To Obtain a Unit’s Statistics | Honeywell K14392V1 specs

Enhancing Video for Security

To Obtain a Unit’s Statistics

1.Continue or start a Maintenance Session for the Rapid Eye site. Please wait until a “System Operational” message appears in the Feedback box.

2.Click the Statistics tab. There may be a delay, based on the type of connection to the site, until the Feedback box displays “Statistics received”.

3.To update the statistics, click Refresh.

Table 7–8 Storage Statistics for a Multi-Media Unit

Label	Meaning	Unit

Storage Capacity	The total disk space, on unit.	gigabyte (GB)
Daily Usage Rate	The portion of storage used in the last	percentage of storage
	twenty-four hours. For new units, or after	capacity
	clearing storage, the report of Daily Usage
	Rate can be accurate within minutes. In
	regular use, it is averaged over the latest
	7 days of activity.
Estimated Capacity	The amount of storage, based on past	day
	performance. The number may differ from
	the estimate obtained using the Rapid Eye
	Storage Estimator, due to fluctuations in the
	video signal. The estimated capacity
	diminishes if the Continuous video
	recording settings (resolution, quality, ips)
	are set to higher values and as more
	cameras are added.
Time Elapsed*	The time that has passed since the latest	day, hour, minute, second
	change to configuration or latest reboot of
	the Multi-Media unit. Can also be used to
	estimate the oldest available image*.
Percent Full	The portion of storage in use; at “100 %",	percentage of storage
	recycling occurs.	capacity
Stream	device connected to a Multi-Media unit (a	text
	camera, microphone, and so on)
Start Time	time of earliest data	UTC (universal coordinated
		time)
End Time	time of latest data	UTC
Recorded	portion of storage used by a device	percentage of data
Stream ID	n/a; for Multi technical support	integer

*Most helpful on a unit that records continuously. If a unit is off or stops recording for a while, introducing gaps in the video archive, time elapsed still reports only the oldest available video.

Other statistics about the video archive

The Recording tab shows an "Estimated Storage Capacity" in days. See Estimating Storage Capacity, p. 71.

128

Image 128

Honeywell K14392V1 manual To Obtain a Unit’s Statistics, Storage Statistics for a Multi-Media Unit Label Meaning

