Appearance, Dimensions, Front View | Toshiba CB-416-T3-QQ specification

		Chapter 1	Product Overview
1.5	Appearance	The names of the parts or units introduced in this section are used in
		the following chapters.

1.5.1Dimensions

Note:

Depth is 34.4 inches (875mm) when the Cutter Module is installed on the printer.

13.7(350)

15.1

(385)

20.4(520) 11.0(280)

Dimensions in inches + (mm)

1.5.2	Front View	Top Cover
		Message Display (LCD)
		Supply Roll Holder
		Supply Shaft Holder

Operation Panel	Supply Shaft Holder Stand
	Supply Shaft Holder Stand
	Media Outlet

1.5.3Rear View

	Serial Interface Connector
Media Sensor Adjuster	(RS-232C)

Air Vents

(Cooling Fans)

Expansion I/O

Interface Connector

Media Inlet

Parallel Interface

Connector

(Centronics)

	Supply Shaft Holder Slots	Power Switch
	Supply Shaft Holder Slots	AC Power Inlet
		AC Power Inlet
		Harness

4

Image 12

Toshiba CB-416-T3-QQ owner manual Appearance, Dimensions, Front View, Rear View

Contents

CB-416-T3-QQ For Canada onl y Safety Precautions Safety SummaryMeanings of Symbols Any other than the specified AC voltage is prohibited Iii Request Regarding Maintenance Table Contents of Contents TOC Introduction Features Unpacking Product Overview Accessories and Options Accessories Cool Release Enhancement KitOptions Dimensions AppearanceFront View Rear View Operation Panel Interior Printer Installation Installing the AccessoriesFan Filters Media Slide Connecting the Printer to Your Computer Connecting the Power Cord Turning on/off the Printer Turning on the Printer Turning off Printer Loading the Media Measure width of the media that will be loaded Slide the Supply Roll Holder inside to the loaded media RightWrong Top View of the Printer Side View of the Printer Additional Information Sensor Adjustments Black Mark Sensor Feed Gap Sensor Adjustment Media Sensor AdjustorBlack Mark Sensor Sensitivity Adjustment Media Sensor Open the Top Cover Loading Procedure Loading the Ribbons For Hot ReleaseRibbon Positions Ribbon Width Media Width Procedure Loading Ribbon Module Print Head Block Loading the Ribbons Part Name Quantity Installing the Ribbon Plate Installing the SP Ribbon GuidesThem in the direction of the arrow Installing the Ribbon Tension Sheet Loading the Cold Release Ribbons Installation Procedure For Windows98 PrintingSystem Requirements Preparation Installation Click Next To continue the setup Chapter Printing Installation Procedure Adding the Printer For Windows98 Click Have Disk ∙ The ECPPrinter port is recommended Uninstalling the Printer Driver Chapter Properties Displaying PrinterProperties Summary of Properties This is a summary of the main properties for CB-416-T3 Setup Selecting a label size Creating a new label size User Defined cannot be renamed Orientation ∙ a preview will be shown, as each option is selected User Commands Miscellaneous Tab Settings See Section Transfer Mode Print Density AdjustmentPrinting Preferences Name Click Export. The Save Devices Settings File screen appears To enable the saved settings, use the following procedures Click Import. The Open Device Settings File screen appearsCont Graphics Dithering Intensity ColorColor Registration Click Color Registration on the Graphics property Color 0 Yellow Sample Y5 in Vertical Y on Align Color Yellow/Black Spot Color Setup Spot Color Printing Bar Fonts Specifying a New Font Style Font Style Stock Print MethodSensor Label Gap Issue Settings Fine Adjustment Transfer Mode Print Density AdjustmentOptions Device Settings MaintenanceRibbon Settings Reset Testing Print Test LabelFeed Cut Procedures Click Print Test Label on the Device Settings propertyPrint Test Printing a Label On the File menu, click Print Printing a Label Printing a Label Online Mode Illuminates when Flashes whenOperation Panel Reset OperationOn Line No Paper Maintenance CleaningPrint Head/Platen Turn off the printer. Unplug the power cord Pinch Roller/Feed Roller/Media Guide Covers and Panels Ribbon Modules Troubleshooting Error MessagesError Messages Problems/Causes Solutions Switch to the right Back Tension Possible Problems Possible Problems Causes Solutions From the Pinch Roller Unit From the Print Head Block When the Ribbon is Torn Apart Appendix 1 Specifications A1.1 PrinterModel CB-416-T3-QQ A1.2 Options A1.3 Media Name Model DescriptionA1.3.1 Media Type Label Tag A1.3.2 Detection Area of the Transmissive Sensor Below A1.3.3 Detection Area Reflective SensorA1.3.4 Effective Print Area A1.4 Ribbon Type Spool Type Appendix 2 DIP Switches A2.1 DIP Switch a Function A2.2 DIP Switch B OFF Even A2.3 Ribbon Near End Detection Label Settings Issue Mode SettingsAppendix 3 Quick Reference for Printing Actions Path to Find the Property See Section Other Settings Actions Path to the Property See Section TAB Function See Section Remarks Symbols in the Message Appendix 4 Message and LEDLED Indication LCD Messages Printer Status Message and LED ` YES Appendix 5 System Mode A5.1 Operation Panel A5.2 Overview 2PARAMETER SET 3TEST Print4RAM Clear A5.3 Self-Diagnostic Test Auto DiagnosticMaintenance Sensor None A5.4 Parameter Setting Head Error KMCHead Check Checking A5.4 Parameter Making Positional Adjustments Position Print Density BlackMagenta +0 CYAN+3 Head Adjust Issue CountPrint Condition Print Speed 6/S Adjust Printing the X/Y Direction Alignment Caliper-shaped Pattern Direction Black F00Magenta F00 Cyan F05 Magenta B00 Cyan B05Check Printer Para PM Adjust Code AutoPulse Motor Auto Euro Code Head Select Black onMagenta on Ribbon A5.5 Test Print Specifying the Print Condition for the Test PrintPause key again Types no CUT Quality HighPaper Feed Printing out the Slant Line Pattern Slant Linem ColorCharacters Barcode A5.6 RAM Clear No RAM ClearMainte CNT Clear Complete Clearing the Print Distance Print Step ClearALL Color A5.7.1 Self-Diagnostic Test Result Sample and Descriptions Switch CheckA5.7 Additional Information Memory Check Maintenance Counter Parameters A5.7.5 X-Coordinate Fine Adjustment A5.7.3 Cut Operation ExampleA5.7.4 Pulse Motor Speed A5.7.6 Magnified Views of Slant Line Pattern Initial Value 110 111 Appendix 6 Interface