Accessing, To use the Setup Wizard | HP 100 Router manual

4	RUNNING THE SETUP WIZARD

Accessing the	The Router setup program is Web-based, which means that it is accessed
Wizard	through your Web browser (Netscape Navigator or Internet Explorer).
	To use the Setup Wizard:
1	Ensure that you have at least one computer connected to the Router.
	Refer to Chapter 2 for details on how to do this.
2	Launch your Web browser on the computer.
3	Enter the following URL in the location or address field of your browser:
	http://192.168.1.1 (as shown in Figure 9).

Figure 9 Web Browser Location Field (Factory Default)

Image 25

HP 100 Router manual Accessing, To use the Setup Wizard, Refer to for details on how to do this

Contents

OfficeConnect Cable/DSL Router User Guide 3Com Corporation Campus Drive Marlborough, MA USA Contents Running the Setup Wizard Troubleshooting ISP Information Technical Specifications About this Guide Document to 3Com at ConventionsPddtechpubscomments@3com.com Configure your Router About this Guide Cable/DSL Router OfficeConnect Example Network Without a Router Router Advantages Front Panel Minimum System Component RequirementsOperations Alert LED Orange Indicates that the Router is powered on Power LED GreenFour LAN Status LEDs Cable/DSL Status LED Rear Panel Introduction Safety InformationPositioning the Router Including Wall Mounting ConnectingRouter Computer, do the following Connecting the Router Hardware Installation Address Obtaining an IPAutomatically This chapter Local Area Properties Screen Restart your computer Obtaining an IP Address Automatically Proxy Software To use the Setup Wizard AccessingRefer to for details on how to do this Wizard Router Login Screen Login screen displays Figure Click Next to display the Time Zone setup screen Figure Admin Password screen Figure Running the Setup Wizard Click Next to display the Connection Type screen Click Next. The DNS screen displays. Refer to DNS on Dynamic IP Address Mode PPPoE Interface Screen PPPoE Mode L2TP Pptp Mode L2TP Screen Static IP Mode Screen Static IP Mode DNS DNS Screen Address Dhcp Server Parameters LAN Configuration Summary Navigating ConfigurationThrough the Router Pages LAN Settings LAN Settings screen Dynamic IP Address DSL or Cable Dhcp Clients ListPPPoE DSL only L2TP DSL or Cable Pptp DSL or CableStatic IP Address DSL or Cable Dynamic IP Address Check all of your settings and then click Apply PPPoE Internet Settings PPPoE Interface Screen Pptp Check with your ISP to make sure they support L2TP Static IP Address Internet Settings Static IP Screen Internet Settings DNS Screen Firewall Configure the following firewall functionsSPI Stateful Packet Inspection SPI inspects packets at See DMZ on SPI Screen upper section Intrusion Detection Feature Alert by E-mail Stateful Packet InspectionConnection Policy DoS Detect Criteria Special Application Screen Virtual Server Screen Virtual Server Add/Edit Screen Access Control Access Control Screen URL Filter To control access to specific Internet services URL Filter Screen Schedule Rule Firewall Schedule Rule Add Rule Screen MAC Address Filtering Operation VPN VPN IPSec must be enabled if you want to use L2TP over IPSec Connection VPN Tunnel Configuration IPSec Screen IPSec Connection IPSec connection IKE Keep Alive feature is not available VPN Tunnel Configuration L2TP over IPSec Screen VPN Tunnel Configuration Pptp Screen Select Enable to activate Snmp Agent installedSnmp Simple Network Management Protocol allows remote System Tools Restart Router Screen Changed Click Reset Click Save to save your current configuration settings Saving a configuration fileRestoring a configuration file Upgrade Screen Admin Password Screen To change the password Time Zone Screen Advanced Advanced To disable NAT, select the OFF radio button Advanced Static Route screen Static Route RIP RIP screen Routing Table screen Routing Table TZO.com Select the Dynamic DNS Enable radio button DynDNS Status and LogsAlso displays two sub-menus Traffic Metering and Logs Traffic Metering Screen To view the Traffic Metering screen Logs Screen Support Screen Basic Connection Browsing to the Router Configuration ScreensChecks Internet Connecting to Seconds and then re-apply power. If the Alert LED comes on Fault with the hardware. Remove power from the Router, waitAlert LED Power Adapter OK Power LED orLED Not Lit Latest software is available on 3Com’s Web site at How do I reset the Router to Factory Defaults? Frequently Asked QuestionsWhere can I download software updates for the Router? How many computers on the LAN does the Router support? Frequently Asked Questions Troubleshooting Managing the Router over the Network Protocol SuiteInternet protocol suite consists of a well-defined set TCP working together. TCP/IP is an internationally adopted Type Two Type One How does a Device Obtain an IP Address and Subnet Mask? Appendix a IP Addressing Information Regarding Popular ISPs ISP Information Drizzle, DSL Extreme, Earthlink OfficeConnect Cable/DSL Router System Requirements Operating Systems Important Safety Information Safety Information Wichtige Sicherheitshinweise Consignes importantes de Información de seguridad Services Product to Gain Service BenefitsRegister Your Purchase Downloads Access SoftwareContact Us Telephone Technical Telephone Technical Support and Repair Latsupportanc@3com.com Agreement Appendix F END User Software License Agreement Glossary Glossary Ethernet Address See MAC address Glossary Glossary Traffic The movement of data packets on a network Glossary Glossary Index Index Regulatory Notices Page Page DUA8589-1AAA01 Rev