Contents

Rapid Eye Software Page Revisions Issue Date Page Table of Contents Unit Configuration Basics Pan, Tilt, and Zoom PTZ Setup System Administrator’s Guide Enhancing Video for Security 103 129 Security for a Multi-Media System 161 201 Touring Many Sites 221 Figures Page System Administrator’s Guide Admin Icon on the Windows Desktop 232 Tables System Administrator’s Guide Table of Contents Start Here Administration of a Rapid Eye SystemAbout Using a PC to Operate Rapid Eye Units For the Multi SA Only Admin and View Software Using a PC Installing Rapid Eye SoftwareAbout Using LocalView Onsite Customizing a Unit View Software First Use Running Admin SoftwareUsing View software for site maintenance Calling Honeywell In-depth reference Configuration malfunctionsFor Questions Last valid password Multi-Media Site NamePreparations Road map Four items Site Setup ChecklistNaming / Renaming a Site Click Save and Close Site Naming TipsAfter Dealing with a Site Grouping Sites To Create a FolderTo Assign a Site to a Folder Flexibility To Rename a Folder To Delete a FolderGrouping Folders To assign a folder to a folder Mistakenly Deleting a Secured Site Definition Removing a SiteTo Delete a Site Naming and viewing a connection Multi-Media Site Connection ConfigurationTypes of Connection Dial-up Connection to a Unit Selecting a Network or Dial-up Connection Setting a Dial-Up Connection Automatic Tag Added to a Connections Name Click Use Dial-up Networking as needed To Force a Long-distance Dial-up Using a Local Area CodeArea Code Irregular Use Should you plan to add an alarm station Forcing a Local Dial-up Across Area CodesDial-up Technical Note Click Use Dial-up Networking Using Network Access Offering Many Dial-Up Connections to the Same Unit To Set a Network Connection Site Tab’s Report of Primary Connections Static network settings, default for Multi-Media unit IP defaults used by Multi-Media units Point AddressStandalone Unit and a PC that Has a Network Card LocalView Network Address Translation A nutshellIP Addresses IP Port See -5,p Adjusting a Unit’s IP Settings for NAT Setting a Router’s Mappings Network device mappings Dynamic Host Configuration Protocol To Configure Dhcp Using Microsoft’s Server2000 orNetwork administrator needs for using Dhcp with DNS Updating a Units Connection Choosing the Computer Name or a Static IP IP Address boxNetwork without Dhcp More about Dhcp Setting up many connections is optional Many Connections to a UnitTo Specify Dial-up and Network Connections Primary connection RAS Server Planning to Connect to One Unit at a Time Connection that behaves like dial-up What your network administrator needsTo Set a Connection to a RAS 14. RAS Servers Telephone Number and PPP Information Using a RAS Server before Connecting to a Unit RAS server may not be needed by your organizationPlanning to connect to many units Preparation About Admin’s naming convention for connections Connections Report and CustomizationAutomatic Naming of Connections Changing the Automatic Suffix in a Connections Name Cascading Alarm Stations Firewall Technical Note To Sequence a Site’s Alarm Stations Quickly Assigning a Site to Many Alarm StationsSetting a Site to Not Report Alarms to a Specific Station Using the Update Site windows Customizing a Dial-Up Connection to an Alarm Station To Customize the Dial-up Connection to an Alarm Station To Cancel the Customization of a Telephone Number Unit Configuration Basics Maintenance SessionUsing View Using a Maintenance Session To Start a Maintenance Session Support for Older Models of Units Site registration First Maintenance SessionMaking a Site Operational Crucial settings for reporting on video of events Unit’s Time Zone and ClockSecurity considerations Scheduling options Time zone To Indicate the Time Zone of a Multi-Media UnitConflicting Time Zones Sntp Setting the Clock Automatically Auto-synch statistics System Clock Manual Setting Adjusting the Clock on a PC Running Rapid Eye SoftwareUsing a PC’s Clock to Set a Unit’s Clock Manually Click Set Multi-Media Unit’s Clock Adjusting the Time on an Operational Unit Correcting the Clock Rebooting a Unit Lack of reasons to reboot a Multi-Media unitAutomatic reboot of Multi-Media unit Securing a Site Maintenance Reference Ending MaintenanceUsing Apply Maintenance Topics Maintenance Tasks Feedback Box Reference Video Feed Setup CamerasRenaming a Camera Automatic detection Adjusting a Video Feed To Re-enable One Cameras FeedTo Re-enable All Newly Connected, Powered Cameras To Adjust All Cameras at Once Other Video Settings Recording settingsSmoothing video Motion Recording Video Continuous Recording Settings To Enable the Recording of a Video FeedMaking use of a Maintenance Session Screen area size of camera windows on a PC monitor Customizing Settings for Recorded Video Resolution