Sigma SQC-122c manual Chapter Options Introduction, Option Card, Full Rack Extender Installation

Page 57

Chapter 4

Options

4.0Introduction

This section covers the installation of optional accessories.

4.1Option Card

No option cards are available for the SQC-122c, although the rear panel has locations for an expansion card. To expand the SQC-122c, the unit can be upgraded to an SQC-222. Contact Sigma for information on this factory-only upgrade.

4.2Full Rack Extender Installation

The Full Rack Extender option (PN 900-007) mounts a single SQC-122c into a full width 19” rack space.

Follow the steps below to assemble the extender and mount the SQC-122c:

Remove SQC-122c

Determine on which side of the SQC-122c you want to attach

Mounting Ear

the rack extender. If a rack mount ear is attached to the

 

SQC-122c on that side, remove the two 10-32 flat head

 

screws that mount the ear, then remove the rack mount ear.

Assemble the

Assemble the extender “box” using the eight 6-32 flat head

Extender

screws, two end panels, and two main panels. Thread two

 

socket head captive panel screws from the inside of one side

 

of the extender. Continue to thread the captive screws until

 

their threads are completely exposed on one side.

Attach the Extender

Place the extender next to the SQC-122c, and thread the

 

captive screws into the SQC-122c threaded holes that were

 

previously used to mount the rack ear. Tighten the captive

 

screws to secure the extender to the SQC-122c.

Attach the Mounting

Attach the mounting ear previously removed from the SQC-

Ears

122c to the extender using the same10-32 flat head screws. If

 

rack mount ears were not already attached to the SQC-122c,

 

attach the other mounting ear also.

Mount the

Slide the entire assembly into an empty 5 ¼” high 19” rack

SQC-122c

mount space. Secure the assembly with four 10-32 rack

 

screws (not supplied).

4-1

Image 57
Contents SQC-122c Thin Film Deposition Controller User’s Guide Safety Symbols Safety InformationWarranty Information Limitation of WarrantyReturn Policy Chapter Operation Table of Contents Chapter Quick StartChapter Menus Chapter OptionsAppendix Thin Film Process Overview Chapter Quick Start IntroductionChapter Quick Start Front Panel Chapter Quick Start Rear Panel Power Input FuseChapter Quick Start System Connections Chapter Quick Start Installation Power Chapter Quick Start Process SetupQuick Setup SelectEdit Mode Layer Chapter Quick StartExit to Main Chapter Quick Start Depositing a Film This page left blank for your notes Chapter Operation Introduction DefinitionsDefining a Film POWER% POWER% Deposition Controls Menu Layer Edit Menu Chapter Operation Defining a ProcessChapter Operation Chapter Operation Sensor Setup Tooling U n d e r 1 0 0 % Chapter Operation Chapter Operation Source Setup Chapter Operation Running a Process Chapter Operation Next Menu Zero THICKNESSkA RATEA/s 824 55.3 Chapter Operation Loop Tuning Chapter Operation No Readings, or Erratic Readings from Sensors Chapter Operation TroubleshootingPoor Rate Stability Incorrect Rate or Thickness MeasurementThis page left blank for your notes Chapter Menus Introduction Chapter Menus Main Menu Default, power-up Main Screen display is shown belowNext SetupMenu Quick FilmChapter Menus Next Menu Screens Exit to Main Edit Chapter Menus Quick Setup MenuPrev Layer Next LayerChapter Menus Main Screen Prev Menu Select Edit Delete Control Knob Chapter Menus Process MenusInsert Layer Control Knob Main Screen Prev Menu Edit Cut PasteExit to Main Prev Menu Edit Control Knob POWER%Chapter Menus Main Screen Prev Menu Edit Delete Control Knob Chapter Menus Film MenusExit to Main Prev Menu Edit Exit to Main Prev Menu Edit THICKNESSkA RATEA/s Deposition Controls Menu Chapter Menus Chapter Menus Chapter Menus Chapter Menus System Parameters Menu Chapter Menus Chapter Menus Mapping Menu Chapter Menus I/O SetupInputs Explanation high input causes Relays Explanation closes whenThis page left blank for your notes Full Rack Extender Installation Chapter Options IntroductionOption Card Appendix Material Parameters General Specifications Appendix SpecificationsMeasurement SourceDisplay Connector Wiring Relay Pins Input PinsAppendix O Connections Appendix Appendix Handheld Remote Controller Appendix EC Declaration of Conformity Complies with the Essential Health and Safety RequirementsDeclares that the product Uses the following standards