover Configuring SlcrFast Software Upgrade Example Routerconfig# service single-slot-reload-enable Slcr Troubleshooting Tips RPR, RPR+, SSO, and FSU Troubleshooting TipsSlcr Configuration Example Disabling Slcr Monitoring and Maintaining the Active and Standby RSPs Troubleshooting the InstallationSystem Power LEDs Verifying LEDs RSP8 LEDs Normal Verifying System Startup Sequence Troubleshooting the Installation Troubleshooting a Router That is Failing to Boot Troubleshooting a Failed RSP8 Reloading a Failed RSP Maintenance InformationSaving and Retrieving a Configuration File Displaying a Stack Trace of an RSP Using the ping Command to Ensure Connectivity Router# ping Might include the name or address of a default file server Copying the Configuration FileSection on page 24 to enable the privileged level Copy to this file Router# show startup-config Retrieving the Configuration File Replacing and Upgrading Dram DIMMs Product Numbers Quantity Dram Sockets Totals Sdram Dimm Removing DIMMs Polarization notch Installing New DIMMs Inserting the Dimm Recovering a Lost Password Checking the RSP Memory Upgrade Initialize the router using the i command as follows Pin Signal Direction Description Console Port SignalsReference Information Female DB-25 Pins Male DB-25 Pins Signal Description Auxiliary Port SignalsConsole and Auxiliary Y-Cable Pinouts P1-5 J1-5 and J2-5 Software Configuration Register SettingsMale DB-25 Pins Female DB-25 Pins Signal Description P1-7 J1-7 and J2-7 Ground P1-8 J1-8 and J2-8 Boots the first system image in onboard Flash memory Boot Field MeaningStays at the system bootstrap prompt Bit Number Hexadecimal Meaning Bit Meanings Changing SettingsRouterconfig# config-register 0xvalue Tftp flash filename Action/Filename Bit Bit Address net host Enabling a Boot from Flash MemoryRouterconfig# boot system flash devicefilename Baud Bit Enabling a Boot from the Flash Disk Obtaining Documentation Using Flash MemorySystem# copy running-config startup-config Cisco.com Ordering Documentation Obtaining Technical AssistanceDocumentation CD-ROM Documentation Feedback Cisco TAC Website Opening a TAC Case TAC Case Priority Definitions Obtaining Additional Publications and Information Copyright 2004 Cisco Systems, Inc. All rights reserved