Benefits | Pengo Computer Accessories UBR7200 guide

Multipoint Wireless Support for the Cisco uBR7200 Series Universal Broadband Router

Feature Overview

The power feed panel consists of the following components:

•Coaxial cable connection ports to the wireless modem card on the front panel

•Power ON/OFF switches on the front panel, with LED power indicators

•Coaxial cable connection ports to the wireless transverter on the rear panel, with LED power indicators

•DC power supply terminal blocks on the rear panel

At least one power feed panel is required for each installation. Each power feed panel supports a maximum of four wireless transverters.

For further information regarding the power feed panel, including detailed installation information, refer to the Cisco uBR7200 Series Router Multipoint Wireless Modem Card and Subsystem Installation document.

Wireless Transverter

The ruggedized wireless transverter is the outdoor data interface to the indoor subsystems. It provides up/down conversion from IF to RF frequencies.

The wireless transverter consists of the following components:

•RF head

•Connector port for IF input, power, and control signal

•Duplexer assembly with antenna connection

For further information regarding the wireless transverter, including detailed installation information, refer to the Cisco uBR7200 Series Router Multipoint Wireless Modem Card and Subsystem Installation document.

Benefits

The broadband fixed wireless multipoint system provides:

•Fast, easy deployment

•Flexibility—Various interfaces to the host routers and numerous network deployment plans

•End-to-end Cisco IOS network, enabling multiservice security, multimedia, and management support

•Scalable network growth through the addition of more cells or sectors

•Full-duplex data rates of up to 22 Mbps

•Non-line-of-sight (Non-LOS) Vector Orthogonal Frequency Division Multiplexing (VOFDM) technology, enabling greater service coverage

Related Features and Technologies

The point-to-point wireless router system.

Cisco IOS Release 12.1(5)XM

4

Image 4

Pengo Computer Accessories UBR7200 Benefits, Related Features and Technologies, Point-to-point wireless router system

