Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems pmn manual 5.14.1 Conﬁguring an FE-100FX or FE-100F3 in Port 1 or

Models: pmn

1 150

Download 150 pages 2.96 Kb

Page 94

Advertised Ability (Selectable)

Chapter 5: Local Management

NOTE

In normal operation, the port with an FE-100TX installed automatically establishes a link with the device at the other end of the segment without requiring user setup. However, Local Management provides the user with the option of manually conﬁguring that port.

If an FE-100TX is installed, the ﬁeld steps to Auto-Negotiation, 10Base-T, 10Base-TFD (full duplex), 100Base-TX, and 100Base-TXFD (full duplex). In normal operation, the port with an FE-100TX installed is capable of auto-negotiating the operational mode and no further user setup is required. Section 5.14.3 describes how to manually conﬁgure an FE-100TX.

In Auto-Negotiation, the FE-100TX negotiates to the highest common denominator of the two interfaces. The order of priority of negotiation is 100BASE-TXFD, 100BASE-TX, 10BASE-TFD, and 10BASE-T.

Advertised Ability (Selectable)

During auto-negotiation, the FE-100TX “tells” the device at the other end of the segment about its capabilities. The capabilities of a port (1 or 2) with an FE-100TX installed are 10BASE-T, 10BASE-TFD (full duplex mode), 100BASE-TX and 100BASE-TXFD(full duplex mode). In normal operation, with all capabilities enabled, the FE-100TX “advertises” that it has the ability to operate in any mode. The Network Manager may choose to set up the port so that only a portion of the available capabilities are advertised and the others are disabled. For example, only 100BASE-TX and 100BASE-TXFD might be enabled so that only devices that operate at 100 Mbps can communicate with that port. Section 5.14.5 describes how to enable or disable advertised modes.

5.14.1Conﬁguring an FE-100FX or FE-100F3 in Port 1 or 2

When an FE-100FX or FE-100F3 is installed in port 1 or 2, it must be manually set to operate in the same technology as the device at the other end of the connected segment. Section 5.14.2 provides instructions for manually conﬁguring the port with an FE-100FX or FE-100F3 interface.

5-46	2M46-04R/2M46-04RDC User’s Guide

Image 94

Cabletron Systems pmn manual 5.14.1 Conﬁguring an FE-100FX or FE-100F3 in Port 1 or, Advertised Ability Selectable

