Parameters Arrow Typical Product | Invacare Ranger X RWD, Arrow RWD

TYPICAL PRODUCT PARAMETERS - ARROW

TYPICAL PRODUCT PARAMETERS - ARROW

		PHYSICAL DIMENSIONS

CASTERS W/PRECISION SEALED BEARINGS
SEMI-PNEUMATIC:
Standard:					8 X 2¼-inches
Option:				6 X 2-inches (w/ shock fork)

PNEUMATIC OR FOAM FILLED:
Standard:					8 X 2-inches
Option:					9 X 2¾-inches

ANTI-TIPPERS (3-INCH WHEELS):					Standard

CASTER FORKS:				Standard, Shock Fork (Optional)

FOOTRESTS:				Telescoping Front Rigging Supports,
				Swing-Away (Std), Heavy Duty (Opt.),
				2-in. and 4-in. longer Pivot Slide Tube (Opt)

ARMRESTS:				Flip Back, Fixed or Adjustable Height
				(Desk and Full Length)

SEAT ANGLE ADJUSTMENT:				Adjustable (0o to 10o)

SEAT CUSHION:					Cushion (Optional)

CHAIR UPHOLSTERY OPTIONS:					Nylon

BATTERY REQUIREMENTS:				See chart on page 70

WEIGHT LIMITATIONS:
Arrow with gearless/brushless motor (after 1/25/04)					up to 400 lbs
Arrow with gearless/brushless motor (before 1/26/04)					up to 300 lbs
Arrow with 4 pole motor					up to 400 lbs


		PERFORMANCE BEFORE 1/26/04
RATING			SPEED				RANGE
		G/B MOTOR		4 POLE MOTOR

300 lbs		up to 8 mph		N/A			up to 29 miles

400 lbs		N/A		up to 4.5 mph			up to 19 miles


		PERFORMANCE AFTER 1/25/04
RATING			SPEED				RANGE
		G/B MOTOR		4 POLE MOTOR

400 lbs		up to 7 mph		N/A			up to 33 miles

Range will vary with battery conditions, surface, terrain and operators weight.

PARAMETERS - ARROW	TYPICAL PRODUCT

Part No. 1104849

7

3G Storm Series® Wheelchairs

Image 7

Invacare Ranger X RWD, Torque SP RWD, Arrow RWD service manual Parameters Arrow Typical Product, Physical Dimensions

