Introduction to the Remote Power Control Switch RPC | HP R-2A

RPC SERIES OWNER’S MANUAL INTRODUCTION TO THE RPC SERIES

________________________________________________________________________________

INTRODUCTION TO THE REMOTE POWER CONTROL SWITCH (RPC)

The BayTech RPC-Series is a full-featured AC power management solution that provides an easy way to control power of remote equipment. From your office or from anywhere, the RPC will TURN ON, TURN OFF, OR REBOOT remote equipment.

There are six different RPC models. Four models operate at 115 VAC, 15 Amp. Two models operate at 230 VAC, 10 Amp.

115 VAC, 50/60 Hz, 15 Amp

RPC-2:Six receptacles and an EIA-232 connection.

RPC-2 MD01: Six receptacles, EIA-232 connection, and a 2400 bps Modem.

RPC-2 RDR: Six receptacles, EIA-232 connection, and

Ring Detect Reset.

RPC-3:Eight receptacles, Ethernet and EIA-232 connections.

RPC-5:Four receptacles (15 amps per receptacle), Ethernet and EIA-232 connections.

230 VAC, 50/60 Hz, 10 Amp

RPC-2A:Six receptacles and an EIA-232 connection.

RPC-3A:Eight receptacles, Ethernet, and EIA-232 connections.

1

Image 8

HP R-2A, R-3A Introduction to the Remote Power Control Switch RPC, 115 VAC, 50/60 Hz, 15 Amp, 230 VAC, 50/60 Hz, 10 Amp

Contents

RPC-2 RDR RPC-3 RPC-3A RPC-5 BayTech Manual Publication #U140E125-03 JulyPage Page Page Page ADD User Delete User Change Password Vii 230 VAC, 50/60 Hz, 10 Amp Introduction to the Remote Power Control Switch RPC115 VAC, 50/60 Hz, 15 Amp Operation RPC Series Quick StartRPC-2 and RPC-2A Quick Start Or for the RPC-2A RPC Series Quick Start RPC-2 and RPC-2A RPC-2 MD01 and RPC-2 RDR Quick Start RPC-2 RDR Operation Configuration Change Password Network port Remote access usingRPC-3, RPC-3A and RPC-5 Quick Start Manage Users Deletion of the admin user is prohibitedOutlet Control Change Password Default password is cr disabled 8. Default is no outlets selectedChange Outlet List Logout Reset UnitUnit Status Unpacking InstallationPreparing the Installation Site Power Circuit Breaker Power ON/OFF StatePower UP Sequence Cabling RJ-45 Cables and Adapters RPC RJ-45 control port uses the following signals Computer/Terminal Adapter Crossed 8-pin Modular Cable Detailed Operation Configuration RPC-2 and RPC-2A RPC’s main menu allows the user to Controlling Receptacles Detailed Operation and Configuration Select #1, Change Password, and press Enter New Password To return to the RPC prompt, press any Key at the Enter Request prompt From the configuration menu, select #3 Enable/Disable ConfirmationSwitch, the RPC responds with the option to Change the current status. Default is Local Access Using the EIA-232RPC-2 MD01 and RPC-2 RDR Serial Connection Remote Access Using Modem Connections RPC’s main menu allows you to Responding Y for yes turns On Outlet If prompted, enter password. The following main menu appears Outlet RPC Config RPC Outlet Enter Request RPC-3 and RPC-3A and RPC-5 Using EIA-232 Remote AccessUsing Network Port Connection Operation Detailed Operation and Configuration If this is not an initial setup and username And/or password have been enabled, youPassword. When a successful username And/or password has been entered, the main To On in the status menu Responding Y for yes turns On OutletObserve the status of Outlet 3 has changed If this is not an initial setup and optional Outlet users have been added, they too willShow in the User Management Menu, along With the option to delete users Add User Delete user Default password is cr Enter new password = 8 characters To change outlet access, enter numbers of outlets. If Configuration can be performed by Admin user only via the serial port orSelect #3, Configuration. The following Network port. From the RPC Main Menu Default Subnet Mask is 0.0.0.0. If you fail Default Unit ID is RPC-3 Access Outlet Operation Configuration Menu Disable Outlet Status Display? Y/N Outlet 1, Outlet 2, Outlet 3 . . . Outlet Unique set-up.Default outlet names areName Outlets To return to the configuration menu, press any key Status. In the event of problems with Unit status provides vital information aboutRPC unit system status, network Interface, logged user status, and outlet System Status Enter the number of the session to terminate RPC responds Reset the unit to load new configuration Changes Status Technical Support Equipment Setup RPC Series Unit Model RPC Series Unit Serial NumberOutlet OUTLET3 Outlet Instructions for Repackaging and Shipping Call BayTech to get a Return Authorization NumberREPACKAGING, Shipping and Returning to the Factory FCC Radio Frequency Interface Statement FCC Requirements for the RPC-2 MD01 and RDR FCC Radio Frequency Interface Statement Specifications Appendix a Specifications Robotic Modems Modem Command SummaryAppendix B Save modem’s configuration in non-volatile memory Rockwell Chip SET Modems Indication Interpretation Diagnostic LED IndicationsAppendix C Appendix D RPC Troubleshooting GuideProblem Symptom Cause Solution Appendix D RPC Troubleshooting Guide Cont’ Appendix D RPC Troubleshooting Guide Cont’ Appendix E- Drawings RPC-2 RPC-2A RPC-2 MD01 RPC-2 RDR RPC-3 RPC-3A RPC3/3A/5 Ethernet Board RPC-5 Index Shipping