Computer/Terminal Adapter | HP R-2 RDR, R-2A, R-2 MD01, R-3A

RPC SERIES OWNER’S MANUAL CABLING

________________________________________________________________________________

	1	BLUE
	2	ORANGE
	3	BLACK
	4	RED
RJ-45	5	GREEN
	6	YELLOW
	7	BROWN
	8	GRAY

1DCD

2RX

3TX

4DTR

FEMALE DE-9

5GND

6DSR

7RTS

8CTS

Figure 5: Computer/Terminal Adapter
BayTech Part No. 9FRJ45PC-1	Crossed RJ-45 cable is required

Modem Communications: A modem can be connected to the EIA-232 serial port by using a 25MRJ45MD-8 adapter (Figure 6). Several types of modem adapters are available from BayTech. Contact an applications engineer for help in choosing the correct adapter.

Page 24

Image 24

HP R-2 RDR, R-2A, R-2 MD01, R-3A manual Computer/Terminal Adapter

Contents

RPC-2 RDR RPC-3 RPC-3A RPC-5 BayTech Manual Publication #U140E125-03 JulyPage Page Page Page ADD User Delete User Change Password Vii Introduction to the Remote Power Control Switch RPC 115 VAC, 50/60 Hz, 15 Amp230 VAC, 50/60 Hz, 10 Amp RPC Series Quick Start RPC-2 and RPC-2A Quick StartOperation Or for the RPC-2A RPC Series Quick Start RPC-2 and RPC-2A RPC-2 MD01 and RPC-2 RDR Quick Start RPC-2 RDR Operation Configuration Change Password Remote access using RPC-3, RPC-3A and RPC-5 Quick StartNetwork port Deletion of the admin user is prohibited Outlet ControlManage Users Change Password Default password is cr disabled 8. Default is no outlets selectedChange Outlet List Reset Unit Unit StatusLogout Installation Preparing the Installation SiteUnpacking Power Power ON/OFF State Power UP SequenceCircuit Breaker Cabling RJ-45 Cables and Adapters RPC RJ-45 control port uses the following signals Computer/Terminal Adapter Crossed 8-pin Modular Cable Detailed Operation Configuration RPC-2 and RPC-2A RPC’s main menu allows the user to Controlling Receptacles Detailed Operation and Configuration Select #1, Change Password, and press Enter New Password To return to the RPC prompt, press any Key at the Enter Request prompt From the configuration menu, select #3 Enable/Disable ConfirmationSwitch, the RPC responds with the option to Change the current status. Default is Local Access Using the EIA-232RPC-2 MD01 and RPC-2 RDR Serial Connection Remote Access Using Modem Connections RPC’s main menu allows you to Responding Y for yes turns On Outlet If prompted, enter password. The following main menu appears Outlet RPC Config RPC Outlet Enter Request RPC-3 and RPC-3A and RPC-5 Using EIA-232 Remote AccessUsing Network Port Connection Operation Detailed Operation and Configuration If this is not an initial setup and username And/or password have been enabled, youPassword. When a successful username And/or password has been entered, the main Responding Y for yes turns On Outlet Observe the status of Outlet 3 has changedTo On in the status menu If this is not an initial setup and optional Outlet users have been added, they too willShow in the User Management Menu, along With the option to delete users Add User Delete user Default password is cr Enter new password = 8 characters To change outlet access, enter numbers of outlets. If Configuration can be performed by Admin user only via the serial port orSelect #3, Configuration. The following Network port. From the RPC Main Menu Default Subnet Mask is 0.0.0.0. If you fail Default Unit ID is RPC-3 Access Outlet Operation Configuration Menu Disable Outlet Status Display? Y/N Unique set-up.Default outlet names are Name OutletsOutlet 1, Outlet 2, Outlet 3 . . . Outlet To return to the configuration menu, press any key Status. In the event of problems with Unit status provides vital information aboutRPC unit system status, network Interface, logged user status, and outlet System Status Enter the number of the session to terminate RPC responds Reset the unit to load new configuration Changes Status Technical Support Equipment Setup RPC Series Unit Model RPC Series Unit Serial NumberOutlet OUTLET3 Outlet Call BayTech to get a Return Authorization Number REPACKAGING, Shipping and Returning to the FactoryInstructions for Repackaging and Shipping FCC Radio Frequency Interface Statement FCC Requirements for the RPC-2 MD01 and RDR FCC Radio Frequency Interface Statement Specifications Appendix a Specifications Modem Command Summary Appendix BRobotic Modems Save modem’s configuration in non-volatile memory Rockwell Chip SET Modems Diagnostic LED Indications Appendix CIndication Interpretation RPC Troubleshooting Guide Problem Symptom Cause SolutionAppendix D Appendix D RPC Troubleshooting Guide Cont’ Appendix D RPC Troubleshooting Guide Cont’ Appendix E- Drawings RPC-2 RPC-2A RPC-2 MD01 RPC-2 RDR RPC-3 RPC-3A RPC3/3A/5 Ethernet Board RPC-5 Index Shipping

Figure 5: Computer/Terminal Adapter

BayTech Part No. 9FRJ45PC-1