Contents

This Manual Must be Performed by a Dealer Keep this MANUAL. the ProceduresQualified Technician Restraints Seat Positioning Straps Special Notes Table of Contents Seat Frame Electronics Typical Product Parameters Arrow Typical Product Parameters Arrow Parameters Arrow Typical Product Physical Dimensions Typical Product Parameters Torque SP Typical Product Parameters Torque SP Parameters Torque Typical Product Typical Product Parameters Ranger Typical Product Parameters Ranger Parameters Ranger Typical Product Section General Guidelines Repair or Service InformationOperating Information General Guidelines Rain Test General Guidelines Section Batteries Weight Training Warning General Guidelines Section Label LocationTire Pressure Warning Rear of the chair Shipping TIE Down RestraintsFound on side frame near Brushless Motor Troubleshooting Troubleshooting SectionEnsure that power is OFF Section Troubleshooting Motor Testing FigureMotor Brush Inspection Figure Electro Mechanical Parking Brake Testing ELECTRO-MECHANICAL Parking Brake Testing Figure Section Hardware Torque Specifications Hardware Torque SpecificationsStandard Seat Frame Specifications Hardware Torque Hardware Torque Specifications SectionVAN Seat Asba Adjustable Seat Back Angle Front Base Frame Conventional MOTOR/GEARBOX Base Frame Heavy Duty GEARLESS/BRUSHLESS Motor Arms Section Replacing VAN Seat Armrest Pads FigureArms Seat Frame Upholestery Positioning StrapSection UPHOLSTERY/POSITIONING Strap Rear of Seat Frame UPHOLSTERY/POSITIONING Strap Section Replacing Back Upholstery FigurePositioning Strap Upholestery Heavy Duty Models Standard Models Seat Frame Seat Frame Section Standard or Section Seat Frame Removing REMOVING/INSTALLING Standard Seat Frame Subassembly FigureInstalling Replacing Same Size Standard Seat Frame Standard Seat Frame Changing Seat Depth Repeat Steps 1-3 for the desired seat depth Asba Figure Changing Seat Depth Asba Repeat the Steps 1-9 for the opposite back cane Changing Seat Depth Between 12 and 15-INCHES Figure Changing Seat Width Standard and Asba Steps Detail a Converting from Asba to Standard Seat Frame or VAN Seat Component ReplacementConverting from Standard Seat Frame or VAN Seat to Asba Coved Washer Spacer Center Frame Removing VAN Seat INSTALLING/REMOVING VAN Seat AssemblyInstalling VAN Seat Replacing VAN Seat AND/OR VAN Seat Frame Figure Converting from Standard Seat Frame to Asba or Vice Versa Asba Converting from Asba to VAN Seat or Vice Versa REMOVING/INSTALLING Seat PAN Figure Mounting Screws Seat SeatPan Positioning Strap Seat Angle Adjustment Figure Section Base Frame Base Frame Base Frame Section Replacing Seat Support Brackets Figure Replacing Seat Support Brackets Replacing Seat Support Bracket T-NUTS Figure Replacing Battery Charger Bracket and T-NUT Figure Replacing Battery Charger Bracket and T-NUT REMOVING/INSTALLING Seat Stop Screws Figure Back Frame Section REMOVING/INSTALLING CJ Back Brackets FigureInstalling CJ Back Brackets Removing CJ Back Brackets Section Back Frame Removing Installing CJ Back Brackets Changing Back Height Figure Changing Back Height 100 Back Angle Adjustment Section Batteries Batteries Do not USE Using the Proper Batteries Figures 1Proper Battery to be Used Batteries Section GP24 Using the Proper Batteries GP24 INSTALLING/REMOVING Batteries INTO/FROM Battery Boxes Figure DISCONNECTING/CONNECTING Battery Cables DISCONNECTING/CONNECTING Battery Cables Group 24 Batteries TWO 2 Connector ONE 1 Connector Battery BOX Group 24 Batteries on Wheelchairs Built After 1/25/04 Figure DISCONNECTING/CONNECTING Battery Cables Group 24 Batteries 22NF Batteries in Single Battery BOX Figure Steps 5 StepRear Detail a Steps 3 MKIV-A+ Joysticks When to Charge Batteries FigureCharging Batteries Figure MKIV-A and MKIV-RII Joysticks Required Items Tool Quantity Comments Description of Battery Chargers Torque SP Using Battery Chargers Replacing Batteries Recommended Battery Types Wheelchairs Built Before 1/26/04 Battery Requirements and Weight Limitations Cleaning Battery Terminals REMOVING/INSTALLING Battery Boxes Base FRAMELocked Unlocked Retainer Bar REMOVING/INSTALLING