Xerox 16 Series 3, 4

Starting a Job 2-21

3Click on the On-line Finishers tab. The window will display as shown

below.

Figure 2-19: On-line Finishers tab

4Verify that the profile for the Downstream device to be used is

Enabled.

lFor punching and stacking the 11" edge in the Xerox High Capacity

Stacker, ensure the HCS profile is Enabled.

lFor punching and stacking the 8.5" edge, ensure the GBCSE

profile is Enabled.

lFor all other applications, ensure the profile that associates with the

Downstream device to be run is Enabled.

(In the figure above is an example of a job being sent to a Signature

Booklet Maker.) If this profile is not visible in this window,

go to step 8. If this profile is visible but not Enabled (green check-mark

in the Enabled column), highlight the profile and click Enable and then

click Close.

On-line

Finishers

Tab

Contents

Main Page Page Page Page Page Table of Contents Preface Chapter 1: Getting Started Chapter 2: General Procedures Page FusionPunch II User Guide Preface v Preface WAARSCHUWING WARNING ATTENTION SAFETY MESSAGES IMPORTANT SAFEGUARDS SERVICE Page Chapter 1 Getting Started Page About the FusionPunch II Punch any hole pattern Online At the speed of your printer Page Specifications Control Functions and Locations The Control Panel 1 2 3 Page 4 5 6 7 8 Creating 61XX Profiles and Print Queues Page Page 61XX Profile Setup 1 Page Page Page Page Page Page Page Page 14 61XX Print Queue Setup 1 2 3 4 GBC Punch Queue Output GBC Short Edge Punch Queue Output SBM1/SBM2 Queue Output Page Chapter 2 General Procedures Page Changing Die Sets Page Page Removing and Replacing Die Pins 1 2 Centering the Punch Page Setting the Side Guide 5 6 7 Page Setting the Backgauge 1 2 Page Starting a Job Punching and Stacking 1 2 3 4 Page 7 8 9 Page Starting a Job Bypassing to a Downstream device 1 2 3 4 Page Page 9 Page Using the GBC Stacker 1 2 3 4 5 Page Page Page Clearing Jams Page From the Printer Page From the FusionPunch II Page Page Page Page Page From downstream devices Page Page Page Cleaning the FusionPunch II When to Clean Page Cleaning the Punch 1 2 3 4 5 6 7 Page Page Page Page Page 61XX Personality Profiles Contents Page Page Personality Profiles A-5 GBC FusionPunch II Personality Profiles A-6 Appendix A Device Profile-Properties and Default Limits- Personality Profiles A-7 A-8 Appendix A With C.P. Bourg products downstream Personality Profiles A-9 DocuTech 61XX to FusionPunch II to C.P. Bourg Products Device Profile - Properties and D efault Limits Tab A-10 Appendix A Device Profile - P roperties and Default Limits Tab Personality Profiles A-11 Device Profile - Properties and Default Limits A-12 Appendix A Personality Profiles A-13 A-14 Appendix A Personality Profiles A-15 DocuTech 61X X to FusionPunch II to C.P. Bourg Products Finisher Profile - Properties a nd Limits A-16 Appendix A DocuTech 61XX to FusionPunch II to C.P. Bourg Products Finisher Profile - Properties and Limits Personality Profiles A-17 With the Xerox SBM2 downstream A-18 Appendix A DocuTech 6 1XX to FusionPunch II to SB M2 withou t CIM Device Profile - Properties and Default Limits Tab Personality Profiles A-19 DocuTech 6155/6180 to FusionPunch II to SBM2 without CIM Device Profile - Prop erties and Default Limits Timings Tab A-20 Appendix A DocuTech 6155/6180 to FusionPunch II to SBM2 without CIM Device Profile - Properties and Default Limits Timings Tab Personality Profiles A-21 A-22 Appendix A Personality Profiles A-23 with CIM A-24 Appendix A DocuTech 61 XX to FusionPunch II to SBM 2 - with CIM Personality Profiles A-25 DocuTech 61 XX to FusionPunch II to SBM2 with CIM Finisher Profile - P roperties and Limits DocuTech 135 Host Machine Enablement Xerox 4xxx LPS Host Machine Enablement Xerox 4xxx NPS Host Machine Enablement Xerox 4xxx Output Profile Page Page Page Glossary of Common FusionPunch II Terms