Contents

9032363-02 2M46-04R/2M46-04RDC SmartSwitch User’s Guide2M46-04R RESETCOM H S I MPage FCC NOTICE Only qualiﬁed personnel should perform installation procedures2M46-04R/2M46-04RDC User’s Guide CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT INDUSTRY CANADA NOTICEVCCI NOTICE 2M46-04R/2M46-04RDC User’s GuideUNITED STATES GOVERNMENT RESTRICTED RIGHTS EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITYCABLETRON SOFTWARE PROGRAM LICENSE 2M46-04R/2M46-04RDC User’s GuideLASER RADIATION AND CONNECTORS SAFETY INFORMATION CLASS 1 LASER TRANSCEIVERSSAFETY INFORMATION CLASS 1 LASER TRANSCEIVERS 2M46-04R/2M46-04RDC User’s GuideApplication of Council Directives 89/336/EEC 73/23/EEC DECLARATION OF CONFORMITY2M46-04R/2M46-04RDC User’s Guide Manufacturer’s Name Cabletron Systems, Inc2M46-04R/2M46-04RDC User’s Guide CHAPTER CONTENTSINSTALLATION INTRODUCTIONCHAPTER CONTENTSTROUBLESHOOTING CHAPTERAPPENDIX A CONTENTSSPECIFICATIONS 2M46-04R/2M46-04RDC User’s GuideOPTIONAL INSTALLATIONS AND CONTENTSSPECIFICATIONS MODE SWITCH BANK SETTINGSCHAPTER INTRODUCTION 1.1 USING THIS GUIDE1.2 STRUCTURE OF THIS GUIDE 1.3 2M46-04R OVERVIEW 2M46-04R1.3.2 Full Duplex Switched Ethernet 1.3.1 Connectivity1.3.3 Auto-Negotiation 1.3.4 SmartTrunk1.3.5 Runtime IP Address Discovery 1.3.6 Management1.3.8 Standards Compatibility 1.3.7 Switching1.3.10 LANVIEW Diagnostic LEDs 1.3.9 Year 2000 Compliance1.3.11 Optional Features Table 1-1 Fast Ethernet Interface ModulesChapter 1 Introduction 1.4 DOCUMENT CONVENTIONSThe following conventions are used throughout this document 2M46-04R/2M46-04RDC User’s Guide1.5 GETTING HELP 2M46-04R using SNMP network management systems 1.6 RELATED MANUALSThe following manuals may help to set up, control, and manage the Cabletron Systems Cabling Guide2.1 SmartTrunk CHAPTER NETWORK REQUIREMENTS2.2 100BASE-TX NETWORK 2.3 100BASE-FX FIBER OPTIC NETWORK CHAPTER INSTALLATION 3.1 UNPACKING THE 2M46-04R3.3.1 Tabletop or Shelf Installation 3.2 INSTALLING OPTIONS3.3 INSTALLING THE 2M46-04R Install any optional equipment before proceeding to SectionA = 15 cm 6 in B = 57 cm 22.5 in C = 53 cm 21 in D = 213 cm 7 ft Guidelines for the Rackmount Installation 3.3.2 2M46-04R and 2M46-04RDC Rackmount InstallationAttaching the Strain-Relief Bracket Proceed as follows to install the 2M46-04R into a 19-inch rack Figure 3-4 Installing the 2M46-04R in a Rack Figure 3-3 Installing the Rackmount BracketsBonding the Rackmount Brackets to the 2M46-04RDC Rackmount Brackets Figure 3-5 Installing the 2M46-04RDC Rackmount BracketsFigure 3-6 Installing the 2M46-04RDC in a Rack Remove Paint Screws3.4 CONNECTING POWER 3.4.1 Connecting Power to the 2M46-04R3.4.2 Connecting Power to the 2M46-04RDC 48 or 60 Vdc Power Source 3.5 CONNECTING TO THE NETWORK 3.5.1 Connecting a UTP Segment to the FE-100TXA schematic of a crossover cable is shown in Figure 3.5.2 Connecting a Fiber Optic Segment to the FE-100FX and FE-100F3 Figure 3-11 FE-100FX and FE-100F3 Ports RX LED3.6 COMPLETING THE INSTALLATION 3-16 Chapter 3 Installation2M46-04R/2M46-04RDC User’s Guide CHAPTER TROUBLESHOOTING 4.1 USING LANVIEWFlashing indicates an irregular LED pulse Chapter 4 Troubleshooting2M46-04R/2M46-04RDC User’s Guide 2M46-04R/2M46-04RDC User’s Guide Using LANVIEWTable 4-1 LANVIEW LEDs Continued 100 LED 4.2 FE-100TX LEDReceive RX LED No link exists if the associated port 1 or 2 RX Receive LED is off Table 4-3 10/100 LED Indications When RX LED Is OffFE-100TX LED 2M46-04R/2M46-04RDC User’s GuideTable 4-4 Troubleshooting Checklist 4.3 TROUBLESHOOTING CHECKLISTChapter 4 Troubleshooting 2M46-04R/2M46-04RDC User’s Guide4.4 USING THE RESET BUTTON 2M46-04R RESET COMChapter 4 Troubleshooting 2M46-04R/2M46-04RDC User’s GuideCHAPTER