ASMi-450 Alarm Buffer Messages Cont’d | RAD Data comm ASMI-450

Diagnostics

Table 5-1. ASMi-450 Alarm Buffer Messages (Cont’d)

	Message	Description	Corrective Actions	Alarm
	Message	Description	Corrective Actions	Type
				Type


	LOCAL PSWRD	Section PSWD of switch S1 of the	If it is no longer necessary to enforce	ON
	SWITCH IS ON	local ASMI-450 is set to ON	the default password and node
			number, change setting to OFF
	LOCAL REAL TIME	The battery that powers the local	Have the ASMi-450 repaired	ON
	CLOCK BATTERY	ASMi-450 internal real-time clock
	FAILURE	when ASMi-450 is not powered has
		failed
	LOCAL RECEIVE	A slip has been detected by the local	Check the selection of clock sources	ON
	SLIP	ASMi-450 in the receive path	at the local and remote ASMi-450
			units
	LOCAL REVERSE	Reserved loop polarity has been	The ASMi-450 continues normal	ON
	POLARITY	detected by the local ASMi-450	operation
	LOCAL SELF TEST	A problem has been detected during	Repeat self-test, and replace the	ON
	ERROR	local ASMi-450 self-test	ASMi-450 if it fails the self-test
	LOCAL SIGNAL LOSS	Loss of HDSL line input signal at the	1. Check the HDSL line.	ON/OFF
		local ASMi-450	2. Perform self-test on the two
			ASMi-450 and replace the
			ASMi-450 that fails the self-test
	LOCAL SP-PAR	Section DEF SP of switch S1 of the	If it is no longer necessary to enforce	ON
	SWITCH IS ON	local ASMi-450 is set ON	the default control port parameters,
			change setting to OFF
	LOCAL SYNC LOSS	Loss of synchronization on the	1. Check the HDSL line	ON/OFF
		HDSL line at the local ASMi-450	2. Perform self-test on the two
			ASMi-450, and replace the
			ASMi-450 that fails the self-test
	LOCAL TRANSMIT	A slip has been detected by the local	Check the selection of clock sources	ON
	SLIP	ASMi-450 in the transmit path	at the local and remote ASMi-450
			units
	REM TRANSMIT SLIP	A slip has been detected by the	Check the selection of clock sources	ON
		remote ASMi-450 in the receive path	at the local and remote ASMi-450
			units
	REM RECEIVE SLIP	A slip has been detected by the	Check the selection of clock sources	ON
		remote ASMi-450 in the receive path	at the local and remote ASMi-450
			units

