OfficeConnect Cable/DSL Router | HP 100 Router manual

C	TECHNICAL SPECIFICATIONS

This section lists the technical specifications for the OfficeConnect

Cable/DSL Router.

OfficeConnect Cable/DSL Router

Standards

Interfaces

Cable/DSL modem connection — 10 Mbps/100 Mbps dual speed Ethernet port (10BASE-T/100BASE-TX)

LAN connection — four 10Mbps/100Mbps dual speed Ethernet ports (10BASE-T/100BASE-TX)

Operating Temperature

0 °C to 40 °C (32 °F to 105 °F)

Power

7VA, 23.9 BThU/hr

Humidity

0 % to 90 % (non-condensing) humidity

Dimensions

■Width = 220 mm (8.7 in.)

■Depth = 135.4 mm (5.2 in.)

■Height = 24.2 mm (1 in.)

Weight

535 g (1.3 lb)

Functional: ISO 8802/3

IEEE 802.3

Image 105

HP 100 Router manual OfficeConnect Cable/DSL Router

Contents

OfficeConnect Cable/DSL Router User Guide 3Com Corporation Campus Drive Marlborough, MA USA Contents Running the Setup Wizard Troubleshooting ISP Information Technical Specifications About this Guide Conventions Document to 3Com atPddtechpubscomments@3com.com Configure your Router About this Guide Cable/DSL Router OfficeConnect Example Network Without a Router Router Advantages Front Panel Minimum System Component RequirementsOperations Alert LED Orange Indicates that the Router is powered on Power LED GreenFour LAN Status LEDs Cable/DSL Status LED Rear Panel Introduction Safety InformationPositioning the Router Including Wall Mounting ConnectingRouter Computer, do the following Connecting the Router Hardware Installation Address Obtaining an IPAutomatically This chapter Local Area Properties Screen Restart your computer Obtaining an IP Address Automatically Proxy Software To use the Setup Wizard AccessingRefer to for details on how to do this Wizard Router Login Screen Login screen displays Figure Click Next to display the Time Zone setup screen Figure Admin Password screen Figure Running the Setup Wizard Click Next to display the Connection Type screen Click Next. The DNS screen displays. Refer to DNS on Dynamic IP Address Mode PPPoE Interface Screen PPPoE Mode L2TP Pptp Mode L2TP Screen Static IP Mode Screen Static IP Mode DNS DNS Screen Address Dhcp Server Parameters LAN Configuration Summary Navigating ConfigurationThrough the Router Pages LAN Settings LAN Settings screen Dhcp Clients List Dynamic IP Address DSL or CablePPPoE DSL only Pptp DSL or Cable L2TP DSL or CableStatic IP Address DSL or Cable Dynamic IP Address Check all of your settings and then click Apply PPPoE Internet Settings PPPoE Interface Screen Pptp Check with your ISP to make sure they support L2TP Static IP Address Internet Settings Static IP Screen Internet Settings DNS Screen Configure the following firewall functions FirewallSPI Stateful Packet Inspection SPI inspects packets at See DMZ on SPI Screen upper section Intrusion Detection Feature Stateful Packet Inspection Alert by E-mailConnection Policy DoS Detect Criteria Special Application Screen Virtual Server Screen Virtual Server Add/Edit Screen Access Control Access Control Screen URL Filter To control access to specific Internet services URL Filter Screen Schedule Rule Firewall Schedule Rule Add Rule Screen MAC Address Filtering Operation VPN VPN IPSec must be enabled if you want to use L2TP over IPSec Connection VPN Tunnel Configuration IPSec Screen IPSec Connection IPSec connection IKE Keep Alive feature is not available VPN Tunnel Configuration L2TP over IPSec Screen VPN Tunnel Configuration Pptp Screen Agent installed Select Enable to activate SnmpSnmp Simple Network Management Protocol allows remote System Tools Restart Router Screen Changed Click Reset Saving a configuration file Click Save to save your current configuration settingsRestoring a configuration file Upgrade Screen Admin Password Screen To change the password Time Zone Screen Advanced Advanced To disable NAT, select the OFF radio button Advanced Static Route screen Static Route RIP RIP screen Routing Table screen Routing Table TZO.com Select the Dynamic DNS Enable radio button Status and Logs DynDNSAlso displays two sub-menus Traffic Metering and Logs Traffic Metering Screen To view the Traffic Metering screen Logs Screen Support Screen Browsing to the Router Configuration Screens Basic ConnectionChecks Internet Connecting to Fault with the hardware. Remove power from the Router, wait Seconds and then re-apply power. If the Alert LED comes onAlert LED Power LED or Power Adapter OKLED Not Lit Latest software is available on 3Com’s Web site at How do I reset the Router to Factory Defaults? Frequently Asked QuestionsWhere can I download software updates for the Router? How many computers on the LAN does the Router support? Frequently Asked Questions Troubleshooting Managing the Router over the Network Protocol SuiteInternet protocol suite consists of a well-defined set TCP working together. TCP/IP is an internationally adopted Type Two Type One How does a Device Obtain an IP Address and Subnet Mask? Appendix a IP Addressing Information Regarding Popular ISPs ISP Information Drizzle, DSL Extreme, Earthlink OfficeConnect Cable/DSL Router System Requirements Operating Systems Important Safety Information Safety Information Wichtige Sicherheitshinweise Consignes importantes de Información de seguridad Services Product to Gain Service BenefitsRegister Your Purchase Downloads Access SoftwareContact Us Telephone Technical Telephone Technical Support and Repair Latsupportanc@3com.com Agreement Appendix F END User Software License Agreement Glossary Glossary Ethernet Address See MAC address Glossary Glossary Traffic The movement of data packets on a network Glossary Glossary Index Index Regulatory Notices Page Page DUA8589-1AAA01 Rev