CiM-550 IP Enabled Satellite Modem

 

 

 

 

 

 

 

 

 

Rev. 2

Remote Control

 

 

 

 

 

 

 

 

 

 

 

 

CD/CIM550.IOM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Parameter

 

Command

 

 

Arguments for

 

 

Description of arguments

 

Response to Command

 

Query

 

Response to

 

Type

 

(Instruction

 

 

Command or

 

 

(note that all arguments are ASCII numeric

 

(target to controller)

 

(Instruction

 

query

 

 

 

Code and

 

 

Response to

 

 

codes, that is, ASCII codes between 48 and 57)

 

 

 

Code and

 

(target to

 

 

 

qualifier)

 

 

Query

 

 

 

 

 

 

 

qualifier)

 

controller)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

b defines the IF band, with 1 = 70MHz, 2 =

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

140MHz

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

c defines RX only, with 1 = RX/TX, 2 = RX only.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Example: EID=455011 (CiM-550, Rate 3/4 Turbo

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Codec, 70 MHz band, RX/TX)

 

 

 

 

 

 

 

Faults

 

N/A

 

5 bytes,

 

 

Query only. Unit returns the current fault and status

 

N/A

 

FLT?

FLT=abcde (see

 

and

 

 

 

 

first 3 bytes

 

 

codes for the Unit (hardware), Tx Traffic and Rx

 

 

 

 

 

description for

 

Status

 

 

 

 

alpha-numerical

 

 

Traffic, in the form abcde, where:

 

 

 

 

 

details of

 

 

 

 

 

 

 

a = Unit fault status, b = Tx Traffic status,

 

 

 

 

 

arguments

 

 

 

 

 

 

4th and 5th

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

c = Rx Traffic Status, d = Change in Fault Status

 

 

 

 

 

 

 

 

 

 

 

 

bytes, value of 0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

or 1

 

 

since last poll (0 = none, 1 = change), e = Change

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

in Unit Configuration since last poll (0 = none, 1 =

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

change)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Unit faults:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0

= No faults

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

= Power supply fault, 5 volts

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

= Power supply fault , 12 volts

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

= Power supply fault, -5 volts

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

= Power supply fault, 18 volts

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

= Power supply fault, -12 volts

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

= RAM load fail

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

= Tx synthesiser lock

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

= Rx synthesiser

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

= Power cal Checksum error

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A = FPGA main chain load fail

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B = Turbo FPGA load fail

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C = CiM IP Module Fail

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Tx Traffic status:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0

= Tx traffic OK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

79