SettingMaking settings Forecasting results To Duplicate Settings Frame Rate SettingQuality Setting Continuous Recording and Event Recording Estimating Storage Capacity Optimizing Recorded Video Automatic Maximization of DSP PerformanceRapid Eye Storage Estimator Preparation contiguous connections Automatic display of Maximization tool Manual display of Maximization window Enhanced Preview of ResolutionMaking Optimized Resolution and Frame Rate Settings Resolution Tips 10. The Enhanced Preview Window Comparing the Resolutions of Recorded Video 12. Using Low Resolution, 160 x 120 Ntsc to Show Presence Security and Presence Screen area size of camera windows on a PC monitor Camera Tips for Identification Quality and Resolution Resolution Gauge for Retrieval Session PAL gauge Ntsc gaugeContinuous Recording and Event Recording Resolution Reference Recorded Video ResolutionComment Gauge in a Retrieval Session‡ Customizing Windows for a PC Monitor’s Settings Using Microsoft WindowsUsing two monitors and running View software PC Monitor’s Refresh Rate Larger Monitors and Microsoft Windows Preventive measures Environmental Interference for Video FeedsPhysical Compromise Pan, Tilt, and Zoom PTZ Setup Serial Device Settings for PTZ Acuix dome camera domes Video Tab Settings for PTZTo Assign and Set a New PTZ Device To Enable a PTZ Camera Using a PTZ Camera To Display the PTZ Dartboard Control Click Zonal PTZ Control Mode Using the Dartboard ControlToggling between Zonal Mode and Pull Mode Using Zonal Mode Pulling the Rubber-Band To Configure a Preset on a PTZ Camera Programming a PTZ Dome CameraAuto-focus Auto-iris To Test a Preset Programming a PTZ Preset Behavior of PTZ After a Session Closes PTZ and motion detectionUltrak KD6i domes Kalatel domes PTZ and motion search Constant panning and video archiveUltrak KD6i dome restriction Do not use the Return To Auto-Iris on Ultrak KD6i domes Support for RapidDome PTZ Features RapidDome PTZ Tours To Test a Mimic Tour on a RapidDome Camera RapidDome Preset TourRapidDome Mimic Tour To Setup a Tour of Presets on a RapidDome Camera To Set a Privacy Zone Testing a Preset Tour on a RapidDome CameraPrivacy Zones for RapidDome Configuring the Intellibus Device for a Rapid Eye Unit Acuix Dome Camera To Configure an Acuix Dome Camera for PTZ Use Backing Up an Acuix Configuration File to a PCCommands in the Manage Files dialog box Discovery of Acuix Dome Cameras Downloading a Configuration File to an Acuix Dome Camera Using LocalView Identifying the Model of the Camera Upgrading the Firmware of an Acuix Dome Camera Enhancing Video for Security Event Recording ConfigurationUsing Higher Settings for Video Recorded During an Event Setting Lower Values for Continuous Recording Event Recording on Demand, Using the Boost Button Events of Interest examples Scheduling ConfigurationAutomating Event Recording Events of Interest Data streams AlarmsAudio feeds Customizing a Schedule Making Use of a ScheduleTo Add a Schedule Using a 15-minute Increment in a Schedule Customizing the Default scheduleTo Assign a Schedule to a Camera, or Group of Cameras Renaming cameras To Delete a Schedule Alarms and SchedulingTo Rename a Schedule Holiday and Exception Key facts To correct a date To update a Name or a Type of holiday/exceptionAdding Holidays and Exceptions Event Recording for Video Scheduling a Response Trigger an Event of Interest Checklist for Setting a Rule in the Response Schedule Displaying the Response Panel Used for Making Rules Rule Status Icons Flexibility of checklistRenaming a Rule Alarm and Log to report a response Managing the Response to a RuleAssigning a Schedule to a Response Rule Disabling a Response Rule 11. Motion Detection Configuration Detection scenarios Motion Detection To Configure Motion Detection Customizing Detection MaskingExample Masking an Area of the Video Feed Masking movement that is of no concern Solutions Video settings and motion detectionTo Mask Part of a Video Feed from Motion Detection False Positives Motion Detection Reference CommandsExtra motion detection commands Comparing Motion Detection and Motion Search Motion SearchCamera Sabotage Detection Forty-eight seconds To Configure CSDCalibration of CSD Moved-type CSD Learning and Rearming Alarms Computing the Length of the Video Archive Rapid Eye Storage Estimator What to watch out forEstimates Estimate from a units statistics Number of Cameras, Audio Audio Scheduling Cameras Frame Rate for Continuous RecordingQuality Video compression Quality Pan, tilt, and zoom ResolutionUsing higher resolution Using Higher Values When Recording Video Multi-Media Unit’s Storage Statistics Other statistics about the video archive To Obtain a Unit’s StatisticsStorage Statistics for a Multi-Media Unit Label Meaning Purpose Configuring Other HardwareClearing Storage Preventing