8. Programmable Features
89
{2}“Tone” (default): For tone dial service.
Note:
LYou can also program this feature with the
base unit (feature #13 on page 79).
LINE 1:{0}{5}{2}{1} LINE 2:{0}{5}{2}{2}Setting the flash time
The flash time depends on your telephone
exchange or host PBX.
{1} “700ms” (default)
{2} “600ms”
{3} “400ms”
{4} “300ms”
{5} “250ms”
{6} “110ms”
{7} “100ms”
{8} “90ms”
Note:
LThe setting should stay at 700 ms unless
pressing {FLASH/CALL WAIT} fails to pick
up the Call Waiting call.
LIf the unit is connected via a PBX, PBX
functions (transferring a call, etc.) might not
work correctly. Consult your PBX supplier for
the correct setting.
LYou can also program this feature with the
base unit (feature #72* and feature #72# on
page 83).
LINE 1:{0}{5}{3}{1} LINE 2:{0}{5}{3}{2}Setting line mode
The line mode for both lines is preset to “B” and
generally should not be adjusted. If k and
l are not displayed on the handset properly,
or {LINE1} and {LINE2} on the base unit do not
light properly, the line mode selection is
incorrect. Set line mode to “A”.
{1} “A”
{2} “B” (default)
Note:
LYou can also program this feature with the
base unit (feature #62* and feature #62# on
page 82)
{0}{5}{5} Selecting the line for telephone calls (Handset)
To determine which line is selected when you
press {TALK } or {SP-PHONE} for telephone
calls.
{1} “Line1”: LINE1 will be selected.
{2} “Line2”: LINE2 will be selected.
{0} “Auto” (default): When making a call, LINE
1 will be selected. If that line is unavailable, LINE
2 will be selected. When answering a call, the
ringing line will be selected. When you call back
using caller information (page 45), the indicated
line will be selected.
LIf the auto talk feature is turned ON (feature
03 on page 88), the unit will select the ringing
line when you lift the handset OFF the
charger to answer the call.
Note:
LYou can select a line manually regardless of
this setting by pressing {LINE1} (soft key) or
{LINE2} (soft key).
LINE1:{0}{6}{1}{1} LINE2:{0}{6}{1}{2}Changing the ring setting of the telephone
answering machine
To change the number of rings before the unit
answers a call in TAM/FAX mode (page 60) or
TAM ONLY mode (page 61).
{2} “2” (default)
{3} “3”
{4} “4”
{5} “5”
{6} “6”
{7} “7”
{0} “Toll saver”
Note:
LYou can also program this feature with the
base unit (feature #06* and feature #06# on
page 79).
LINE1:{0}{6}{2}{1} LINE2:{0}{6}{2}{2} Changing the maximum recording time for incoming messages
{1} “1min”: 1 minute
{2} “2min”: 2 minutes
{3} “3min” (default): 3 minutes
{0} “Greeting only”: Only plays the greeting
message.
Note:
LIf you select “Greeting only” for the
line(s), the unit will answer a call with the
greeting message, and then hang up. The
unit will not record any incoming messages
for the line(s).
LYou can also program this feature with the
base unit (feature #10* and feature #10# on
page 79).
{0}{6}{3} Setting remote operation code
LEnter a 2-digit number (00–99).
The default setting is “11”.
Note:
LYou can also program this feature with the
base unit (feature #11 on page 79).
FG6550-PFQX2225ZA-en.book Page 89 Monday, August 8, 2005 8:16 PM