CiM-550 IP Enabled Satellite Modem

 

 

 

 

Rev. 2

Remote Control

 

 

 

 

 

 

 

CD/CIM550.IOM

 

 

 

 

 

 

 

 

 

 

Parameter

 

Command

 

Arguments for

Description of arguments

Response to Command

 

Query

Response to

Type

 

(Instruction

 

Command or

(note that all arguments are ASCII numeric

(target to controller)

 

(Instruction

query

 

 

Code and

 

Response to

codes, that is, ASCII codes between 48 and 57)

 

 

Code and

(target to

 

 

qualifier)

 

Query

 

 

 

qualifier)

controller)

 

 

 

 

 

 

 

 

 

 

 

0 = Normal

but invalid argument found)

 

 

argument)

 

 

 

 

 

1 = Rx Spectrum Inverted

RSI* (message ok, but not

 

 

 

 

 

 

 

 

All other codes invalid.

permitted in current mode)

 

 

 

 

 

 

 

 

 

 

 

 

 

Rx

 

RDS=

 

1 byte, value of

Command or Query.

RDS= (message ok)

 

RDS?

RDS=x

Descrambler

 

 

 

0 or 1

Rx De-scrambler state, where:

RDS? (received ok,

 

 

(same format as

 

 

 

 

 

0 = Off

but invalid argument found)

 

 

command

 

 

 

 

 

1 = On (V.35 in unframed mode, synchronous in

RDS* (message ok, but not

 

 

argument)

 

 

 

 

 

framed mode

permitted in current mode)

 

 

 

 

 

 

 

 

All other codes invalid.

 

 

 

 

 

 

 

 

 

Example: RDS=1 (which is de-scrambler On)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Rx Demod

 

RSW=

 

2 bytes,

Command or Query.

RSW= (message ok)

 

RSW?

RSW=xx

Acq Sweep

 

 

 

numerical

Rx ± acquisition sweep range of demodulator, in

RSW? (received ok,

 

 

(same format as

Width

 

 

 

 

kHz, ranging from ± 1 kHz to ± 30 kHz.

but invalid arguments found)

 

 

command

 

 

 

 

 

Example: RSW=09 (which is 9 kHz)

RSW* (message ok, but not

 

 

arguments)

 

 

 

 

 

 

permitted in current mode)

 

 

 

Rx Clock

 

RCK=

 

1 byte, value of

Command or Query.

RCK= (message ok)

 

RCK?

RCK=x

Mode

 

 

 

0 or 1

Rx Clock mode, where:

RCK? (received ok,

 

 

(same format as

 

 

 

 

 

0 = Buffer disabled

but invalid argument found)

 

 

command

 

 

 

 

 

1 = Buffer enabled

RCK* (message ok, but not

 

 

argument)

 

 

 

 

 

All other codes invalid.

permitted in current mode)

 

 

 

 

 

 

 

 

Example: RCK=0 (which is buffer disable)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Eb/No Alarm

 

EBA=

 

4 bytes,

Command or Query.

EBA= (message ok)

 

EBA?

EBA=xx.x

Point

 

 

 

numerical

Eb/No alarm point, with a range of Eb/No between

EBA? (received ok,

 

 

(same format as

 

 

 

 

 

0 and 16 dB. Resolution 0.1 dB.

but invalid arguments found)

 

 

command

 

 

 

 

 

Example: EBA=12.3 (which is Eb/No = 12.3 dB)

 

 

 

arguments)

 

 

 

 

 

 

 

 

 

 

Rx Buffer

 

RBS=

 

1 byte, value of

Command or Query.

RBS= (message ok)

 

RBS?

RBS=x

Size

 

 

 

1,2,3,4 or 5

Rx buffer size, where:

RBS? (received ok,

 

 

(same format as

 

 

 

 

 

 

 

 

 

 

66