Adjust | Toshiba CB-416-T3-QQ guide

Appendix 5

System Mode

A5.4 Parameter Setting (Cont.)

Printing the X/Y Direction Alignment (Caliper-shaped Pattern)

HEAD ADJUST

X/Y Direction Alignment Tests X Direction

Press the PAUSE key. “HEAD ADJUST” appears. Then press the PAUSE key again.

ADJUST

Press the PAUSE key. The printer starts printing the X/Y Direction Alignment Tests using the print conditions specified above.

When printing completes, the message returns to “<2>

PARAMETER SET”.

Based on the printed patterns, make the X/Y direction alignment for all colors.

Y Direction

96

Image 104

Toshiba CB-416-T3-QQ owner manual Printing the X/Y Direction Alignment Caliper-shaped Pattern, Adjust

Contents

CB-416-T3-QQ For Canada onl y Meanings of Symbols Safety PrecautionsSafety Summary Any other than the specified AC voltage is prohibited Iii Request Regarding Maintenance Table Contents of Contents TOC Introduction Features Unpacking Product Overview Accessories and Options Accessories Options Cool ReleaseEnhancement Kit Dimensions AppearanceFront View Rear View Operation Panel Interior Printer Installation Installing the AccessoriesFan Filters Media Slide Connecting the Printer to Your Computer Connecting the Power Cord Turning on/off the Printer Turning on the Printer Turning off Printer Loading the Media Measure width of the media that will be loaded Slide the Supply Roll Holder inside to the loaded media RightWrong Top View of the Printer Side View of the Printer Additional Information Sensor Adjustments Black Mark Sensor Feed Gap Sensor Adjustment Media Sensor AdjustorBlack Mark Sensor Sensitivity Adjustment Media Sensor Open the Top Cover Loading Procedure Loading the Ribbons For Hot ReleaseRibbon Positions Ribbon Width Media Width Procedure Loading Ribbon Module Print Head Block Loading the Ribbons Part Name Quantity Installing the Ribbon Plate Them in the direction of the arrow Installing the SPRibbon Guides Installing the Ribbon Tension Sheet Loading the Cold Release Ribbons Installation Procedure For Windows98 PrintingSystem Requirements Preparation Installation Click Next To continue the setup Chapter Printing Installation Procedure Adding the Printer For Windows98 Click Have Disk ∙ The ECPPrinter port is recommended Uninstalling the Printer Driver Chapter Properties PropertiesDisplaying Printer Summary of Properties This is a summary of the main properties for CB-416-T3 Setup Selecting a label size Creating a new label size User Defined cannot be renamed Orientation ∙ a preview will be shown, as each option is selected User Commands Miscellaneous Tab Settings See Section Transfer Mode Print Density AdjustmentPrinting Preferences Name Click Export. The Save Devices Settings File screen appears Cont To enable the saved settings, use the following proceduresClick Import. The Open Device Settings File screen appears Graphics Dithering Intensity ColorColor Registration Click Color Registration on the Graphics property Color 0 Yellow Sample Y5 in Vertical Y on Align Color Yellow/Black Spot Color Setup Spot Color Printing Bar Fonts Specifying a New Font Style Font Style Stock Print MethodSensor Label Gap Issue Settings Fine Adjustment Options Transfer ModePrint Density Adjustment Ribbon Settings Device SettingsMaintenance Reset Testing Print Test LabelFeed Cut Print Test ProceduresClick Print Test Label on the Device Settings property Printing a Label On the File menu, click Print Printing a Label Printing a Label Operation Panel Online ModeIlluminates when Flashes when Reset OperationOn Line No Paper Print Head/Platen MaintenanceCleaning Turn off the printer. Unplug the power cord Pinch Roller/Feed Roller/Media Guide Covers and Panels Ribbon Modules Error Messages Problems/Causes Solutions TroubleshootingError Messages Switch to the right Back Tension Possible Problems Possible Problems Causes Solutions From the Pinch Roller Unit From the Print Head Block When the Ribbon is Torn Apart Model CB-416-T3-QQ Appendix 1 SpecificationsA1.1 Printer A1.2 Options A1.3 Media Name Model DescriptionA1.3.1 Media Type Label Tag A1.3.2 Detection Area of the Transmissive Sensor Below A1.3.4 Effective Print Area A1.3.3 Detection AreaReflective Sensor A1.4 Ribbon Type Spool Type Appendix 2 DIP Switches A2.1 DIP Switch a Function A2.2 DIP Switch B OFF Even A2.3 Ribbon Near End Detection Label Settings Issue Mode SettingsAppendix 3 Quick Reference for Printing Actions Path to Find the Property See Section Other Settings Actions Path to the Property See Section TAB Function See Section Remarks Symbols in the Message Appendix 4 Message and LEDLED Indication LCD Messages Printer Status Message and LED ` YES Appendix 5 System Mode A5.1 Operation Panel A5.2 Overview 4RAM Clear 2PARAMETER SET3TEST Print A5.3 Self-Diagnostic Test Auto DiagnosticMaintenance Sensor None A5.4 Parameter Setting Head Error KMCHead Check Checking A5.4 Parameter Making Positional Adjustments Position Print Density BlackMagenta +0 CYAN+3 Head Adjust Issue CountPrint Condition Print Speed 6/S Adjust Printing the X/Y Direction Alignment Caliper-shaped Pattern Direction Black F00Magenta F00 Cyan F05 Magenta B00 Cyan B05Check Printer Para PM Adjust Code AutoPulse Motor Auto Euro Code Head Select Black onMagenta on Ribbon Pause key again A5.5 Test PrintSpecifying the Print Condition for the Test Print Types no CUT Quality HighPaper Feed Printing out the Slant Line Pattern Slant Linem ColorCharacters Barcode A5.6 RAM Clear No RAM ClearMainte CNT Clear Complete ALL Color Clearing the Print DistancePrint Step Clear A5.7.1 Self-Diagnostic Test Result Sample and Descriptions Switch CheckA5.7 Additional Information Memory Check Maintenance Counter Parameters A5.7.5 X-Coordinate Fine Adjustment A5.7.3 Cut Operation ExampleA5.7.4 Pulse Motor Speed A5.7.6 Magnified Views of Slant Line Pattern Initial Value 110 111 Appendix 6 Interface