Remote Operation

Model GFC7001E Carbon Dioxide Analyzer

To assign or reset the status flag bit assignments, press:

<TST

TST>

CAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SETUP X.X

 

 

 

 

CFG

DAS

RNGE PASS CLK

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SETUP X.X

 

 

 

 

 

 

VARS DIAG

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SETUP X.X

 

 

 

 

ID

 

 

COM1 COM2

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Continue pressing until ...

The and

keys move the cursor brackets “

left and right along the

bit string.

SETUP X.X

EDIT PRNT EXIT

 

Continue pressing

until desired

 

 

 

 

 

 

flag message is displayed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SETUP X.X

 

 

 

 

 

 

 

 

 

PREV NEXT

 

PRNT EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SETUP X.X

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

discards the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

new setting.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

accepts the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

new setting.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press the

key repeatedly to cycle

 

 

 

 

 

 

 

 

 

 

 

 

 

 

through the available character set:

 

 

 

deletes the

 

: Values of

can also be set

 

 

character currently

 

 

but are meaningless.

 

 

inside the cursor

 

 

 

 

 

 

 

 

 

 

brackets.

 

 

 

 

 

 

 

 

8.6.8.INSTRUMENT ID CODE

Each instrument on a Hessen Protocol network must have a unique ID code. If more than one GFC 7001E/EM Analyzer is on the Hessen network, you will have to change this code for all but one of the GFC 7001E/EM Analyzer’s on the Hessen network (see Section 8.1.6).

The default ID code for the GFC 7001E/EM Analyzers is 300.

Teledyne Analytical Instruments

183

Page 183
Image 183
Teledyne GFC 7001EM operation manual Instrument ID Code, To assign or reset the status flag bit assignments, press