qVIDEO IN (WJ-NT104)

Selects any of the four video inputs of the Interface Unit for display on the monitor. Set the monitor outputs of the Matrix Switcher to match the video inputs of the Interface Unit, referring to MATRIX SWITCHER CON- FIGURATION on page 62.

The video channels will be switched in accordance with the operating mode selected. Refer to MAIN PAGE AND CONTROLS on page 25 for a description of operating modes and to MODE SETUP on page 41 for mode setting procedures.

wCAMERA SELECT (Left window panel)

To select a camera (camera 01 to 08) connected to the WJ-SX550A Matrix Switcher. The image of the selected camera is displayed on the monitor in the previously selected input mode.

ePRESET SELECT (Left part of screen)

To move the combination camera (option) connected to the WJ-SX550A to any of 8 preset positions.

rALARM LIST

Any image before and after alarm input can be tem- porarily stored in the internal memory of the WJ-NT104. For alarm display see ALARM LIST on page 37.

tCAMERA SELECT (Bottom window panel)

To select a camera (CAMERA 1 to 128) connected to the WJ-SX550A. Select a camera number, and then click [SET] to apply it. The image of the selected cam- era is displayed on the monitor in the previously select- ed input mode.

yPRESET SELECT (Bottom window panel)

To move the combination camera (option) connected to the WJ-SX550A to any of 64 preset positions. Select a preset position number, and then click the [SET] button to move the camera to the position.

uTOUR SEQUENCE

To run the tour sequence of the WJ-SX550 matrix switcher. Select a tour sequence number, and then click the [SET] button to run the sequence.

iPROGRAM SEQUENCE

To run the program sequence of the WJ-SX550 matrix switcher. Click the [SET] button to run the assigned sequence.

oALARM ALL RESET

To reset all alarms activated in the Matrix Switcher, and return it to normal condition.

!0ZOOM

The connected combination camera (option) can be zoomed by clicking the [TELE] or [WIDE] button under ZOOM.

Clicking the [TELE] or [WIDE] button will operate the camera in telescopic or wide-angle mode for a speci- fied time, after which the mode is released automatical- ly. These modes cannot be retained by keeping the [TELE] or [WIDE] button depressed. You need to click the [TELE] or [WIDE] button again.

!1FOCUS

The connected combination camera (option) can be focused by clicking the [FAR], [NEAR] or [AUTO] but- ton under FOCUS.

Clicking the [FAR] or [NEAR] button will operate the camera in focusing mode for a specified time, after which the mode is released automatically. Clicking the [AUTO] button will automatically focus the image on the screen. Focus control cannot be retained by keep- ing the [FAR] or [NEAR] button depressed. You need to click the [FAR] or [NEAR] button again.

!2IRIS

The connected combination camera (option) can be controlled to close or open iris by clicking the [CLOSE] or [OPEN] button under IRIS.

Clicking the [OPEN] or [CLOSE] button will open or close the camera iris for a specified time, after which the operation is released automatically.

Clicking the [RESET] button on the screen will reset the iris of the displayed camera to the factory default setting. Iris control cannot be retained by keeping the [OPEN] or [CLOSE] button depressed. You need to click the [OPEN] or [CLOSE] button again.

!3AUTO PAN

The auto pan status of the connected combination camera (option) can be changed by clicking the [ON] or [OFF] button under AUTOPAN.

Note: When LOCAL is selected in the camera setup menu, auto pan is released automatically after 1 minute. When REMOTE is selected, auto pan will not be released automatically.

!4Image Display

To display the image output from the Matrix Switcher connected to the WJ-NT104 Interface Unit. Set the monitor outputs of the Matrix Switcher to match the video inputs of the Interface Unit, referring to MATRIX SWITCHER CONFIGURATION on page 62.

!5PAN/TILT

Clicking anywhere on the live image moves the con- nected combination camera (option) up and down, or to the right and left. The camera pan/tilt angle decreases as the point clicked moves closer to the image center. Clicking the image center will not move the camera. Zooming does not change the camera pan/tilt angle. Click the image repeatedly to move the camera to the desired position. You cannot pan or tilt the camera continuously by dragging on the live image.

63

Page 63
Image 63
Panasonic WJ-NT104 operating instructions 0ZOOM, 1FOCUS, 2IRIS, 3AUTO PAN, 5PAN/TILT