Star Micronics NX-1020 SET/EJECT/PARK button , PITCH button

If you also press the C ON LINE ) button while you are line-feeding, the

paper will feed automatically to the top of the next page. This is explained

later.

If you press this button while on-line, this will alternately flash the QUIET

indicator on and off. When in Quiet mode with the QUIET indicator lit, the

printer will print slightly slower, but at a reduced noise level.

SET/EJECT/PARK button

NOTE: This button has no effect if the bottom feed mode is selected.

Pressing this button causes the printer to begin paper loading if the paper has

not loaded while in the off-line state.

If the paper has been loaded, this button results in different functions de-

pending on the position of the release lever.

If the release lever is forward for fanfold forms, pressing this button parks

the forms.

If the release lever is back for single sheets, pressing this button ejects the

paper.

PITCH button

This button allows you to select the printing pitch. Remember that the printer

must be off-line for you to do this. Successive presses of this button will

illuminate (and select) the following options in order:

Pitch Indicator(s)

Pica (10 CPI) 1OCPl

Elite (12 CPI) 12CPI

Condensed pica (17 CPI) lOCPI, COND

Condensed elite (20 CPI) 12CPI, COND

Proportional PROP

Contents

Main 0 Copyright 1990 Star Micronics Co., Ltd. HOW TO USE THIS MANUAL Page FEATURES OF THE PRINTER Chapter 1 SETTING UP THE PRINTER Chapter 2 CONTROL PANEL OPERATIONS Page Chapter 7 TROUBLESHOOTING AND MAINTENANCE 107 Chapter 8 SPECIFICATIONS Chapter 9 CHARACTER SETS INDEX COMMAND SUMMARY 136 Chapter 1 SETTING UP THE PRINTER LOCATING THE PRINTER Page Identifying printer parts SETTING UP Mounting the platen knob Piaten Install the ribbon cartridge and the roller unit Page Page Page Connecting the printer to your computer \ -i \ % \Y LOADING SINGLE SHEETS Automatic loading Page Manual loading I / Loading the paper from the rear of the printer Page Page Loading the paper from the bottom of the printer Paper parking Paper unparking LOADING MULTI-PART FORMS ADJUSTING THE PRINTING GAP Page Chapter 2 CONTROL PANEL OPERATIONS BUTTONS AND INDICATORS ON LINE button PAPER FEED button SET/EJECT/PARK button PITCH button FONT button POWER-UP FUNCTIONS Short test mode Long test mode ON * * * x * * * Ir I: 1: * t * * I 1: Igun, Print area test mode Stay in Panel Pitch Stay in Panel Font Stay in Panel Pitch and Font Hexadecimal dump Page SWITCH COMBINATION FUNCTIONS Form feed Top of form Forward micro-feed Reverse micro-feed Changing the auto loading value Clearing the buffer/All reset Selecting the print color Store Macro Definition Page Chapter 3 DEFAULT SETTINGS HOW TO SET THE EDS MODE FUNCTIONS OF THE EDS SETTINGS I Page Page Page BIDIRECTIONAL TEST/ADJUSTMENT MODE Chapter 4 PRINTER CONTROL COMMANDS FONT CONTROL COMMANDS Select draft quality characters Select draft elite characters Select NLQ characters Select NLQ font Select Courier characters Select Sanserif characters Select Script characters Select Orator characters Select italic characters Select NLQ italic characters Select upright characters Emphasized printing Cancel emphasized printing Double-s trike printing Cancel double-strike printing Start underlining Stop underlining Start 0 verlining Stop overlining Superscript Subscript Page Select international character set Select IBM code page Enable printing of a// character codes Enable printing of all character codes on next character Select slash zero Select normal zero Page Cancel condensed printing Expanded printing Cancel expanded printing Expanded printing for one line Cancel one-line expanded printing Select proportional spacing Select fixed spacing Select master print mode increase character spacing Select double or quadruple size Select character size Print double-height characters Return to normal height Select character height, width, and line spacing VERTICAL POSITION