Replacing VAN Seat Armrest Pads Figure | Invacare Ranger X RWD

ARMS	SECTION 4

This Section Includes the Following:

Replacing Van Seat Armrest Pads

WARNING

After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result.

REPLACING VAN SEAT ARMREST PADS (FIGURE 1)

1.Remove the locknut and washer from the outside of the armrest pad.

2.Remove the mounting screw securing the armrest pad to the armrest post.

3.Position the new armrest pad so the mounting holes align with the armrest post mounting holes.

4.Secure the armrest pad to the armrest post with the mounting screw, washer and locknut removed in steps 1-2.

NOTE: The mounting screw should be installed fromt he inside of the wheelchair frame.

Armrest Pad

Armrest Pad Mounting Hole

Mounting Screw

ARMS

Armrest Post

Locknut

Mounting Hole

Armrest Post

Washer

FIGURE 1 - REPLACING VAN SEAT ARMREST PADS

Part No. 1104849

25

3G Storm Series® Wheelchairs

Image 25

Invacare Ranger X RWD, Torque SP RWD, Arrow RWD service manual Replacing VAN Seat Armrest Pads Figure, Arms Section

Contents

This Manual Must be Performed by a Dealer Keep this MANUAL. the ProceduresQualified Technician Restraints Seat Positioning Straps Special Notes Table of Contents Seat Frame Electronics Typical Product Parameters Arrow Typical Product Parameters Arrow Parameters Arrow Typical Product Physical Dimensions Typical Product Parameters Torque SP Typical Product Parameters Torque SP Parameters Torque Typical Product Typical Product Parameters Ranger Typical Product Parameters Ranger Parameters Ranger Typical Product Operating Information Repair or Service InformationGeneral Guidelines Section General Guidelines Rain Test General Guidelines Section Batteries Weight Training Warning General Guidelines Section Label LocationTire Pressure Warning Found on side frame near Shipping TIE Down RestraintsBrushless Motor Rear of the chair Troubleshooting Troubleshooting SectionEnsure that power is OFF Section Troubleshooting Motor Testing FigureMotor Brush Inspection Figure Electro Mechanical Parking Brake Testing ELECTRO-MECHANICAL Parking Brake Testing Figure Section Hardware Torque Specifications Hardware Torque SpecificationsStandard Seat Frame Specifications Hardware Torque Hardware Torque Specifications SectionVAN Seat Asba Adjustable Seat Back Angle Front Base Frame Conventional MOTOR/GEARBOX Base Frame Heavy Duty GEARLESS/BRUSHLESS Motor Arms Section Replacing VAN Seat Armrest Pads FigureArms Section UPHOLSTERY/POSITIONING Strap Upholestery Positioning StrapRear of Seat Frame Seat Frame UPHOLSTERY/POSITIONING Strap Section Replacing Back Upholstery FigurePositioning Strap Upholestery Heavy Duty Models Standard Models Seat Frame Seat Frame Section Standard or Section Seat Frame Installing REMOVING/INSTALLING Standard Seat Frame Subassembly FigureReplacing Same Size Standard Seat Frame Removing Standard Seat Frame Changing Seat Depth Repeat Steps 1-3 for the desired seat depth Asba Figure Changing Seat Depth Asba Repeat the Steps 1-9 for the opposite back cane Changing Seat Depth Between 12 and 15-INCHES Figure Changing Seat Width Standard and Asba Steps Detail a Converting from Asba to Standard Seat Frame or VAN Seat Component ReplacementConverting from Standard Seat Frame or VAN Seat to Asba Coved Washer Spacer Center Frame Installing VAN Seat INSTALLING/REMOVING VAN Seat AssemblyReplacing VAN Seat AND/OR VAN Seat Frame Figure Removing VAN Seat Converting from Standard Seat Frame to Asba or Vice Versa Asba Converting from Asba to VAN Seat or Vice Versa REMOVING/INSTALLING Seat PAN Figure Mounting Screws Seat SeatPan Positioning Strap Seat Angle Adjustment Figure Section Base Frame Base Frame Base Frame Section Replacing Seat Support Brackets Figure Replacing Seat Support Brackets Replacing Seat Support Bracket T-NUTS Figure Replacing Battery Charger Bracket and T-NUT Figure Replacing Battery Charger Bracket and T-NUT REMOVING/INSTALLING Seat Stop Screws Figure Installing CJ Back Brackets REMOVING/INSTALLING CJ Back Brackets FigureRemoving CJ Back Brackets Back Frame Section Section Back Frame Removing Installing CJ Back Brackets Changing Back Height Figure Changing Back Height 100 Back Angle Adjustment Section Batteries Batteries Proper Battery to be Used Using the Proper Batteries Figures 1Batteries Section Do not USE GP24 Using the Proper Batteries GP24 INSTALLING/REMOVING Batteries INTO/FROM Battery Boxes Figure DISCONNECTING/CONNECTING Battery Cables DISCONNECTING/CONNECTING Battery Cables Group 24 Batteries TWO 2 Connector ONE 1 Connector Battery BOX Group 24 Batteries on Wheelchairs Built After 1/25/04 Figure DISCONNECTING/CONNECTING Battery Cables Group 24 Batteries 