Invacare Ranger X RWD, Torque SP RWD, Arrow RWD specs

WHEELS/MOTORS

SECTION 12	WHEELS/MOTORS

REMOVING/INSTALLING THE RIM AND/OR TIRE (FIGURE 6)

NOTE: This procedure is for wheelchairs equipped with heavy duty gearless/brushless motors before 1/26/04 and standard gearless/brushless motors after 1/25/04.

REMOVING

1.Remove the battery boxes. Refer to REMOVING/INSTALLING BATTERY BOXES in SECTION 9 of this manual.

WARNING

If wheelchair is equipped with pneumatic tires, deflate tire BEFORE removing rim - otherwise serious personal injury and damage will result.

2.If the wheelchair is equipped with pneumatic tires, deflate the tire.

3.Remove the five (5) mounting screws that secure the rim to the gearless/brushless motor.

4.Remove the rim and tire from the gearless/brushless motor.

INSTALLING

1.Perform one (1) of the following:

A.Pneumatic Tires - Secure new/existing rim and new/existing pneumatic tire [w/ new tube (if applicable)] to the gearless/brushless motor and torque the five

(5) mounting screws to 160 in-lbs.

B.Flat Free Tires

NOTE: In order to install the tire with flat free properly, the tire must be compressed to a certain point to allow the use of the 16 mm length mounting screws. This is accomplished by first using three (3) 25 mm length mounting screws threaded in every other mounting hole. The longer mounting screws are not to be threaded completely into the GB motor. They are to be threaded 1/4-inch only to provide compression of the tire.

DETAIL “A”

M8-1-1/4-25mm Mounting Screw

Gearless/

Brushless

TireMotor

Five (5)

M8-1-1/4-16mm

Mounting Screws

Rim

FIGURE 6 - REMOVING/INSTALLING THE RIM AND/OR TIRE

3G Storm Series® Wheelchairs

88

Part No. 1104849

Image 88

Invacare Ranger X RWD REMOVING/INSTALLING the RIM AND/OR Tire Figure, Mounting screws to 160 in-lbs Flat Free Tires

