1 PANEL DESCRIPTION

■Front panel (continued)

#3

#4#5

#6 #7 #8

#9

$0

$1

 

$2

 

 

 

TX

RX

 

SPLIT

LOCK

 

 

 

 

 

TWIN-PBT

NSCEIVER

 

 

 

 

1.8

3.5

7

 

 

 

 

 

 

 

 

 

 

 

700

 

 

 

 

 

 

 

 

 

1

2

3

FILTER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

14

18

 

 

 

 

 

 

 

 

 

 

 

4

5

6

 

ONITOR

 

 

 

 

 

 

 

 

 

21

24

28

PBT-CLR

 

 

 

 

 

 

 

 

 

 

 

D DELAY

 

 

 

 

 

 

 

 

 

7

8

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GENE

50

F-INP

DIGI-SEL NOTCH

 

 

 

 

 

 

 

 

 

 

 

0

ENT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DIGI-SEL

 

 

 

 

 

 

 

 

 

 

 

MP-W

MP-R

 

 

 

 

 

 

 

 

 

 

 

 

MW

V/M

APF/TPF

 

 

 

 

 

 

 

 

 

 

 

 

NB

 

 

 

 

 

 

 

 

 

 

 

 

NOTCH

 

 

 

 

 

 

 

 

 

 

A/B

A=B

 

 

 

 

 

 

 

 

 

 

 

 

 

TS

RIT/∂TX

 

 

 

 

 

 

 

 

 

 

 

 

RIT

 

 

 

 

 

 

 

 

 

 

XFC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

∂TX

 

 

 

 

 

 

 

 

 

 

 

 

 

CLEAR

NB

 

 

 

 

 

 

 

 

 

 

 

 

 

RF

F-1

F-2

F-3

F-4

F-5

F-6

 

F-7

 

 

 

 

CW PITCH

 

 

 

 

 

SPEECH

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SSB

CW

RTTY/PSK

AM/FM

DATA

M.SCOPE

EXIT/SET

AUTO

 

 

LOCK

 

TUNE

 

 

 

 

 

 

 

 

 

REC

PLAY

 

 

 

 

SPLIT

 

 

 

 

 

 

 

 

 

 

 

 

DRIVE

COMP

MONI GAIN

VOX GAIN

ANTI VOX

CONTRAST

BRIGHT

VOICE MEMORY

 

 

 

 

 

#3MULTI-FUNCTION SWITCHES

Push to select the functions indicated in the LCD display to the right of these switches.

• Functions vary depending on the operating condition.

MF1 (MULTI-FUNCTION 1 SWITCH)

ANT

➥ Selects the antenna connector from

1ANT1, ANT2, ANT3 and ANT4 when pushed. (p. 10-2)

➥Displays antenna selection memory when pushed and held for 1 sec.

•When the receive antenna is activated, the antenna connected to [ANT4] is used for receive only.

When a transverter is in use, this [ANT] does not function and ‘TRV’ appears.

MF2 (MULTI-FUNCTION 2 SWITCH)

METER

 

➥ Selects RF power (Po), SWR, ALC,

 

 

COMP, VD or ID metering during trans-

Po

 

 

 

mit. (p. 3-10)

➥Switches the multi-function digital meter ON and OFF when pushed and held for 1 sec. (p. 3-10)

MF3 (MULTI-FUNCTION 3 SWITCH)

P.AMP

➥ Selects one of 2 receive RF preamps

1or bypasses them. (p. 5-9)

•“P. AMP1” activates 10 dB preamp.

•“P. AMP2” activates 16 dB high-gain pre- amp.

✔What is the preamp?

The preamp amplifies signals in the receiver front end to improve S/N ratio and sensitivity. Select “P. AMP1” or “P. AMP2” when receiving weak signals..

MF4 (MULTI-FUNCTION 4 SWITCH)

ATT

➥ Selects 6 dB, 12 dB or 18 dB attenua-

tor when pushed. (p. 5-9)

OFF

➥Turns the attenuator function OFF when pushed and held for 1 sec. (p. 5-9)

✔What is the attenuator?

The attenuator prevents a desired signal from being distorted when very strong signals are near the desired fre- quency, or when very strong electromagnetic fields, such as from a broadcasting station, are near your location.

1-6