LOCAL MANAGEMENT 5.1 OVERVIEW2M46-04R/2M46-04RDC User’s Guide 5.2 LOCAL MANAGEMENT KEYBOARD CONVENTIONSChapter 5 Local Management Table 5-1 Keyboard Conventions5.3 MANAGEMENT TERMINAL SETUP 5.3.1 Console Cable ConnectionFigure 5-1 Management Terminal Connection Chapter 5 Local Management2M46-04R/2M46-04RDC User’s Guide 2M46-04RTable 5-2 VT Terminal Setup 5.3.2 Management Terminal Setup ParametersManagement Terminal Setup 2M46-04R/2M46-04RDC User’s Guide5.3.4 Connecting an Uninterruptible Power Supply 5.3.3 Telnet Connections2M46-04R/2M46-04RDC User’s Guide Management Terminal SetupFigure 5-2 Uninterruptible Power Supply UPS Connection DB9 Port RJ45 COM Port5.4 ACCESSING LOCAL MANAGEMENT 5.4.1 Navigating Local Management Screens Chapter 5 Local Management Figure 5-4 802.1D Switching Mode, LM Screen HierarchyFigure 5-5 802.1Q Switching Mode, LM Screen Hierarchy 5-105.4.2 Selecting Local Management Menu Screen Items 5.4.3 Exiting Local Management Screens5.5 DEVICE MENU SCREEN DEVICE STATISTICS DEVICE CONFIGURATIONNETWORK TOOLS 5.6 DEVICE CONFIGURATION MENU SCREEN Figure 5-8 Device Conﬁguration Menu ScreenSMARTTRUNK CONFIGURATION GENERAL CONFIGURATIONSWITCH CONFIGURATION DEVICE SPECIFIC CONFIGURATION5.7 GENERAL CONFIGURATION SCREEN TFTP Gateway IP Addr Modiﬁable Default Gateway ModiﬁableSubnet Mask Modiﬁable Device Date ModiﬁableDisplays the total time that the device has been operating 5.7.1 Setting the IP Address 5.7.2 Setting the Subnet Mask 5.7.3 Setting the Default Gateway 5.7.4 Setting the TFTP Gateway IP Address5.7.5 Setting the Device Date 5.7.6 Setting the Device Time 5.7.7 Entering a New Screen Refresh Time5.7.9 Setting the Operational Mode 5.7.8 Setting the Screen Lockout Time802.1D SWITCHING, 802.1Q SWITCHING or SECURE FAST VLAN 5.7.10 Conﬁguring the COM Port 5.7.10.1 Changing the COM Port Application 3. Press ENTER to accept the application 5.7.11 Clearing NVRAM 5.7.12 Enabling/Disabling IP Fragmentation 5.8 SNMP COMMUNITY NAMES SCREENThe following explains each SNMP Community Names screen ﬁeld 5.8.1 Establishing Community Names 5.9 SNMP TRAPS SCREEN 5.9.1 Conﬁguring the Trap Table 5.10 SWITCH CONFIGURATION SCREEN Figure 5-15 Switch Conﬁguration ScreenThe following describes each ﬁeld of the Switch Conﬁguration screen 5.10.2 Setting the Age Time Field 5.10.1 Setting the STAStatus Toggle 5.10.3 Setting Enabling or Disabling the Port Status 5.11 DEVICE SPECIFIC CONFIGURATION MENU SCREENFLASH DOWNLOAD HIGH SPEED INTERFACE CONFIGURATIONSYSTEM RESOURCES Figure 5-16 Device Speciﬁc Conﬁguration Menu ScreenPORT REDIRECT FUNCTION 5.12 SYSTEM RESOURCES SCREEN802.1Q VLAN CONFIGURATION BROADCAST SUPPRESSIONThe following brieﬂy explains each ﬁeld of the System Resources screen 5.12.1 Setting the Reset Peak Switch Utilization Chapter 5 Local Management 5.13 HIGH SPEED INTERFACE CONFIGURATION MENU SCREENTo access the High Speed Interface Conﬁguration Menu screen 5-42FAST ETHERNET INTERFACES HSIMS5.14 HIGH SPEED INTERFACE CONFIGURATION SCREEN Figure 5-19 High Speed Interface Conﬁguration ScreenCurrent Oper. Mode Read-only Port Type Read-onlyLink Status Read-only Desired Oper. Mode Selectable5.14.1 Conﬁguring an FE-100FX or FE-100F3 in Port 1 or Advertised Ability Selectable5.14.4 Setting the FE-100TX Desired Operational Mode 5.14.2 Setting the FE-100FX or FE-100F3 Desired Operational Mode5.14.3 Conﬁguring an FE-100TX in Port 1 or 5.14.5 Setting the FE-100TX Advertised Ability 5.15 FLASH DOWNLOAD SCREENThe following brieﬂy explains each ﬁeld of the Flash Download screen 5.15.1 Image File Download Using BootP 5.15.2 Image File Download Using TFTP 5.15.3 Image File Download Using Runtime 5.16 PORT REDIRECT FUNCTION SCREEN Port Redirect function is not supported