Users from Clearing Storage To clear a unit’s storageClearing a stream To change the name of a stream Security and unit availability considerations Updating Security on a Multi-Media UnitTo Trace the Clearing of Storage System Files To Download a File from a Multi-Media UnitRemoving a site after updating security Purpose System Log To upload a file to a Multi-Media unit Double check that you are uploading the correct file System Tab in a Maintenance Session Logging System MessagesSystem Monitor Multi-Media unit registration Making the Fault Relay Operational Camera Signal Format LAN/WAN Communications Changing a Unit’s Network SettingsDefault Network Communications Settings Box Value Default System Values for a Multi-Media Unit System Tab Default Values Box Group Name of Box / ButtonChanging the Maximum Network Data Rate TCP Ports Serial Device Modem Viewing/Changing Modem SettingsModem settings PPP IP Settings Reserved for Modem Connection To Set an External Modem PTZ device settings Serial Device PTZHardware Report To Assign and Set a PTZ Device Color bars Public Display Monitor Using Monitor OutputExternal Hardware Control of a Public Display Monitor Using LocalView As an Additional Public Display Monitor Customer Data and Customer-Device Events Adding a Customer Device That Sends Data to a Unit Adding an Event Rule for a Data-recording Device 10. Some Devices can Be Searched for Data such as No Sale Search Rule and Regular Expressions Reference NetPIT and PIT Devices Support for Protocol Interface Translators Audio Hardware When listeningMulti Audio Using Multi Audio Audio InterferenceAudio with LocalView Monitor and record Events Simultaneous Sessions From One Unit Simultaneous Use of Many Units by One Operator Audio broadcast Users Key Facts Default User Before Creating User Accounts User Management Local User Management Central User Management Account for accessing all units Adding an Account, Using Admin and ViewSetting a Unit to Central User Management Naming Restrictions Extras Account for accessing one unit Adding an Account in LocalViewUser Groups Updating an Account To Customize the Rights in an Account Granting RightsUpdating an Account in LocalView To Deny Access Denying access to all Multi-Media units AdminTo Base Rights On Those of Another User User Rights and Security To Delete an Account Used Onsite, to Access LocalView Denying access to LocalView, onsiteRemoving a Users Account Local User Management Security for a Multi-Media System Security OptionsSecuring the Multi System Security outlook Additional security for some installations Security PrioritiesFrom minimal security to maximum security Security Priorities Priority Action Limiting the Use of Admin To Limit Access to Admin DocumentationPassword Guidelines Features Password Tip PasswordsUsing text securely in Multi password boxes SQL-server Type Logon, Reserved for Multi Operators Multi Database SecuritySQL-Server Option System Password A nutshell keeping unauthorized users out Do not use multiple Multi databases Road Map to Setting the System PasswordAlways update security on all units Extra steps in some system password scenarios Changing the System Password, Part 1 of 3 Using AdminChanging System Password, Part 2 Multi-Media Units Removing a System Password Changing System Password, Part 3 Updating UsersSystem password and security status Status Report After Removing a System Password Remove From All Units Remove on One of Many Units System Password Extras Replacing a Unit To Replace a Unit when a System Password Is in Force If the site cannot be accessed Last Valid Password Last valid system passwordFailure to run a Maintenance Session If a Used Unit Comes from Another Multi System Document K14392V1 Rev a 175 07/07 User Password To Check if the Correct System Password Was TypedAdministrator Password User password technical note To Set the Administrator Account’s Password Password independenceSharing the Administrator account Basic security Rights of User Accounts What you want to avoid To View the Rights of a User and the Sites He may Access Guidelines Right to Use Admin To Grant Access to AdminRight to Use Maintenance Click Rights and site access are based on Why limit the use of maintenance? Right to Use View Right to Access a Site To Define an Account’s Access to Certain SitesWhy limit the use of View? Why deny or limit access to a site? Limiting the Time that a Unit Can Be Used To Limit Use of Cameras Camera Partitioning Physical compromise Preventive measures a short checklistHigh-Security Considerations Security Happenstance Situation Preventive and / or Last Resort MeasuresCompromising video recording Countermeasures Compromising response to an alarm Compromising and locking-out a Multi SA Preferences Setting an Event to Trigger an Alarm or to Be LoggedEvents Defined Setting