COMMANDS Set line spacing to I/8 inch Set line spacing to 7/72 inch Set line spacing to I/6 inch Set line spacing to n/216 inch Set line spacing to nD2 inch Execute <ES& A Line feed Reverse line feed Perform one n/216-inch line feed Perform one n/216=inch reverse line feed Feed paper n lines Set top of page at current position Set page length to n lines Set page length to n inches Set bottom margin Cancel bottom margin Form feed Return to top of current page Disable paper-out detector Enable paper-out detector Set vertical tab stops Set vertical tab stops every n lines Set vertical tab stops in channel Select vertical tab channel Vertical tab HORIZONTAL POSITION COMMANDS Set left margin Set right margin Set leff and right margins Carriage return Set automatic line feed Cancel automatic line feed Backspace Left justify Center text Right justify Full justify Set horizontal tab stops Set horizontal tab stops every n columns Reset all tab stops Horizontal tab Relative horizontal tab Absolute horizontal tab in inches - Absolute horizontal tab in columns Print normal-density 8-bit graphics Print double-density 8-bit graphics Print double-density, double-speed 8-bit graphics Print quadruple-density 8-bit graphics Select graphics mode Convert graphics density Print O-pin graphics DOWNLOAD CHARACTER COMMANDS Define draft download characters Define NLQ download characters Define draft download characters Define NLQ download characters Copy character set from ROM into RAM .- Select download character set Shift download character area Select draft download character set Select draft elite download character set Select NLQ download character set Select NLQ italic download character set Select ROM character set COLOR SELECTION COMMANDS select print color Select black Select magenta Select cyan Select violet Sekt yellow Select orange Select green Page Quiet print Cancel quiet print Set printer off-line Set printer on-line Bell Bidirectional printing Unidirectional printing One-line unidirectional printing Manual feed Auto feed Eject paper from ASF Set print start position on ASF Reset printer Page chapter 5 DOWNLOAD CHARACTERS DESIGNING YOUR OWN DRAFT CHARACTERS Defining the attribute data Assigning the character data Sample program Page DEFINING YOUR OWN NLQ CHARACTERS Assigning the character data with the Standard mode Page Page U.S. EXPORTS Assigning the character data with the IBM mode Page Page Page Page chapter 6 MS-DOS AND YOUR PRINTER INSTALLING APPLICATION SOFTWARE WITH YOUR PRINTER EMBEDDING PRINTER COMMANDS PRINTER COMMANDS PROGRAMMING THE PRINTER WITH DOS COMMANDS A>PRINT README.DOC Name of list device A>PRINT/T A>COPY README.DOC PRN A>TYPE README.DOC >PRN ASEDLIN NLQELITE.DAT New file "1. 1: *'-V[Xl"V[!'VA 2:*-c - *E Page PROGRAMMING WITH BASIC Page Page How the program works Expanded I Double-height, Double-sized, Quad-sized. Page chapter 7 TROUBLESHOOTING AND MAINTENANCE TROUBLESHOOTING - Power supply If the POWER indicator does not illuminate, check the following: Printing If your printer does not print, or suddenly stops printing, check the follow- ing: Is the ON LINE indicator illu- If the print is faint, or uneven, check the following: If dots are missing in the printing, check the following: If the printout is not what is expected: -. Paper feeding I -- If the ASF is not operating or is not feeding paper correctly, check the following: w Page MAINTENANCE REPLACING THE PRINT HEAD Page chapter 8 SPECIFICATIONS NLQ Page Page I chapter 9 r CHARACTER SETS L Page Page Page INTERNATIONAL CHARACTER SETS d - h - , Page 0 c 128 1 ii 129 2 Code Page #850 (Mu/i-lingual) I-! I ! lAl%-k--JY-hI I ! Code Page #860 (Pomguese) %!I 1 Other charcters are identical to Code Pane #437. Page Page Page Page Page lA/DEX CKI IBI IGI IHI m CEI ccl (VJ El IQI COMMAND SUMMARY Standard Mode The following commands take effect with the Standard mode. Page :: :; IBM Mode The following commands take effect with the IBM mode. 139 select green