Appendix A Cisco 3825 Mobile Wireless Edge Router RAN-O Command Reference

show mpls l2transport vc

Table A-5 show mpls l2transport vc Field Descriptions (continued)

 

 

Field

Description

 

 

 

 

 

 

 

Tunnel label

An IGP label used to route the packet over the MPLS backbone to the

 

 

 

destination router with the egress interface. The first part of the output displays

 

 

 

the type of label. The second part of output displays the route information.

 

 

 

The tunnel label information can display any of the following states:

 

 

 

imp-null—The provider (P) router is absent and the tunnel label is not to be

 

 

 

 

used. Alternatively, imp-null can signify traffic engineering tunnels

 

 

 

 

between the PE routers.

 

 

 

unassigned—The label has not been assigned.

 

 

 

no route—The label is not in the routing table.

 

 

 

no adjacency—The adjacency for the next hop is missing.

 

 

 

not ready, no route—An IP route for the peer does not exist in the routing

 

 

 

 

table.

 

 

 

not ready, not a host table—The route in the routing table for the remote

 

 

 

 

peer router is not a host route.

 

 

 

not ready, Cisco Express Forwarding disabled—Cisco Express Forwarding

 

 

 

 

is disabled.

 

 

 

not ready, LFIB disabled—The MPLS switching subsystem is disabled.

 

 

 

not ready, label forwarding information base (LFIB) entry present—The

 

 

 

 

tunnel label exists in the LFIB, but the VC is down.

 

 

 

 

 

 

 

SSO Descriptor

Identifies the VC for which the information was checkpointed.

 

 

 

 

 

 

 

local label

The value of the local label that was checkpointed (that is, sent on the active

 

 

 

Route Processor [RP], and received on the standby RP).

 

 

 

 

 

 

 

SSM

The IDs used to refer to the control plane and data plane contexts for this VC.

 

 

segment/switch IDs

This data is not for customer use but for Cisco personnel for troubleshooting

 

 

 

purposes. When the source specific multicast (SSM) IDs are followed by the

 

 

 

word "used," the checkpointed data has been successfully sent and not released.

 

 

 

 

 

 

 

PWID

The PW ID used in the data plane to correlate the switching context for the

 

 

 

segment mentioned with the MPLS switching context. This data is not for

 

 

 

customer use but for Cisco personnel for troubleshooting purposes.

 

 

 

 

 

 

 

packet totals

Number of packets sent and received. Received packets are those AToM packets

 

 

 

received from the MPLS core. Sent packets are those AToM packets sent to the

 

 

 

MPLS core. This does not include dropped packets.

 

 

 

 

 

 

 

byte totals

Number of bytes sent and received from the core-facing interface, including the

 

 

 

payload, control word if present, and AToM VC label.

 

 

 

 

 

 

 

packet drops

Number of dropped packets.

 

 

 

 

 

 

 

 

 

 

 

 

Related Commands

 

Command

 

Description

 

 

 

 

 

 

 

 

show mpls l2transport

Displays summary information about VCs that have been enabled to

 

 

summary

 

route AToM Layer 2 packets on a router.

 

 

 

 

 

 

 

 

Cisco 3825 Mobile Wireless Edge Router Software Configuration Guide

 

 

 

 

 

 

 

OL-15667-03

 

 

A-99

 

 

 

 

 

Page 231
Image 231
Cisco Systems 3825 manual Show mpls l2transport, Summary, Route AToM Layer 2 packets on a router