Access Control Screen | HP 100 Router specs

58CHAPTER 5: ROUTER CONFIGURATION

To configure Access Control, do the following:

1Select Firewall from the main menu, then select Client IP Filters from the sub-menu, and make sure the Access Control tab is selected. The Access Control screen displays (Figure 37).

Figure 37 Access Control Screen

2At the Enable Filtering Function radio buttons, select Enable or Disable to enable or disable all Access Control rules.

3Click Apply to save the settings.

Image 58

HP 100 Router manual Access Control Screen

Contents

OfficeConnect Cable/DSL Router User Guide 3Com Corporation Campus Drive Marlborough, MA USA Contents Running the Setup Wizard Troubleshooting ISP Information Technical Specifications About this Guide Document to 3Com at ConventionsPddtechpubscomments@3com.com Configure your Router About this Guide OfficeConnect Cable/DSL Router Example Network Without a Router Router Advantages Operations Minimum System Component RequirementsFront Panel Alert LED Orange Four LAN Status LEDs Power LED GreenIndicates that the Router is powered on Cable/DSL Status LED Rear Panel Positioning the Router Safety InformationIntroduction Including Router ConnectingWall Mounting Computer, do the following Connecting the Router Hardware Installation Automatically Obtaining an IPAddress This chapter Restart your computer Local Area Properties Screen Obtaining an IP Address Automatically Software Proxy Refer to for details on how to do this AccessingTo use the Setup Wizard Wizard Login screen displays Figure Router Login Screen Admin Password screen Figure Click Next to display the Time Zone setup screen Figure Running the Setup Wizard Click Next to display the Connection Type screen Dynamic IP Address Mode Click Next. The DNS screen displays. Refer to DNS on PPPoE Mode PPPoE Interface Screen Pptp Mode L2TP L2TP Screen Static IP Mode Static IP Mode Screen DNS DNS Screen Address LAN Configuration Dhcp Server Parameters Summary Through the Router ConfigurationNavigating Pages LAN Settings LAN Settings screen Dynamic IP Address DSL or Cable Dhcp Clients ListPPPoE DSL only L2TP DSL or Cable Pptp DSL or CableStatic IP Address DSL or Cable Check all of your settings and then click Apply Dynamic IP Address Internet Settings PPPoE Interface Screen PPPoE Pptp Check with your ISP to make sure they support L2TP Internet Settings Static IP Screen Static IP Address Internet Settings DNS Screen Firewall Configure the following firewall functionsSPI Stateful Packet Inspection SPI inspects packets at See DMZ on Intrusion Detection Feature SPI Screen upper section Alert by E-mail Stateful Packet InspectionConnection Policy DoS Detect Criteria Special Application Screen Virtual Server Screen Access Control Virtual Server Add/Edit Screen Access Control Screen To control access to specific Internet services URL Filter Schedule Rule URL Filter Screen Firewall Schedule Rule Add Rule Screen MAC Address Filtering VPN Operation VPN IPSec must be enabled if you want to use L2TP over IPSec VPN Tunnel Configuration IPSec Screen Connection IKE Keep Alive feature is not available IPSec Connection IPSec connection VPN Tunnel Configuration L2TP over IPSec Screen VPN Tunnel Configuration Pptp Screen Select Enable to activate Snmp Agent installedSnmp Simple Network Management Protocol allows remote System Tools Restart Router Screen Click Reset Changed Click Save to save your current configuration settings Saving a configuration fileRestoring a configuration file Upgrade Screen To change the password Admin Password Screen Time Zone Screen Advanced To disable NAT, select the OFF radio button Advanced Advanced Static Route Static Route screen RIP RIP screen Routing Table Routing Table screen Select the Dynamic DNS Enable radio button TZO.com DynDNS Status and LogsAlso displays two sub-menus Traffic Metering and Logs To view the Traffic Metering screen Traffic Metering Screen Logs Screen Support Screen Basic Connection Browsing to the Router Configuration ScreensChecks Connecting to Internet Seconds and then re-apply power. If the Alert LED comes on Fault with the hardware. Remove power from the Router, waitAlert LED Power Adapter OK Power LED orLED Not Lit Latest software is available on 3Com’s Web site at Where can I download software updates for the Router? Frequently Asked QuestionsHow do I reset the Router to Factory Defaults? How many computers on the LAN does the Router support? Frequently Asked Questions Troubleshooting Internet protocol suite consists of a well-defined set Protocol SuiteManaging the Router over the Network TCP working together. TCP/IP is an internationally adopted Type One Type Two How does a Device Obtain an IP Address and Subnet Mask? Appendix a IP Addressing ISP Information Information Regarding Popular ISPs Drizzle, DSL Extreme, Earthlink OfficeConnect Cable/DSL Router System Requirements Operating Systems Safety Information Important Safety Information Wichtige Sicherheitshinweise Consignes importantes de Información de seguridad Register Your Product to Gain Service BenefitsServices Purchase Contact Us Access SoftwareDownloads Telephone Technical Telephone Technical Support and Repair Latsupportanc@3com.com Agreement Appendix F END User Software License Agreement Glossary Glossary Ethernet Address See MAC address Glossary Glossary Traffic The movement of data packets on a network Glossary Glossary Index Index Regulatory Notices Page Page DUA8589-1AAA01 Rev