Address | HP 100 Router instruction

36CHAPTER 4: RUNNING THE SETUP WIZARD

Hostname and MAC Figure 20 Hostname and MAC Address Screen

Address

1Some ISPs require a host name. If your ISP has this requirement, enter the host name in the Host Name text box.

2Either:

■If your ISP requires an assigned MAC address, enter the values for a MAC address. Or,

■If the computer you are now using is the one that was previously connected directly to the cable modem, select Clone. Or,

■To reset the MAC Address to the default, select Reset MAC.

3Click Next to display the LAN Settings screen.

Image 36

HP 100 Router manual Address

Contents

OfficeConnect Cable/DSL Router User Guide 3Com Corporation Campus Drive Marlborough, MA USA Contents Running the Setup Wizard Troubleshooting ISP Information Technical Specifications About this Guide Conventions Document to 3Com atPddtechpubscomments@3com.com Configure your Router About this Guide OfficeConnect Cable/DSL Router Example Network Without a Router Router Advantages Minimum System Component Requirements Front PanelOperations Alert LED Orange Power LED Green Indicates that the Router is powered onFour LAN Status LEDs Cable/DSL Status LED Rear Panel Safety Information IntroductionPositioning the Router Including Connecting Wall MountingRouter Computer, do the following Connecting the Router Hardware Installation Obtaining an IP AddressAutomatically This chapter Restart your computer Local Area Properties Screen Obtaining an IP Address Automatically Software Proxy Accessing To use the Setup WizardRefer to for details on how to do this Wizard Login screen displays Figure Router Login Screen Admin Password screen Figure Click Next to display the Time Zone setup screen Figure Running the Setup Wizard Click Next to display the Connection Type screen Dynamic IP Address Mode Click Next. The DNS screen displays. Refer to DNS on PPPoE Mode PPPoE Interface Screen Pptp Mode L2TP L2TP Screen Static IP Mode Static IP Mode Screen DNS DNS Screen Address LAN Configuration Dhcp Server Parameters Summary Configuration NavigatingThrough the Router Pages LAN Settings LAN Settings screen Dhcp Clients List Dynamic IP Address DSL or CablePPPoE DSL only Pptp DSL or Cable L2TP DSL or CableStatic IP Address DSL or Cable Check all of your settings and then click Apply Dynamic IP Address Internet Settings PPPoE Interface Screen PPPoE Pptp Check with your ISP to make sure they support L2TP Internet Settings Static IP Screen Static IP Address Internet Settings DNS Screen Configure the following firewall functions FirewallSPI Stateful Packet Inspection SPI inspects packets at See DMZ on Intrusion Detection Feature SPI Screen upper section Stateful Packet Inspection Alert by E-mailConnection Policy DoS Detect Criteria Special Application Screen Virtual Server Screen Access Control Virtual Server Add/Edit Screen Access Control Screen To control access to specific Internet services URL Filter Schedule Rule URL Filter Screen Firewall Schedule Rule Add Rule Screen MAC Address Filtering VPN Operation VPN IPSec must be enabled if you want to use L2TP over IPSec VPN Tunnel Configuration IPSec Screen Connection IKE Keep Alive feature is not available IPSec Connection IPSec connection VPN Tunnel Configuration L2TP over IPSec Screen VPN Tunnel Configuration Pptp Screen Agent installed Select Enable to activate SnmpSnmp Simple Network Management Protocol allows remote System Tools Restart Router Screen Click Reset Changed Saving a configuration file Click Save to save your current configuration settingsRestoring a configuration file Upgrade Screen To change the password Admin Password Screen Time Zone Screen Advanced To disable NAT, select the OFF radio button Advanced Advanced Static Route Static Route screen RIP RIP screen Routing Table Routing Table screen Select the Dynamic DNS Enable radio button TZO.com Status and Logs DynDNSAlso displays two sub-menus Traffic Metering and Logs To view the Traffic Metering screen Traffic Metering Screen Logs Screen Support Screen Browsing to the Router Configuration Screens Basic ConnectionChecks Connecting to Internet Fault with the hardware. Remove power from the Router, wait Seconds and then re-apply power. If the Alert LED comes onAlert LED Power LED or Power Adapter OKLED Not Lit Latest software is available on 3Com’s Web site at Frequently Asked Questions How do I reset the Router to Factory Defaults?Where can I download software updates for the Router? How many computers on the LAN does the Router support? Frequently Asked Questions Troubleshooting Protocol Suite Managing the Router over the NetworkInternet protocol suite consists of a well-defined set TCP working together. TCP/IP is an internationally adopted Type One Type Two How does a Device Obtain an IP Address and Subnet Mask? Appendix a IP Addressing ISP Information Information Regarding Popular ISPs Drizzle, DSL Extreme, Earthlink OfficeConnect Cable/DSL Router System Requirements Operating Systems Safety Information Important Safety Information Wichtige Sicherheitshinweise Consignes importantes de Información de seguridad Product to Gain Service Benefits ServicesRegister Your Purchase Access Software DownloadsContact Us Telephone Technical Telephone Technical Support and Repair Latsupportanc@3com.com Agreement Appendix F END User Software License Agreement Glossary Glossary Ethernet Address See MAC address Glossary Glossary Traffic The movement of data packets on a network Glossary Glossary Index Index Regulatory Notices Page Page DUA8589-1AAA01 Rev