Battery Boxes 22NF Battery Boxes 22NF Battery Boxes Figure Wiring Harness REMOVING/INSTALLING the Wiring HarnessGroup 24 Batteries Figure Harness Wiring 22NF Batteries Figure REMOVING/INSTALLING the Wiring Harness 22NF Batteries Section Wiring Harness Detail a 22NF Batteries Adjusting Limit Switch Adjusting Limit Switch Figure Section Wiring Harness Retention STRAP/RETAINER Section Replacing Battery BOX Retainer BAR/RETAINER Clip FigureReplacing Retainer Clip Replacing Retainer BAR Section Retention STRAP/RETAINER Replacing Battery BOX Retainer BAR/RETAINER Clip WHEELS/MOTORS REMOVING/INSTALLING Drive Wheels FigureReplacing Pneumatic TIRES/TUBES Drive WHEELS/ Casters WHEELS/MOTORS Section 14 X 4-INCH Wheel Wheelchairs Built Section WHEELS/MOTORS14 X 3-INCH Wheel Conventional Motor GEARLESS/BRUSHLESS Motor With Gearbox WHEELS/MOTORS 14 X 4-INCH Wheel REMOVING/INSTALLING Drive Wheel HUB Figure REMOVING/INSTALLING the Adapter Plate with Studs Figure REMOVING/INSTALLING GB Motor Spacer Figure Installing Wheel Lock Bracket Onto Wheelchair Installing Wheel Lock Bracket Onto Wheelchair Figure Mounting screws to 160 in-lbs Flat Free Tires REMOVING/INSTALLING the RIM AND/OR Tire Figure Inch Fork Hardware Orientation REMOVING/INSTALLING Casters FigureRemoving Casters Shock Fork Replacing Forks Figure Installing Casters Conventional Motor Gearbox REMOVING/INSTALLING the MotorInstalling the Motor Conventional Motor with Gearbox Figure Standard GEARLESS/BRUSHLESS Motor Before 1/26/04 Figure Suspension Arm Heavy Duty GEARLESS/BRUSHLESS Motor Figure Wiring Harness from Controller Connects to the Motor Here Pole Motors Figure INSTALLING/REMOVING Fenders WHEELS/MOTORS Standard GEARLESS/BRUSHLESS Motors Before 1/26/04 Figure Or Tire in this section Heavy Duty GEARLESS/BRUSHLESS Motors Figure Electronics Repositioning Mkiv Joystick VAN Seat Models FigureSection Electronics Electronics Section REMOVING/INSTALLING the Mkiv Controller 102 103 GB Controller 105 Lockwasher 107 Lockwashers Recliner Section Positioning Limit Switch FigureRecliner Section Recliner Adjusting Limit Switch Figure Position Over 105 Relative to Replacing Recliner Cable Assemblies Figure Replacing Recliner Cable Assemblies Replacing GAS Cylinder REPLACING/ADJUSTING GAS Cylinders Figure Adjusting GAS Cylinder TOP of the gas cylinder, nylon washer Locknut through the back caneMounting bracket of the back cane Nylon washer, mounting hole REMOVING/INSTALLING the Seat REMOVING/INSTALLING the Seat PANChanging Seat Depth Figure Back Canes and Spreader BAR Seat Width Ranges Changing Seat Width REMOVING/INSTALLING Battery Boxes in of this manual RWD Wheelchairs Section REMOVING/INSTALLING Group 24 Battery BOX SUB-FRAME FigureRWD Wheelchairs Front of Chair Section RWD Wheelchairs Remove the battery box. Refer to REMOVING/INSTALLING 22NF Battery BOX Tray FigureRemoving 22NF Components Figure Wheelchairs Equipped with Vent Tray Installing Group 24 Components Figure Steps 4 Installing Group 24 Components Group 24 Batteries Figures 5 Shock or Rubber Element Replacement Wheelchairs Without Vent Tray TOP of Shock or Rubber ElementRWD Wheelchairs Wheelchairs Equipped with Vent Tray Front Chair Rear Anti-tip bracket 22NF Batteries Figures 6Bottom of Shock or Rubber Element Rubber Element Install the 22NF battery box. Refer to Shock Spring Replacement Figure There is no need to remove shock from suspension arm Shock Spring Replacement REMOVING/INSTALLING Drive Wheel Hubs in of this manual REMOVING/INSTALLING Gearbox FigureWheelchairs Adjustment Options Adjusting Weight Distribution FigureAdjusting Weight Distribution Procedure Repeat Steps 3-5 for opposite side of the wheelchair MOTOR/GEARBOX AssemblyRepositioning the Motor Repositioning the MOTOR/GEARBOX Figure Forward Arrow and Ranger X with Fixed Back Before 1/26/04 Inch Forward N/A Repositioning the Heavy Duty GEARLESS/BRUSHLESS Motor Figure Remove plug buttons from the middle of the base frame Suspension ARM for REMOVING/INSTALLINGWheelchairs with Gearless REMOVING/INSTALLING the 3-INCH ANTI-TIP Assembly Figure ANTI-TIPPER Wheel Replacement FigureRWD 138 Warranty Warranty Canada One Invacare Way