1 PANEL DESCRIPTION

■Front panel (continued)

 

 

TX

RX

 

SPLIT

LOCK

 

 

 

TWIN-PBT

 

 

 

1.8

3.5

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

2

3

FILTER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10

14

18

 

 

 

 

 

 

 

 

 

4

5

6

 

 

 

 

 

 

 

 

 

21

24

28

PBT-CLR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

8

9

 

 

 

 

 

 

 

 

 

GENE

50

F-INP

DIGI-SEL NOTCH

 

 

 

 

 

 

 

 

 

0

ENT

 

 

 

 

 

 

 

 

 

 

 

 

DIGI-SEL

 

 

 

 

 

 

 

 

 

MP-W

MP-R

 

 

 

 

 

 

 

 

 

 

MW

V/M

APF/TPF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NOTCH

 

 

 

 

 

 

 

 

 

A/B

A=B

 

 

 

 

 

 

 

 

 

 

 

TS

RIT/∂TX

 

 

 

 

 

 

 

 

 

 

RIT

 

 

 

 

 

 

 

 

XFC

 

 

 

 

 

 

 

 

 

 

 

 

 

∂TX

 

 

 

 

 

 

 

 

 

 

 

CLEAR

 

F-1

F-2

F-3

F-4

F-5

F-6

F-7

 

 

 

CW PITCH

 

 

 

 

SPEECH

 

 

 

 

 

 

 

 

 

 

 

 

SSB

CW

RTTY/PSK

AM/FM

DATA

M.SCOPE

EXIT/SET

AUTO

 

 

LOCK

 

TUNE

 

 

 

 

 

 

 

 

 

REC PLAY

 

 

 

SPLIT

 

 

 

 

 

 

 

 

 

 

 

DRIVE

COMP

MONI GAIN

VOX GAIN

ANTI VOX

CONTRAST

BRIGHT

VOICE MEMORY

 

 

 

 

^

^

^

^

^

^

^

^

&1&0 ^9

^1PASSBAND TUNING CONTROLS [TWIN-PBT] (p. 5-12)

Adjusts the receiver’s IF filter “passband width” via the DSP.

•Passband width and shift frequency are displayed in the multi-function display.

•Push and hold PBT-CLRfor 1 sec. to clear the PBT settings.

•Adjustment range is set to half of the IF filter passband width. 25 Hz steps and 50 Hz steps are available.

✔What is the PBT control?

The PBT function electronically modifies the IF passband width to reject interference. This transceiver uses the DSP circuit for the PBT function.

PBT1

PBT2

–

+

High cut

Center

Low cut

^2PBT CLEAR SWITCH PBT-CLR(p. 5-12) Clears the PBT settings when pushed and held for 1 sec.

•The [PBT-CLR] indicator above this switch lights when PBT is in use.

^3DIGITAL RF SELECTOR SWITCH DIGI-SEL

(p. 5-18)

Turns the digital RF preselector ON and OFF.

•The [DIGI-SEL] indicator lights green when the prese- lector is in use.

^4DIGITAL RF SELECTOR CONTROL [DIGI-SEL]

(p. 5-18)

Adjusts the digital RF selector center frequency.

•The control can be reassigned as the audio peak filter adjustment (p. 12-16)

Higher frequency

Lower frequency

1-10