Siemens ST PCS 7 IM 152-1 interface module, 11/33, TM-IM/IM terminal module for, S7-300 rails

© Siemens AG 2007

Process I/O

ET 200iSP distributed I/O

IM 152-1 interface module

■Overview ■Design

The IM 152 interface module connects the ET 200iSP to the PROFIBUS DP with intrinsically-safe RS 485-iS transmission technology with transmission rates up to 1.5 Mbit/s. A redundant connection is also possible. In this case the ET 200iSP is con- nected via two interface modules to two redundant PROFIBUS DP segments of a fault-tolerant automation system.

The IM 152 is plugged onto a special terminal module (to be or- dered separately). The following terminal modules are available:

•TM-IM/EM60 terminal module for one interface module and one electronics module (with screw-type or spring-loaded ter- minals)

•TM-IM/IM terminal module for two interface modules (for re- dundant PROFIBUS DP connection)

The terminal module of the IM 152 (TM-IM/EM or TM-IM/IM) is connected directly next to the power supply unit on the DIN rail. The PROFIBUS DP connection of the IM 152 is made using the standard Sub-D socket on the terminal module. The matching connection element we provide is a special terminating plug with selectable terminating resistance. The terminating resistance must be activated on the last ET 200iSP station of each PROFIBUS DP segment.

Hot swapping of the IM 152 and the PROFIBUS connector is per- missible under hazardous conditions.

A terminating module is provided together with the IM 152, and must be fitted at the right end of each ET 200iSP station following the last electronics module.

The IM 152 has a slot for micro memory cards (MMC). The firm- ware can therefore be updated either via the PROFIBUS DP or using MMCs.

The PROFIBUS addresses can be set using DIL switches at the front which are protected by a cover.

LEDs on the front of the IM 152 signal the supply voltage, group faults, bus faults, the active IM with redundant operation, and the operating state of the fitted power supply modules.

■Selection and Ordering Data		Order No.
IM 152-1 interface module for		6ES7 152-1AA00-0AB0
ET 200iSP
incl. terminating module
	TM-IM/EM60 terminal module
	for ET 200iSP
	for one IM 152 module and one
	electronics module

Tasks of the IM 152 interface module

•Connection of ET 200iSP to the intrinsically-safe

PROFIBUS DP

•Autonomous communication with the host automation system

•Preparation of data for the fitted electronic modules

•Saving of parameters of the electronics modules

•The IM 152 can assign a 20-ms time stamp to digital process signals.

The maximum address space of the interface module is 244 bytes for inputs, and 244 bytes for outputs.

• TM-IM/EM60S (screw-type	6ES7 193-7AA00-0AA0	B)
terminals)
• TM-IM/EM60S (spring-loaded	6ES7 193-7AA10-0AA0	B)
terminals)
TM-IM/IM terminal module for	6ES7 193-7AB00-0AA0
ET 200iSP
for two IM 152 modules
(redundant operation)			11
Accessories
PROFIBUS connector with	6ES7 972-0DA60-0XA0	B)
selectable terminating resistor
for connection of IM 152 to
PROFIBUS DP with RS 485-iS
transmission technology
RS 485-IS coupler	6ES7 972-0AC80-0XA0
Isolating transformer for connec-
tion of PROFIBUS DP segments
with RS 485 and RS 485-iS trans-
mission technologies
S7-300 rails
• 585 mm long, suitable for	6ES7 390-1AF85-0AA0
assembly of ET 200iSP in a
650-mm wide wall housing
• 885 mm long, suitable for
	6ES7 390-1AJ85-0AA0
assembly of ET 200iSP in a
950-mm wide wall housing

B) Subject to export regulations: AL: N, ECCN: EAR99H

For further accessories such as labeling strips or plates, see Catalog IK PI or the A&D Mall/CA 01 under "ET 200iSP distributed I/O".

Siemens ST PCS 7 · November 2007

11/33