Appendix B– Configuration Record Sheet, Continued

2c. General Flow Configuration Section

 

 

 

 

 

 

PV4 Range:

LRV ________

 

URV ________

URL ________

 

(defaults are 0, 100,000 and 100,000 m3/hr)

 

 

 

 

 

PV4 Eng. Units:

cc/h ___

 

cc/min ___

 

l/h ___

l/min ___

 

(Volumetric Flow)

gal/day ___

 

Kgal/day ___

gal/h ___

gal/min ___

 

 

bbl/day ___

 

m3/day ___

m3/hr ___

m3/min ___

 

 

m3/sec ___

 

CFM ___

 

CFH ___

 

 

Type of Volumetric Flow Units:

 

 

 

 

 

 

Standard Volume Units ____

Actual Volume Units ____

 

 

 

PV4 Eng. Units:

lb/min ___

 

lb/h ___

 

lb/sec ___

ton/sec ___

 

(Mass Flow)

ton/min ___

 

ton/h ___

 

kg/min ___

kg/sec ___

 

 

kg/h ___

 

t/min ___

 

t/h ___

t/sec ___

 

 

g/sec ___

 

g/min ___

 

g/h ___

 

 

PV4 Eng. Units:

____ ____ ____ ____ ____ ____ ____ ____

Conversion Factor = ______________

 

(Complete if choosing Custom Units, 8 characters Max.)

 

 

 

 

PV4 Damping (sec.):

0.0 ___

0.5 ___

1.0 ___

2.0 ___

3.0 ___

4.0 ___

 

 

5.0 ___

10 ___

50 ___

100 ___

 

 

 

PV4 Low Flow Cutoff:

Low Limit ________

High Limit ________

(defaults are zero)

 

PV4 Failsafe:

PV2 Failsafe On ___

PV2 Failsafe Off ___

 

Pressure ________

 

 

PV3 Failsafe On ___

PV3 Failsafe Off ___

 

Temperature _______

 

Configured By:

___________________________

 

Date:

___/___/___

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Custom Fluids -

Liquid Applications - If you are using a custom fluid that is not listed in the SCT 3000 Flow Compensation Wizard, you can supply values for density vs. temperature and viscosity vs. temperature in the flow equation (if dynamic compensation is desired). If dynamic compensation is not desired, enter the density and viscosity values at normal flowing conditions.

Density – lbs/ft3

 

viscosity – cPoise

temperature – deg. F

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Gas and Steam Applications - If you are using a custom gas that is not listed in the SCT 3000 Flow Compensation Wizard, you can supply values for viscosity vs. temperature in the flow equation (if dynamic viscosity is desired). If dynamic compensation is not desired, enter the viscosity values at normal flowing conditions.

 

 

viscosity – cPoise

temperature – deg. F

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

174

SMV 3000 Transmitter User’s Manual

1/99

Page 186
Image 186
Honeywell user manual SMV 3000 Transmitter User’s Manual