Paradyne 3800PLUS 4 of 3800Plus AT Commands, Description, Front Panel Branch, Dial, Busy, Tone

Models: 3800PLUS

1 192
Download 192 pages 59.34 Kb
Page 129
Image 129
(4 of 11)

COMSPHERE 3800Plus Modems

Table 13-1

(4 of 11)

3800Plus AT Commands

AT Command

 

 

Description

 

Front Panel Branch

 

 

 

Xn

Extended Result Code, Dial Tone Detect, and Busy Tone Detect

Extended Result Code:

 

Configuration Options

 

 

Configure\Edit\DTE Dialer

 

 

 

 

Dial

Busy

Dial Tone Detect:

 

 

 

Extended

Tone

Tone

Configure\Edit\

 

 

 

Result Code

Detect

Detect

Line Dialer

 

 

X0

Disable

Disable

Disable

Busy Tone Detect:

 

 

Configure\Edit\

 

 

X1

Enable

Disable

Disable

 

 

Line Dialer

 

 

X2

Enable

Enable

Disable

 

 

 

 

 

X3

Enable

Disable

Enable

 

 

 

X4

Enable

Enable

Enable

 

 

 

X5

Add/EC

Enable

Enable

 

 

 

X6

Add/V42,MNP

Enable

Enable

 

 

 

X7

Use DTE Rate

Enable

Enable

 

 

Extended Result Code

 

 

 

 

Enable. Displays all result codes listed in Appendix B except for error

 

 

 

control suffix.

 

 

 

 

Disable. Only displays OK, CONNECT, RING, NO CARRIER, ERROR.

 

 

Add/EC. Displays result codes with /EC suffix. Add/V42,MNP. Displays

 

 

 

result codes with either V.42 or MNP suffix. Use DTE Rate.

 

 

 

Displays DTE data rate instead of line rate.

 

 

Add/V42,MNP. Displays result codes with either V.42 or MNP suffix.

 

 

Use DTE Rate. Displays DTE data rate instead of line rate.

 

 

Dial Tone Detect

 

 

 

 

 

Enable. Sets the modem for dial tone detect.

 

 

 

Disable. Sets the modem for blind dialing.

 

 

 

Busy Tone Detect

 

 

 

 

 

Enable. Modem monitors for busy tone.

 

 

 

 

Disable. Modem ignores busy tone.

 

 

 

 

 

 

 

 

Yn

Long Space Disconnect

 

 

Configure\Edit\

 

Y0

Disable. Ignores long space.

 

 

Line Dialer

 

Y1

Enable. Disconnects if long space is detected. Enables

 

 

 

transmission of a long space.

 

 

 

 

 

 

 

 

Zn

Reset and Load Active

 

 

Control\Reset

 

Z0

Loads configuration options from Active (Saved) to Active

 

 

 

(Operating).

 

 

 

 

 

Z1

Loads configuration options from Customer 1 to Active (Operating).

 

 

Z2

Loads configuration from Customer 2 to Active (Operating).

 

 

Z3

Loads configuration options from Active (Saved) to Active

 

 

 

(Operating) and performs a reset (if the modem is connected, it is

 

 

 

disconnected).

 

 

 

 

Z9

Performs a full modem reset, as if the power were turned off and

 

 

 

on.

 

 

 

 

 

 

 

 

 

 

 

13-6

November 1996

3980-A2-GB30-20

Page 129
Image 129
Paradyne 3800PLUS 4 of 3800Plus AT Commands, Description, Front Panel Branch, Configuration Options, Dial, Busy, Extended