22NF Batteries in Single Battery BOX Figure Rear Detail a StepSteps 3 Steps 5 Charging Batteries Figure When to Charge Batteries FigureMKIV-A and MKIV-RII Joysticks MKIV-A+ Joysticks Required Items Tool Quantity Comments Description of Battery Chargers Torque SP Using Battery Chargers Replacing Batteries Recommended Battery Types Wheelchairs Built Before 1/26/04 Battery Requirements and Weight Limitations Cleaning Battery Terminals REMOVING/INSTALLING Battery Boxes Base FRAMELocked Unlocked Retainer Bar REMOVING/INSTALLING Battery Boxes 22NF Battery Boxes 22NF Battery Boxes Figure Wiring Harness REMOVING/INSTALLING the Wiring HarnessGroup 24 Batteries Figure Harness Wiring 22NF Batteries Figure REMOVING/INSTALLING the Wiring Harness 22NF Batteries Section Wiring Harness Detail a 22NF Batteries Adjusting Limit Switch Adjusting Limit Switch Figure Section Wiring Harness Replacing Retainer Clip Replacing Battery BOX Retainer BAR/RETAINER Clip FigureReplacing Retainer BAR Retention STRAP/RETAINER Section Section Retention STRAP/RETAINER Replacing Battery BOX Retainer BAR/RETAINER Clip Replacing Pneumatic TIRES/TUBES Drive WHEELS/ Casters REMOVING/INSTALLING Drive Wheels FigureWHEELS/MOTORS Section WHEELS/MOTORS 14 X 3-INCH Wheel Section WHEELS/MOTORSConventional Motor GEARLESS/BRUSHLESS Motor With Gearbox 14 X 4-INCH Wheel Wheelchairs Built WHEELS/MOTORS 14 X 4-INCH Wheel REMOVING/INSTALLING Drive Wheel HUB Figure REMOVING/INSTALLING the Adapter Plate with Studs Figure REMOVING/INSTALLING GB Motor Spacer Figure Installing Wheel Lock Bracket Onto Wheelchair Installing Wheel Lock Bracket Onto Wheelchair Figure Mounting screws to 160 in-lbs Flat Free Tires REMOVING/INSTALLING the RIM AND/OR Tire Figure Removing Casters REMOVING/INSTALLING Casters FigureShock Fork Inch Fork Hardware Orientation Replacing Forks Figure Installing Casters Installing the Motor REMOVING/INSTALLING the MotorConventional Motor with Gearbox Figure Conventional Motor Gearbox Standard GEARLESS/BRUSHLESS Motor Before 1/26/04 Figure Suspension Arm Heavy Duty GEARLESS/BRUSHLESS Motor Figure Wiring Harness from Controller Connects to the Motor Here Pole Motors Figure INSTALLING/REMOVING Fenders WHEELS/MOTORS Standard GEARLESS/BRUSHLESS Motors Before 1/26/04 Figure Or Tire in this section Heavy Duty GEARLESS/BRUSHLESS Motors Figure Electronics Repositioning Mkiv Joystick VAN Seat Models FigureSection Electronics Electronics Section REMOVING/INSTALLING the Mkiv Controller 102 103 GB Controller 105 Lockwasher 107 Lockwashers Recliner Section Positioning Limit Switch FigureRecliner Section Recliner Adjusting Limit Switch Figure Position Over 105 Relative to Replacing Recliner Cable Assemblies Figure Replacing Recliner Cable Assemblies Replacing GAS Cylinder REPLACING/ADJUSTING GAS Cylinders Figure Adjusting GAS Cylinder Mounting bracket of the back cane Locknut through the back caneNylon washer, mounting hole TOP of the gas cylinder, nylon washer REMOVING/INSTALLING the Seat REMOVING/INSTALLING the Seat PANChanging Seat Depth Figure Back Canes and Spreader BAR Seat Width Ranges Changing Seat Width REMOVING/INSTALLING Battery Boxes in of this manual RWD Wheelchairs Section REMOVING/INSTALLING Group 24 Battery BOX SUB-FRAME FigureRWD Wheelchairs Front of Chair Section RWD Wheelchairs Remove the battery box. Refer to REMOVING/INSTALLING 22NF Battery BOX Tray FigureRemoving 22NF Components Figure Wheelchairs Equipped with Vent Tray Installing Group 24 Components Figure Steps 4 Installing Group 24 Components Group 24 Batteries Figures 5 Shock or Rubber Element Replacement RWD Wheelchairs Wheelchairs Equipped with Vent Tray TOP of Shock or Rubber ElementFront Chair Rear Wheelchairs Without Vent Tray Bottom of Shock or Rubber Element 22NF Batteries Figures 6Rubber Element Anti-tip bracket Install the 22NF battery box. Refer to Shock Spring Replacement Figure There is no need to remove shock from suspension arm Shock Spring Replacement REMOVING/INSTALLING Drive Wheel Hubs in of this manual REMOVING/INSTALLING Gearbox FigureWheelchairs Adjustment Options Adjusting Weight Distribution FigureAdjusting Weight Distribution Procedure Repositioning the Motor MOTOR/GEARBOX AssemblyRepositioning the MOTOR/GEARBOX Figure Repeat Steps 3-5 for opposite side of the wheelchair Forward Arrow and Ranger X with Fixed Back Before 1/26/04 Inch Forward N/A Repositioning the Heavy Duty GEARLESS/BRUSHLESS Motor Figure Remove plug buttons from the middle of the base frame Suspension ARM for REMOVING/INSTALLINGWheelchairs with Gearless REMOVING/INSTALLING the 3-INCH ANTI-TIP Assembly Figure ANTI-TIPPER Wheel Replacement FigureRWD 138 Warranty Warranty Canada One Invacare Way