Chapter 4 Software Troubleshooting 43

Table 9 defines the fields on this panel and indicates the lines.

Table 9 Preferences details fields for lines (Sheet 1 of 3)

Attribute

Value

Description

 

 

 

Legend: Loop = analog/digital loop; GS = ground start; DID = DID; E&M = E&M; BRI = BRI; DPNSS

= DPNSS; VoIP = VoIP; TL = Target and DASS2. Note: PRI fields are all included under the main panel.

Auto privacy

Loop

GS

DID

E&M

BRI

 

VoIP

 

 

<check box>

Define whether one BCM450 user can select a line in use at

 

 

 

another telephone to join an existing call.

 

 

 

 

 

 

 

 

 

 

 

Full autohold

Loop

 

 

 

BRI

DPNSS

VoIP

 

 

<check box>

Enables or disables Full autohold.

 

 

 

 

 

When enabled, if a caller selects an idle line but does not dial

 

 

 

any digits, that line is automatically placed on hold if you then

 

 

 

select another line.

 

 

 

 

 

 

 

Full autohold is always in place for T1 E&M trunks because it

 

 

 

has no meaning for incoming-only T1 DID trunks.

 

 

 

 

The default setting should be changed only if Full autohold is

 

 

 

required for a specific application.

 

 

 

 

 

 

 

 

 

 

 

Aux. ringer

Loop

GS

DID

E&M

BRI

DPNSS

VoIP

TL

 

<check box>

Turn the auxiliary ringer on or off for all telephones using this

 

 

 

line.

 

 

 

 

 

 

 

 

When programmed on a line, the auxiliary ringer will ring every

 

 

 

time a call is received.

 

 

 

 

 

 

 

 

 

 

 

 

Note: When programmed only on a telephone, no ring occurs for a transferred call.

 

An auxiliary ringer can also be programmed in Services to ring for a line placed into

 

a scheduled Ringing service.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ANI Number

 

DID

E&M

 

 

 

 

 

 

<check box>

Define whether the telephone number of the caller will be

 

 

 

shown for this line.

 

 

 

 

 

 

 

For T1 E&M and T1 DID trunks connected to a DTM, this setting

 

 

 

only appears if Signaling is set to WinkStart.

 

 

 

 

The central office must deliver ANI/DNIS in DTMF mode. No

 

 

 

additional equipment is required.

 

 

 

 

 

 

 

 

 

 

 

DNIS Number

 

 

E&M

 

 

 

 

 

 

<check box>

Defines whether the digits dialed by an external caller on this

 

 

 

line will be shown.For T1 E&M trunks connected to a DTM, this

 

 

 

setting only appears if Signaling is set to WinkStart and Answer

 

 

 

mode is set to Manual.

 

 

 

 

 

 

Distinct Rings in

<read-only>

Indicates if a special ring has been assigned. See Distinct Ring

use

 

 

on the main table.

 

 

 

 

 

 

 

 

 

 

 

 

 

BCM450 Troubleshooting Guide

Page 43
Image 43
Nortel Networks BM450 manual Preferences details fields for lines Sheet 1, Auto privacy