Contents

This Manual Must be Performed by a Dealer Keep this MANUAL. the ProceduresQualified Technician Special Notes Restraints Seat Positioning Straps Table of Contents Seat Frame Electronics Typical Product Parameters Arrow Typical Product Parameters Arrow Physical Dimensions Parameters Arrow Typical Product Typical Product Parameters Torque SP Typical Product Parameters Torque SP Parameters Torque Typical Product Typical Product Parameters Ranger Typical Product Parameters Ranger Parameters Ranger Typical Product Repair or Service Information Operating InformationGeneral Guidelines Section General Guidelines General Guidelines Section Batteries Rain Test Weight Training Warning General Guidelines Section Label LocationTire Pressure Warning Shipping TIE Down Restraints Found on side frame nearBrushless Motor Rear of the chair Troubleshooting Troubleshooting SectionEnsure that power is OFF Section Troubleshooting Motor Testing FigureMotor Brush Inspection Figure ELECTRO-MECHANICAL Parking Brake Testing Figure Electro Mechanical Parking Brake Testing Section Hardware Torque Specifications Hardware Torque SpecificationsStandard Seat Frame Specifications Hardware Torque Hardware Torque Specifications SectionVAN Seat Asba Adjustable Seat Back Angle Base Frame Conventional MOTOR/GEARBOX Front Base Frame Heavy Duty GEARLESS/BRUSHLESS Motor Arms Section Replacing VAN Seat Armrest Pads FigureArms Upholestery Positioning Strap Section UPHOLSTERY/POSITIONING StrapRear of Seat Frame Seat Frame UPHOLSTERY/POSITIONING Strap Section Replacing Back Upholstery FigurePositioning Strap Upholestery Standard Models Heavy Duty Models Seat Frame Section Seat Frame Section Seat Frame Standard or REMOVING/INSTALLING Standard Seat Frame Subassembly Figure InstallingReplacing Same Size Standard Seat Frame Removing Changing Seat Depth Standard Seat Frame Asba Figure Repeat Steps 1-3 for the desired seat depth Changing Seat Depth Asba Changing Seat Depth Between 12 and 15-INCHES Figure Repeat the Steps 1-9 for the opposite back cane Changing Seat Width Standard and Asba Detail a Steps Converting from Asba to Standard Seat Frame or VAN Seat Component ReplacementConverting from Standard Seat Frame or VAN Seat to Asba Coved Washer Spacer Center Frame INSTALLING/REMOVING VAN Seat Assembly Installing VAN SeatReplacing VAN Seat AND/OR VAN Seat Frame Figure Removing VAN Seat Converting from Standard Seat Frame to Asba or Vice Versa Converting from Asba to VAN Seat or Vice Versa Asba REMOVING/INSTALLING Seat PAN Figure Mounting Screws Seat SeatPan Positioning Strap Seat Angle Adjustment Figure Base Frame Section Base Frame Replacing Seat Support Brackets Figure Base Frame Section Replacing Seat Support Bracket T-NUTS Figure Replacing Seat Support Brackets Replacing Battery Charger Bracket and T-NUT Figure REMOVING/INSTALLING Seat Stop Screws Figure Replacing Battery Charger Bracket and T-NUT REMOVING/INSTALLING CJ Back Brackets Figure Installing CJ Back BracketsRemoving CJ Back Brackets Back Frame Section Removing Installing CJ Back Brackets Section Back Frame Changing Back Height Figure Changing Back Height Back Angle Adjustment 100 Batteries Section Batteries Using the Proper Batteries Figures 1 Proper Battery to be UsedBatteries Section Do not USE Using the Proper Batteries GP24 GP24 INSTALLING/REMOVING Batteries INTO/FROM Battery Boxes Figure DISCONNECTING/CONNECTING Battery Cables TWO 2 Connector ONE 1 Connector Battery BOX DISCONNECTING/CONNECTING Battery Cables Group 24 Batteries Group 24 Batteries on Wheelchairs Built After 1/25/04 Figure DISCONNECTING/CONNECTING Battery Cables Group 24 Batteries 22NF Batteries in Single Battery BOX Figure Step Rear Detail aSteps 3 Steps 5 When to Charge Batteries Figure Charging Batteries FigureMKIV-A and MKIV-RII Joysticks MKIV-A+ Joysticks Description of Battery Chargers Required Items Tool Quantity Comments Using Battery Chargers Torque SP Recommended Battery Types Replacing Batteries Battery Requirements and Weight Limitations Wheelchairs Built Before 1/26/04 REMOVING/INSTALLING Battery Boxes Cleaning Battery Terminals Base FRAMELocked Unlocked Retainer Bar 22NF Battery