Manuals / HP / Computer Equipment / Switch

HP R-2 RDR, R-2A, R-2 MD01, R-3A manual Appendix E- Drawings, RPC-2

Models: R-2 R-3A R-2 RDR R-2A R-2 MD01

1 88

Download 88 pages 56.69 Kb

Page 79

RPC-SERIES OWNER’S MANUAL

APPENDIX E

APPENDIX E- DRAWINGS

RPC-2

72

Image 79

HP R-2 RDR, R-2A, R-2 MD01, R-3A manual Appendix E- Drawings, RPC-2

Contents

BayTech Manual Publication #U140E125-03 July RPC-2 RDR RPC-3 RPC-3A RPC-5Page Page Page Page ADD User Delete User Change Password Vii 115 VAC, 50/60 Hz, 15 Amp Introduction to the Remote Power Control Switch RPC230 VAC, 50/60 Hz, 10 Amp RPC-2 and RPC-2A Quick Start RPC Series Quick StartOperation Or for the RPC-2A RPC Series Quick Start RPC-2 and RPC-2A RPC-2 RDR RPC-2 MD01 and RPC-2 RDR Quick Start Operation Change Password Configuration RPC-3, RPC-3A and RPC-5 Quick Start Remote access usingNetwork port Outlet Control Deletion of the admin user is prohibitedManage Users List Change Password Default password is cr disabled8. Default is no outlets selected Change Outlet Unit Status Reset UnitLogout Preparing the Installation Site InstallationUnpacking Power Power UP Sequence Power ON/OFF StateCircuit Breaker RJ-45 Cables and Adapters Cabling RPC RJ-45 control port uses the following signals Computer/Terminal Adapter Crossed 8-pin Modular Cable RPC-2 and RPC-2A Detailed Operation Configuration RPC’s main menu allows the user to Controlling Receptacles Detailed Operation and Configuration Select #1, Change Password, and press Enter New Password Key at the Enter Request prompt To return to the RPC prompt, press any Change the current status. Default is From the configuration menu, select #3Enable/Disable Confirmation Switch, the RPC responds with the option to Serial Connection Local AccessUsing the EIA-232 RPC-2 MD01 and RPC-2 RDR Remote Access Using Modem Connections RPC’s main menu allows you to Responding Y for yes turns On Outlet If prompted, enter password. The following main menu appears Outlet RPC Config RPC Outlet Enter Request RPC-3 and RPC-3A and RPC-5 Port Connection Using EIA-232Remote Access Using Network Operation Detailed Operation and Configuration And/or password has been entered, the main If this is not an initial setup and usernameAnd/or password have been enabled, you Password. When a successful username Observe the status of Outlet 3 has changed Responding Y for yes turns On OutletTo On in the status menu With the option to delete users If this is not an initial setup and optionalOutlet users have been added, they too will Show in the User Management Menu, along Delete user Add User Default password is cr Enter new password = 8 characters To change outlet access, enter numbers of outlets. If Network port. From the RPC Main Menu Configuration can be performed byAdmin user only via the serial port or Select #3, Configuration. The following Default Subnet Mask is 0.0.0.0. If you fail Access Default Unit ID is RPC-3 Outlet Operation Configuration Menu Disable Outlet Status Display? Y/N Name Outlets Unique set-up.Default outlet names areOutlet 1, Outlet 2, Outlet 3 . . . Outlet To return to the configuration menu, press any key Interface, logged user status, and outlet Status. In the event of problems withUnit status provides vital information about RPC unit system status, network System Status Enter the number of the session to terminate RPC responds Changes Reset the unit to load new configuration Status Technical Support Outlet Equipment SetupRPC Series Unit Model RPC Series Unit Serial Number Outlet OUTLET3 REPACKAGING, Shipping and Returning to the Factory Call BayTech to get a Return Authorization NumberInstructions for Repackaging and Shipping FCC Requirements for the RPC-2 MD01 and RDR FCC Radio Frequency Interface Statement FCC Radio Frequency Interface Statement Appendix a Specifications Specifications Appendix B Modem Command SummaryRobotic Modems Rockwell Chip SET Modems Save modem’s configuration in non-volatile memory Appendix C Diagnostic LED IndicationsIndication Interpretation Problem Symptom Cause Solution RPC Troubleshooting GuideAppendix D Appendix D RPC Troubleshooting Guide Cont’ Appendix D RPC Troubleshooting Guide Cont’ RPC-2 Appendix E- Drawings RPC-2A RPC-2 MD01 RPC-2 RDR RPC-3 RPC-3A RPC3/3A/5 Ethernet Board RPC-5 Index Shipping