!5 !6 !7

!8 !9

 

 

 

 

 

 

 

 

 

 

 

 

 

@

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

@

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

@

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

i

 

o

 

!

0

!1 !2 !3 !4

 

 

 

 

 

 

@

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

@

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

i PORT No.

!5ALARM NOTICE (SMTP E-MAIL)

Same as the alarm terminal numbers on the rear panel

To use the e-mail notice function, select YES.

o ALARM FUNCTION

!6SERVER ADDRESS

Set the alarm function to ON or OFF.

Specify the address of the mail server to which mail is

 

sent directly from the WJ-NT104.

!0CAMERA CH

 

Specify a camera channel to be selected when an alarm is activated.

!1CAMERA PRESET

!7SENDER NAME

Set the name of a mail sender (up to 8, alphanumeric characters lower case).

Specify a preset position for the camera when an alarm

!8Destination E-Mail address

is activated.

Specify the destination mail addresses of alarm notice

This is valid only when a camera with preset function is

recipients. Up to 16 addresses can be set.

connected.

 

 

!9Delete destination E-Mail addresses

!2DELAY TIME (per 100 msec)

Set the time from activation of an alarm to the start of recording.

!3ALARM CONTACT

Select between normally closed (NC) and normally open (NO) alarm contact.

open: Accepts an NC alarm signal

close: Accepts an NO alarm signal

!4SET button

Clicking this button saves the settings in the WJ-NT104.

Displays the list of e-mail addresses to receive alarm notices. Clicking the DELETE button will delete an address from the list.

@0ALARM NOTICE (Panasonic Protocol)

If Panasonic's special alarm receiving software* is installed, mark YES to use the alarm notice function.

*This software will be available in the near future as an option.

@1DESTINATION PORT

Specify 1818.

@2RETRY NUMBER OF TIMES

Enter the number of retries in the event that an alarm notice is undeliverable.

@3Destination IP address

Specify the IP addresses of PCs to which an alarm notice is to be sent. Up to 16 IP addresses can be set.

@4Delete destination IP addresses

Displays the list of IP addresses to receive alarm notices. Clicking the DELETE button will delete an address from the list.

45

Page 45
Image 45
Panasonic WJ-NT104 5ALARM Notice Smtp E-MAIL, 6SERVER Address, 0CAMERA CH, 1CAMERA Preset 7SENDER Name, 3ALARM Contact