Boxes Figure REMOVING/INSTALLING Battery Boxes 22NF Battery Boxes Wiring Harness REMOVING/INSTALLING the Wiring HarnessGroup 24 Batteries Figure Wiring Harness 22NF Batteries Figure Section Wiring Harness Detail a 22NF Batteries REMOVING/INSTALLING the Wiring Harness 22NF Batteries Adjusting Limit Switch Figure Adjusting Limit Switch Section Wiring Harness Replacing Battery BOX Retainer BAR/RETAINER Clip Figure Replacing Retainer ClipReplacing Retainer BAR Retention STRAP/RETAINER Section Replacing Battery BOX Retainer BAR/RETAINER Clip Section Retention STRAP/RETAINER REMOVING/INSTALLING Drive Wheels Figure Replacing Pneumatic TIRES/TUBES Drive WHEELS/ CastersWHEELS/MOTORS Section WHEELS/MOTORS Section WHEELS/MOTORS 14 X 3-INCH WheelConventional Motor GEARLESS/BRUSHLESS Motor With Gearbox 14 X 4-INCH Wheel Wheelchairs Built REMOVING/INSTALLING Drive Wheel HUB Figure WHEELS/MOTORS 14 X 4-INCH Wheel REMOVING/INSTALLING GB Motor Spacer Figure REMOVING/INSTALLING the Adapter Plate with Studs Figure Installing Wheel Lock Bracket Onto Wheelchair Figure Installing Wheel Lock Bracket Onto Wheelchair REMOVING/INSTALLING the RIM AND/OR Tire Figure Mounting screws to 160 in-lbs Flat Free Tires REMOVING/INSTALLING Casters Figure Removing CastersShock Fork Inch Fork Hardware Orientation Installing Casters Replacing Forks Figure REMOVING/INSTALLING the Motor Installing the MotorConventional Motor with Gearbox Figure Conventional Motor Gearbox Standard GEARLESS/BRUSHLESS Motor Before 1/26/04 Figure Suspension Arm Heavy Duty GEARLESS/BRUSHLESS Motor Figure Wiring Harness from Controller Connects to the Motor Here INSTALLING/REMOVING Fenders Pole Motors Figure WHEELS/MOTORS Standard GEARLESS/BRUSHLESS Motors Before 1/26/04 Figure Heavy Duty GEARLESS/BRUSHLESS Motors Figure Or Tire in this section Electronics Repositioning Mkiv Joystick VAN Seat Models FigureSection Electronics REMOVING/INSTALLING the Mkiv Controller Electronics Section 102 103 GB Controller 105 Lockwasher 107 Lockwashers Recliner Section Positioning Limit Switch FigureRecliner Adjusting Limit Switch Figure Section Recliner Replacing Recliner Cable Assemblies Figure Position Over 105 Relative to Replacing Recliner Cable Assemblies REPLACING/ADJUSTING GAS Cylinders Figure Replacing GAS Cylinder Adjusting GAS Cylinder Locknut through the back cane Mounting bracket of the back caneNylon washer, mounting hole TOP of the gas cylinder, nylon washer REMOVING/INSTALLING the Seat REMOVING/INSTALLING the Seat PANChanging Seat Depth Figure Changing Seat Width Back Canes and Spreader BAR Seat Width Ranges REMOVING/INSTALLING Battery Boxes in of this manual RWD Wheelchairs Section REMOVING/INSTALLING Group 24 Battery BOX SUB-FRAME FigureRWD Wheelchairs Section RWD Wheelchairs Front of Chair Remove the battery box. Refer to REMOVING/INSTALLING 22NF Battery BOX Tray FigureRemoving 22NF Components Figure Installing Group 24 Components Figure Wheelchairs Equipped with Vent Tray Installing Group 24 Components Steps 4 Shock or Rubber Element Replacement Group 24 Batteries Figures 5 TOP of Shock or Rubber Element RWD Wheelchairs Wheelchairs Equipped with Vent TrayFront Chair Rear Wheelchairs Without Vent Tray 22NF Batteries Figures 6 Bottom of Shock or Rubber ElementRubber Element Anti-tip bracket Shock Spring Replacement Figure Install the 22NF battery box. Refer to Shock Spring Replacement There is no need to remove shock from suspension arm REMOVING/INSTALLING Drive Wheel Hubs in of this manual REMOVING/INSTALLING Gearbox FigureWheelchairs Adjustment Options Adjusting Weight Distribution FigureAdjusting Weight Distribution Procedure MOTOR/GEARBOX Assembly Repositioning the MotorRepositioning the MOTOR/GEARBOX Figure Repeat Steps 3-5 for opposite side of the wheelchair Arrow and Ranger X with Fixed Back Forward Before 1/26/04 Repositioning the Heavy Duty GEARLESS/BRUSHLESS Motor Figure Inch Forward N/A Remove plug buttons from the middle of the base frame Suspension ARM for REMOVING/INSTALLINGWheelchairs with Gearless REMOVING/INSTALLING the 3-INCH ANTI-TIP Assembly Figure ANTI-TIPPER Wheel Replacement FigureRWD 138 Warranty Warranty Canada One Invacare Way