in 802.1Q mode5.16.1 Displaying the Source and Destination Entries 5.16.2 Changing Source and Destination Ports 5.17 BROADCAST SUPPRESSION SCREEN Figure 5-22 Broadcast Suppression ScreenReset Peak Toggle 5.17.1 Setting the ThresholdTime Since Peak Read-Only 5.17.2 Setting the Reset Peak Rate 5.18 DEVICE STATISTICS MENU SCREENThe Device Statistics Menu screen displays the following items Chapter 5 Local Management 5.19 SWITCH STATISTICS SCREENFigure 5-24 Switch Statistics Screen Port # Read-Only5.19.1 Using the Clear Counters Command 5-62 5.20 INTERFACE STATISTICS SCREENChapter 5 Local Management 2M46-04R/2M46-04RDC User’s GuideName Read-only InErrors Read-onlyInterface Read-only InOctets Read-onlyOutOctets Read-only OutErrors Read-onlyAdmin Status Read-only OutUnicast Read-only5.20.1 Displaying Interface Statistics 5.20.2 Using the Clear Counters Command 5.21 RMON STATISTICS SCREENOwner Read-only RMON Index Read-onlyData Source Read-only Status Read-onlyUndersized Pkts Read-only CRC Align Errors Read-onlyMulticast Pkts Read-only Oversized Pkts Read-only65 - 127 Octets Read-only Total Octets Read-only64 Octets Read-only 128 - 255 Octets Read-only5.22 NETWORK TOOLS 5.21.2 Using the Clear Counters Command5.21.1 Displaying RMON Statistics Type help at the prompt to list all the commands that areThere are two categories of commands in the command set Description 5.22.1 Built-in CommandsSyntax OptionsOptions 1 - Other 2 - Invalid entry cannot ping device, timed out, etcExample Options SyntaxDescription ExampleOptions SyntaxDescription Exampleshow protocol table SyntaxresetNot Applicable OptionsSyntax not reached, the command displays all next-hopExample DescriptionExample OptionsNot Applicable SyntaxDescription ExampleSyntax OptionsDescription 5.22.2 Special CommandsSyntax OptionsA.3 ELECTRICAL SPECIFICATIONS APPENDIX A SPECIFICATIONSA.1 DEVICE SPECIFICATIONS A.2 PHYSICAL PROPERTIESA.4 ENVIRONMENTAL REQUIREMENTS A.5 INPUT/OUTPUT PORTSA.6 COM PORT/PIN ASSIGNMENTS A.7 REGULATORY COMPLIANCEAppendix A Speciﬁcations 2M46-04R/2M46-04RDC User’s GuideAPPENDIX B FE-100TX, FE-100FX, AND FE-100F3 SPECIFICATIONS B.1 FE-100TXAppendix B FE-100TX, FE-100FX, and FE-100F3 Speciﬁcations B.2 FE-100FX2M46-04R/2M46-04RDC User’s Guide 2M46-04R/2M46-04RDC User’s Guide B.3 FE-100F3FE-100F3 FE-100F3Appendix B FE-100TX, FE-100FX, and FE-100F3 Speciﬁcations 2M46-04R/2M46-04RDC User’s GuideAPPENDIX C OPTIONAL INSTALLATIONS AND MODE SWITCH BANK SETTINGS C.1 REQUIRED TOOLSC.2 REMOVING THE CHASSIS COVER 2M46-04R/2M46-04RDC User’s Guide C.2.1 Setting the Mode SwitchRemoving the Chassis Cover Figure C-1 Removing the Chassis CoverSwitch deﬁnitions and positions are as follows Switch 7 - Clear NVRAM. Changing the position of this switch resets NVRAM on either the next power-up or the next operation of the front panel RESET button. All user-entered parameters, such as the IP address, device names, etc., are reset to the factory default settings. Once the 2M46-04R resets, you can either use the factory default settings or reenter your own parameters Figure C-3 Fast Ethernet Interface Module Connector Location C.3 INSTALLING OPTIONAL FAST ETHERNET INTERFACE MODULESAppendix C Optional Installations and Mode Switch Bank Settings 2M46-04R/2M46-04RDC User’s Guideb. Lift and remove the coverplate from the top of the front standoffs 2. Remove the screw from the rear standoff. Save the screw 7. Reinstall the cover C-10 Appendix C Optional Installations and Mode Switch Bank Settings2M46-04R/2M46-04RDC User’s Guide 2M46-04R/2M46-04RDC User’s Guide INDEXNumerics Index-1Index-2 Index2M46-04R/2M46-04RDC User’s Guide 2M46-04R/2M46-04RDC User’s Guide IndexIndex-3 Index-4 Index2M46-04R/2M46-04RDC User’s Guide