Rockwell Chip SET Modems | HP R-2 RDR, R-2A, R-2 MD01, R-3A guide

RPC-SERIES OWNER’S MANUAL

APPENDIX B

APPENDIX B

MODEM COMMAND SUMMARY (Cont.)

ROCKWELL CHIP SET MODEMS

COMMAND	INTERPRETATION

ATS23=59	Fixed Serial Port Rate (default)

AT&C1	Normal CD Operations (default)

AT&D2	Normal DTR Operations (default)

ATS0=1	Auto answer telephone line in 4 or fewer rings

ATE0	Modem does not display keyboard commands

ATQ1	Place modem into quiet mode

AT&W0

Save modem’s configuration in non-volatile memory

NOTE: To send all of the above at the same time, type the following

command: ATS23=59&C1&D2S0=1E0Q1&W0

67

Image 74

HP R-2 RDR, R-2A, R-2 MD01, R-3A manual Rockwell Chip SET Modems, Save modem’s configuration in non-volatile memory

Contents

RPC-2 RDR RPC-3 RPC-3A RPC-5 BayTech Manual Publication #U140E125-03 JulyPage Page Page Page ADD User Delete User Change Password Vii 230 VAC, 50/60 Hz, 10 Amp Introduction to the Remote Power Control Switch RPC115 VAC, 50/60 Hz, 15 Amp Operation RPC Series Quick StartRPC-2 and RPC-2A Quick Start Or for the RPC-2A RPC Series Quick Start RPC-2 and RPC-2A RPC-2 MD01 and RPC-2 RDR Quick Start RPC-2 RDR Operation Configuration Change Password Network port Remote access usingRPC-3, RPC-3A and RPC-5 Quick Start Manage Users Deletion of the admin user is prohibitedOutlet Control Change Outlet Change Password Default password is cr disabled8. Default is no outlets selected List Logout Reset UnitUnit Status Unpacking InstallationPreparing the Installation Site Power Circuit Breaker Power ON/OFF StatePower UP Sequence Cabling RJ-45 Cables and Adapters RPC RJ-45 control port uses the following signals Computer/Terminal Adapter Crossed 8-pin Modular Cable Detailed Operation Configuration RPC-2 and RPC-2A RPC’s main menu allows the user to Controlling Receptacles Detailed Operation and Configuration Select #1, Change Password, and press Enter New Password To return to the RPC prompt, press any Key at the Enter Request prompt Switch, the RPC responds with the option to From the configuration menu, select #3Enable/Disable Confirmation Change the current status. Default is RPC-2 MD01 and RPC-2 RDR Local AccessUsing the EIA-232 Serial Connection Remote Access Using Modem Connections RPC’s main menu allows you to Responding Y for yes turns On Outlet If prompted, enter password. The following main menu appears Outlet RPC Config RPC Outlet Enter Request RPC-3 and RPC-3A and RPC-5 Using Network Using EIA-232Remote Access Port Connection Operation Detailed Operation and Configuration Password. When a successful username If this is not an initial setup and usernameAnd/or password have been enabled, you And/or password has been entered, the main To On in the status menu Responding Y for yes turns On OutletObserve the status of Outlet 3 has changed Show in the User Management Menu, along If this is not an initial setup and optionalOutlet users have been added, they too will With the option to delete users Add User Delete user Default password is cr Enter new password = 8 characters To change outlet access, enter numbers of outlets. If Select #3, Configuration. The following Configuration can be performed byAdmin user only via the serial port or Network port. From the RPC Main Menu Default Subnet Mask is 0.0.0.0. If you fail Default Unit ID is RPC-3 Access Outlet Operation Configuration Menu Disable Outlet Status Display? Y/N Outlet 1, Outlet 2, Outlet 3 . . . Outlet Unique set-up.Default outlet names areName Outlets To return to the configuration menu, press any key RPC unit system status, network Status. In the event of problems withUnit status provides vital information about Interface, logged user status, and outlet System Status Enter the number of the session to terminate RPC responds Reset the unit to load new configuration Changes Status Technical Support Outlet OUTLET3 Equipment SetupRPC Series Unit Model RPC Series Unit Serial Number Outlet Instructions for Repackaging and Shipping Call BayTech to get a Return Authorization NumberREPACKAGING, Shipping and Returning to the Factory FCC Radio Frequency Interface Statement FCC Requirements for the RPC-2 MD01 and RDR FCC Radio Frequency Interface Statement Specifications Appendix a Specifications Robotic Modems Modem Command SummaryAppendix B Save modem’s configuration in non-volatile memory Rockwell Chip SET Modems Indication Interpretation Diagnostic LED IndicationsAppendix C Appendix D RPC Troubleshooting GuideProblem Symptom Cause Solution Appendix D RPC Troubleshooting Guide Cont’ Appendix D RPC Troubleshooting Guide Cont’ Appendix E- Drawings RPC-2 RPC-2A RPC-2 MD01 RPC-2 RDR RPC-3 RPC-3A RPC3/3A/5 Ethernet Board RPC-5 Index Shipping