Manuals / HP / Computer Equipment / Switch

HP R-2A, R-2 MD01, R-3A, R-2 RDR manual

Models: R-2 R-3A R-2 RDR R-2A R-2 MD01

1 88

Download 88 pages 56.69 Kb

Page 5

RPC-2 AND RPC-2A QUICK START	2
RPC-2 MD01 AND RPC-2 RDR QUICK START	5
RPC-3, RPC-3A, AND RPC-5 QUICK START	8

UNPACKING	12
PREPARING THE INSTALLATION SITE	12
POWER	13
POWER ON/OFF STATE	14
POWER UP SEQUENCE	14
CIRCUIT BREAKER	14

RPC-2 AND RPC-2A	19
LOCAL ACCESS USING THE EIA-232 SERIAL CONNECTION	19
OPERATION	20
ACCESSING MAIN MENU	21
CONTROLLING RECEPTACLES	21
CONFIGURATION	22
CHANGE PASSWORD	23
DISABLING A PASSWORD	24
CHANGE OUTLET NAME	24
ENABLE/DISABLE CONFIRMATION	25
ENABLE/DISABLE STATUS MENU	26
RPC-2 MD01 AND RPC-2 RDR	27
LOCAL ACCESS USING THE EIA-232 PORT	27
REMOTE ACCESS USING MODEM CONNECTIONS	28
OPERATION	29
ACCESSING MAIN MENU	29
CONTROLLING RECEPTACLES	30
ACCESSING MAIN MENU VIA MODEM	31
CONFIGURATION	32
CHANGE PASSWORD	33
DISABLING A PASSWORD	34

v

Image 5

HP R-2A, R-2 MD01, R-3A, R-2 RDR manual

Contents

BayTech Manual Publication #U140E125-03 July RPC-2 RDR RPC-3 RPC-3A RPC-5Page Page Page Page ADD User Delete User Change Password Vii 230 VAC, 50/60 Hz, 10 Amp Introduction to the Remote Power Control Switch RPC115 VAC, 50/60 Hz, 15 Amp Operation RPC Series Quick StartRPC-2 and RPC-2A Quick Start Or for the RPC-2A RPC Series Quick Start RPC-2 and RPC-2A RPC-2 RDR RPC-2 MD01 and RPC-2 RDR Quick StartOperation Change Password ConfigurationNetwork port Remote access usingRPC-3, RPC-3A and RPC-5 Quick Start Manage Users Deletion of the admin user is prohibitedOutlet Control 8. Default is no outlets selected Change Password Default password is cr disabledChange Outlet ListLogout Reset UnitUnit Status Unpacking InstallationPreparing the Installation Site Power Circuit Breaker Power ON/OFF StatePower UP Sequence RJ-45 Cables and Adapters CablingRPC RJ-45 control port uses the following signals Computer/Terminal Adapter Crossed 8-pin Modular Cable RPC-2 and RPC-2A Detailed Operation ConfigurationRPC’s main menu allows the user to Controlling Receptacles Detailed Operation and Configuration Select #1, Change Password, and press Enter New Password Key at the Enter Request prompt To return to the RPC prompt, press anyEnable/Disable Confirmation From the configuration menu, select #3Switch, the RPC responds with the option to Change the current status. Default isUsing the EIA-232 Local AccessRPC-2 MD01 and RPC-2 RDR Serial ConnectionRemote Access Using Modem Connections RPC’s main menu allows you to Responding Y for yes turns On Outlet If prompted, enter password. The following main menu appears Outlet RPC Config RPC Outlet Enter Request RPC-3 and RPC-3A and RPC-5 Remote Access Using EIA-232Using Network Port ConnectionOperation Detailed Operation and Configuration And/or password have been enabled, you If this is not an initial setup and usernamePassword. When a successful username And/or password has been entered, the mainTo On in the status menu Responding Y for yes turns On OutletObserve the status of Outlet 3 has changed Outlet users have been added, they too will If this is not an initial setup and optionalShow in the User Management Menu, along With the option to delete usersDelete user Add UserDefault password is cr Enter new password = 8 characters To change outlet access, enter numbers of outlets. If Admin user only via the serial port or Configuration can be performed bySelect #3, Configuration. The following Network port. From the RPC Main MenuDefault Subnet Mask is 0.0.0.0. If you fail Access Default Unit ID is RPC-3Outlet Operation Configuration Menu Disable Outlet Status Display? Y/N Outlet 1, Outlet 2, Outlet 3 . . . Outlet Unique set-up.Default outlet names areName Outlets To return to the configuration menu, press any key Unit status provides vital information about Status. In the event of problems withRPC unit system status, network Interface, logged user status, and outletSystem Status Enter the number of the session to terminate RPC responds Changes Reset the unit to load new configurationStatus Technical Support RPC Series Unit Model RPC Series Unit Serial Number Equipment SetupOutlet OUTLET3 OutletInstructions for Repackaging and Shipping Call BayTech to get a Return Authorization NumberREPACKAGING, Shipping and Returning to the Factory FCC Requirements for the RPC-2 MD01 and RDR FCC Radio Frequency Interface StatementFCC Radio Frequency Interface Statement Appendix a SpecificationsSpecifications Robotic Modems Modem Command SummaryAppendix B Rockwell Chip SET Modems Save modem’s configuration in non-volatile memoryIndication Interpretation Diagnostic LED IndicationsAppendix C Appendix D RPC Troubleshooting GuideProblem Symptom Cause Solution Appendix D RPC Troubleshooting Guide Cont’ Appendix D RPC Troubleshooting Guide Cont’ RPC-2 Appendix E- DrawingsRPC-2A RPC-2 MD01 RPC-2 RDR RPC-3 RPC-3A RPC3/3A/5 Ethernet Board RPC-5 Index Shipping