an Alarm To Set an Event to Report an AlarmWho can set alarms? To set alarms, two items must be part of the user’s account Who can receive alarms? Logging an Event Event Reference Outside World Event Default Settings for Log and Alarm Source Tracing Events Common sense Event Session to Search the Log of Events 17. Search for Events Window To Set the Date of a Retrieval Using the Calendar Utility System FailureTo Input Times and Dates Results Multi-Media Alarm Station Alarm Notification Response Priority Denying Access Best solutionPPP Connectivity Rogue user scenarios Dealing with an open Maintenance Session To Stop a Session on a Networked Multi-Media UnitStopping sessions on units that use modems Outside hackers Denying Access To Deny Access to a User of Your Multi System Using Windows Explorer to delete Multi files Removing Multi-Media SoftwareIneffective strategies for an unwanted user Click Control Panel Double-clickAdd/Remove ProgramsPage Overview Multi-Media Alarm StationsWhere we are Checklist to Configure a Multi-Media Alarm Station System Administrator NeedsOperator Needs Multi SA Needs Adding an Alarm Station Name and Reports To reduce complexity add alarm station definitionsIdentifying and Defining a Connection To reduce complexity further PPP Fields in an Alarm Station’s Definition ScopeGeneral case PPP fields can be left blank Network Connection to an Alarm Station To Setup a Network Connection to an Alarm Station Network Address Translation for Alarm Stations Mapping IP port in network’s router To Prepare a Multi-Media Unit for NAT, Using Admin Enable Use Network Address Translation Dial-up Connection to an Alarm Station Preparing a Dial-up Connection to an Alarm StationModem Microsoft Windows To Setup a Dial-up Connection to an Alarm Station Entering Area Codes in Site and Alarm Station Definitions Customizing a Dial-Up Connection to an Alarm Station Irregular area code use To View Update Station to Call in Case of Alarms To Delay the Speed of DialingTo Use a Local Call Across Area Codes Toll-Free Numbers To Delay the Extension Suffix International Dial-upTelephone exchange at a Rapid Eye site Planning for a few international units To Change Long-distance Prefixes Alarm station for many international unitsCreating extra alarm station definitions RAS Connection to an Alarm Station To Setup a Connection to a RAS Server Honeywell recommends using dialing same countryTech note process of a dial-up callback Customizing a RAS dial-up Making an Alarm Station Operational Using More than one Alarm StationCreating Extra Alarm Station Definitions for the same PC Disconnection Note Removing an Alarm Station Alarms from a De-listed or Unregistered UnitTo List Successful Alarm Callbacks after an Interruption To Trace the Unit Sending the Alarm To Set a Site to Not Report to a Specific Alarm Station Precaution Before defining a site tour Preliminary ChecklistTouring Many Sites Default Amount of Time to Display a Unit During a Site Tour Adding a Site Tour Customizing a Tour To Change the Order of Sites in a Tour To Change the Time Spent at a Site, During a Tour Removing a Tour To Select Another Connection to a Site, During a TourPage To view the log Alarm LogViewing the Log Sorting the Log Selecting Log Items To Print a List of Alarms Filtering the LogPrinting the Log Archiving the Log To Archive Alarms To Delete AlarmsAlarm Log Data Reference Removing Log Items Database creation MinAdminMulti Database Starting Admin To Start AdminObtaining a Multi db Alternatives Using the Default Multi Db Contrasting Db Engines Using Another Db Converting Converting a Multi database from SQL to AccessTo Use Another Multi Db There may be other databases… Impact on View Using the Admin Logon window to create a databaseCreating a Multi Db To Create an Empty, MS-Access-Compatible Multi Db Naming Restriction An Empty Multi Database Using Microsoft SQL-Server SQL-Server Template Using Admin to Create a SQL-compatible Multi Database Db Based On Another To Make a Copy of a Multi DbSimilarities SQL-Server Multi Db MinAdmin Renaming a Multi DbFor making a copy of a db is not obvious File name of a local db is userid.mdb Upgrades from v4 to v5 are automatic Upgrading a Multi dbUpgrading a Local Database Purpose of a local database Producing a Local Database To Make a Local DatabaseObtaining a local database, not connected to Multi db Examples View Setting the Db For routine use of AdminLogging On First use exception To Set a Multi Db for View Refreshing a Local DatabaseFor routine use of View Local Multi database Deleting a Database To Refresh a Local Database while Running ViewCannot Open Db Protecting the Multi dbPage Index Page System Administrator’s Guide Page Parameters system password Page System Administrator’s Guide Page Page Page Page Page Page Document K14392V1 Rev a 07/07