ASMi-450 Installation and Operation Manual

5-3

Image 91

RAD Data comm ASMI-450 operation manual ASMi-450 Alarm Buffer Messages Cont’d

Contents

ASMi-450 Warranty Hdsl Selv Regulatory Information Declaration of Conformity Page Contents ASMi-450 Control from the Control Port Appendix a Connector Wiring Contents List of Figures List of Figures Xii List of Tables List of Tables Xiv Preliminary Preparations Starting Procedure Starting the Configuration Step Action Use the Command Configuration ProcedureFunction Terminal Type TV920 VT52 VT100 Freedom 100/110 Type Configuration Display Commands Control Commands Command Index Quick-Start Guide Functional Description Purpose and Main Features Typical Application for ASMi-450 with Data Interface Hdsl Subsystem Characteristics Internal timing System Timing Local Control Control ASMi-450 OperationRemote Management Introduction Power Requirements Test and Diagnostics CapabilitiesAlarms Physical Characteristics Binary Digits Quaternary Symbol Transmission Media Hdsl Line SignalOperating Environment Hdsl Signal Structure HDSL-Related System Functions Hdsl Interface Technical Specifications Ethernet Interface Physical Characteristics General Chapter Installation Site Requirements Unpacking General ASMi-450 Configuration InformationOpening ASMi-450 Case Switch S1 Jumper and Switch Location Functions ASMi-450 Internal Settings OFF Jumper R/C Internal Settings Procedure Reinstalling ASMi-450 CoverJumper FGND/GND Connector Location Grounding AC Power Connection Power Connection Users Port ConnectionsDC Power Connection Hdsl Line Connections Control Port Connection Scope Chapter Front-Panel Operating Instructions Control or Indicator Function Front Panel Controls, Connectors, and Indicators Indicator Function IndicatorsEthernet Interface General General Operating Instructions Display Functions Control of ASMi-450 Operation, General Display Description See Configuration ParametersStatus Messages Test Functions Push-buttons Using Front-PanelOrganization ASMi-450 Display Front-Panel Operating Instructions Designation Function Values System Configuration Parameters Control Port Configuration Parameters Operating Instructions Turn-on Checking Current Operating Configuration Cursor DisplayScroll Ethernet Interface Indications Fault IndicationsStep Action Key Display Normal Front-Panel Indications Protection Local Configuration Set-Up ProcedurePassword Configuration Procedure Already there Scroll to display the desired group Alarm Buffer Specific Configuration Guidelines SP Parameters LCD Configuration Error Messages Front-Panel Operating Instructions Chapter ASMi-450 Control from the Control Port Hardware Requirements Clear to Send CTS Interface TypeData Terminal Ready DTR Request to Send RTS Ring Indication RI Autobaud FunctionData Set Ready DSR ASMi-450 Preparations Supervision Terminal Connections Internal SettingsControl Port Configuration Preparation for Use of Supervision Terminal Option Meaning Example of Usage Command Language Syntax Command OptionsCommand Protocol ASMi-450 Supervision Language Index of Commands Command Purpose Options Format ASMi-450 Command Set DescriptionCLR ALM CLR Loop Date CLR TSTDEF Agent Display Fields DEF Name DEF PWD DEF Node Purpose Format Use DEF SP PWD DEF Term DEF SYS Function Terminal Type VT-52 VT-100 Freedom-110 DSP ALMFormat Use Alarm No Alarm Syntax Meaning State Time Remote DB Remote AlarmRemote Signal Loss Quality Alarm Connected DSP HDR TSTDSP ST Line REM LAN not Display Format DSP ST PortPurpose Format Use Display Format Exit DSP ST SYS Help Init DB Parameter Designation Default Value Loop PasswordNode Time Reset Starting a Session Single ASMi-450 Control Session Ending a Control Session Configuration Error Messages ASMi-450 Control from the Control Port Status Indications and Messages Indicators Display ON/OFF Message Description Corrective Actions Alarm ASMi-450 Alarm Buffer Messages Cont’d Remote Alarm Remote Reverse Test Functions Test Functions Operating Instructions Loop REM REM Port Activating the Test Functions from a Control Terminal Power-Up Self-Test Trouble Symptoms Probable Cause Corrective Measures Troubleshooting Instructions LAN Pin Designation Direction Function RS-530 DCE Connector and Adapter Cables Rcea Pin Designation Direction Function 36/RS-449/422Rceb V.35 DCE Connector X.21 DCE Connector Pin Line Connected Connected to To Terminal Hdsl Line ConnectorRS-232 V.24 Control Port Connector Pin Function Ethernet Interface Connector Appendix B Snmp Management General Snmp Principles Snmp EnvironmentSnmp Operations MIB Structure Management Information BaseMIBs Supported by the ASMi-450 Snmp Agent Management Domains Under Access Restriction Using Snmp CommunitiesSnmp Communities Read ASMi-450 Communities Address Class First Byte Address Range IP EnvironmentGeneral IP Environment IP Address Structure Snmp Management Snmp Traps Appendix C Installation in 19 Racks Figure C-1. Installation of Single Unit in 19 Rack Installation of Single Unit General Preparations Installation of Two Units Fastening the Two Units ASMi-450 To install the ferrite cores