Contents

Feature Overview Multipoint Headend System Cisco uBR7200 series router Multipoint Headend Components Router Point-to-point wireless router system Related Features and TechnologiesBenefits Supported Platforms Supported Standards, MIBs, and RFCsPrerequisites Related Documents Configuration Tasks Multipoint CLI Commands Classification Configuring if Loopback Optional Overriding the Default Microcode PathCommand Purpose Configuring RF Loopback Optional Configuring the Modulation Profile for a Wireless Link Setting the Power Levels and Frequencies Sets the upstream transmit-power to power DBmSets frequency and bandwidth for the downstream Sets the subchannel and modulation-profile Configuring the Automatic Level Control ALC Verifying the Wireless Modem Card Configuration Power ranging configuration information for Displays histogram specificationsOn the wireless modem card and the events related Displays information by service identifier SID Displays quality-of-service QoS profile Configuration information for the profileDisplays information about a wireless modem card Displays the traffic encryption life-time Configuration Examples RF-RF Link ConfigurationDownstream Channel Configuration Upstream Channel Configuration Modulation Profiles Configurations Command Reference Startup Commands Verification Commands Monitoring Commands Troubleshooting Commands Command Description Clear radio flap-listAll ReleaseModification Command Modes Command History Clear radio link-metricsShow interfaces radio Metrics Show interface radio CommandDescription ResetClear radio subscriber counters Clear radio subscriber address all counters Clear radio subscriber reset Router# clear radio subscriber all resetClear radio address all Counter Loopback Defaults Command Modes Command HistorySyntax Description Microcode reload Microcode reload all cwrhe slot slotAll Cwrhe No ping docsis Ping docsisRouter# ping docsis Pppoe enable No pppoe enable Pppoe enableShow interface Usage Guidelines Examples Related Commands Pppoe-forwarding Pppoe forwarding default-qos-level Routerconfig-if#forwarding default-qos-levelEnables PPPoE forwarding on the radio interface Sets a PPPoE forwarding group number on the router Pppoe forwarding group Forwarding group group-num No forwarding group group-numOr PVC interface refer to the PPP over Ethernet document Interface Related Commands Description Defaults Command Modes Command History Examples Pppoe su-mac Enable PPPoE forwarding on the radio interface Quality-of-service QoS-levelRouterconfig# tag UUNet-Gold qoslevel 1 type pppoe Pppoe tag Radio alc Defaults Command Modes Command History Usage GuidelinesSlot/port alc Syntax Description Defaults Following example shows how to activate ARP requestsRouterconfig-if# radio arp Radio arp No radio cable-loss Radio cable-lossRelease Modification Installation CommandRunning-configuration Interface radio Feed Panel Lightning Supression To Transverter Configured Radio downstream annex BRadio downstream annex B No radio downstream annex B Usage Guidelines Examples Radio downstream frequency Width Been configured Displays the allowed ranges of frequency Weighted-discard Examples Usage Guidelines Related CommandsRadio downstream rate-limit Token-bucket No default behavior or values Interface configuration Radio downstream subchannel modulation-profile Router# radio downstream subchannel 1 modulation-profile Radio flap-list aging days no radio flap-list aging Radio flap-list agingClear radio flap-list Displays the radio flap list of a wireless modem card Routerconfig# radio flap-list insertion-timeRadio flap-list insertion-time Subscriber unit in the flap-list table Following example shows how to set the miss threshold to CMTS01config# radio flap-list miss-thresholdRadio flap-list miss-threshold Sets the radio flap list insertion time Radio flap-list size Radio flap-list size sizeNo radio flap-list Following example specifies the flap-list size to Radio helper-address SubscriberHost From hosts Radio hist-display Related Commands Description Radio histogram Average Number toneValSum Width coarse fine Displays radio histograms UBR04config-if#radio histogram sinr-ant1Clears histogram data Radio insertion-interval Routerconfig-if#radio insertion-intervalAutomatic Radio interface radio hist-clear Router# radio int r6/0 hist-clear sinr-ant1 Slot/port hist-start Slot/port hist-stop Channel Radio interface radio hist-startRouter# radio int r6/0 hist-start sinr-ant Slot/port hist-clear Radio interface radio hist-stop Router# radio int r6/0 hist-stop sinr-ant Radio interface radio Clears the histogram data Radio interface radio rf-update duplexer Command Modes Command History Release Modification 12.13XQ1 This command was introduced Syntax Description Defaults Command Modes Command History No default behavior or values Privileged ExecRadio interface radio tl-clear Router# radio int r 6/0 tl-clear sinr-ant1 Slot/port tl-start Slot/port tl-stop Radio interface radio tl-start Router# radio int r 6/0 tl-start sinr-ant1 Slot/port hist-clear Radio interface radio tl-stop Router# radio int r 6/0 tl-stop sinr-ant1 Slot/port tl-start Following example shows how to enable IP broadcast echo Routerconfig-if#radio ip-broadcast echoRadio ip-broadcast-echo Radio ip-broadcast-echo No radio ip-broadcast-echo Radio ip-multicast-echo Routerconfig-if# radio ip-multicast-echoRadio ip-multicast-echo No radio ip-multicast-echo UBR04config-if#radio metrics-threshold-channel 1hour 2 Radio metrics-threshold-channel Show interfaces radio slot/port Metrics-threshold-channel Show interfaces radio slot/port1sec-metrics-channel 1min-metrics-channel Radio metrics-threshold-su Threshold crossed listMetrics-threshold-bad-su Show interfaces radio Displays the metrics for the subscriber unit Radio modulation-profile Bandwidth bandwithThroughput throughput Multipath-robustness Radio privacy kek grace-time 604,800 seconds Interface configuration Radio privacy kek life-timeSets the radio privacy KEK grace-time Life-time Wireless subscriber units Routerconfig-if#radio privacy mandatoryRadio privacy mandatory Radio privacy mandatory No radio privacy mandatory UBRconfig-if#radio privacy tek grace-time Radio privacy tek grace-time 43,200 seconds Interface configuration 12-23T This command was introducedUBRconfig-if#radio privacy tek life-time Radio privacy tek life-time Radio proxy-arp Radio proxy-arp No radio proxy-arp Update Radio qos permissionCreate Enforce Radio qos profile Routerconfig# radio qos profile 4 guaranteed-upstream Routerconfig# radio qos profile 4 max-burstRouterconfig# radio qos profile 4 max-downstream Routerconfig# radio qos profile 4 priority Radio ra-backoff Radio ra-backoff No radio ra-backoff Show running-configuration Radio receive-antennasRadio receive-antennas 1 2 no radio receive-antennas Interfaces radio Radio relay-agent-option Routerconfig-if#radio relay-agent-optionRadio relay-agent-option No radio relay-agent-option Radio rf-meas-interval ambient Radio rf-meas-intervalSets the measurement interval of a calibrated noise source Calibration Show interface Routerconfig-if#radio rf-meas-interval calibration Radio rf-meas-interval calibrationTaken Ambient Enable Self-test is disabled by default Interface configurationRadio self-test Radio self-test no radio self-test Radio shared-secret 0 7 authen-keyno radio shared-secret Radio shared-secretNo radio shared-secret Initial-ranging maint-range sm-datara power null Radio snapshotNo radio snapshot dspNum Short-data long-data inr-data cable-pad Power Maint-rangeSm-data Null Related Commands Description UBRconfig-if# radio source-verify Radio source-verifyRadio source-verify No radio source-verify Following example activates upstream verification Radio threshold Routerconfig-if#radio threshold sinr-ant1 0 high Dsp Radio timeline Print-options On or offHigh-thresh low-thresh up-change down-change Pos-crossing neg-crossing Radio interface radio tl-stop command is entered Down-changePos-crossing Neg-crossing 100 Radio transmit-power Radio transmit-power power-level No radio transmit-powerUBR04config-if#radio transmit-power 101 Disabled Interface configuration Routerconfig-if#radio upstream 4 admission-controlRadio upstream admission-control 102 UBRconfig-if#radio upstream 2 data-backoff 2 Radio upstream data-backoffAuto Respectively, for upstream port Radio upstream description 104 Radio upstream frequency UBRconfig-if#interface radio 6/0 radio upstream 0 frequency105 106 Radio upstream range-backoff UBRconfig-if#radio upstream 2 range-backoff 2107 Routerconfig-if#radio upstream 4 rate-limit token-bucket Radio upstream rate-limitToken-bucket Shaping Routerconfig-if#radio upstream 2 shutdown Radio upstream shutdownSubscriber unit to the headend 109 Modulation-profile Radio upstream subchannel110 111 UBR04config-if#radio upstream 1 target-receive-power Radio upstream target-receive-power112 Show controllers radio 113 Parameters depend on the hardware and implementation Sid114 Router# show controllers radio Show controllers radio downstream Number115 Router# show controllers radio 3/0 downstream Show controllers radio if 116 117 UBR04# show controllers 3/0 radio if Show controllers radio rf 118 119 UBR04# show controllers 3/0 radio rf 120 Show controllers radio upstreamCMTS01# show controllers radio 3/0 0 upstream Show interfaces radio metrics 121 Slot, 6 port 0 of the Cisco uBR7200 series router 122Router# show interfaces radio 6/0 metrics-su 0000.0acd.8933 Router# show int radio r6/0 metrics-bad-su 123 Router# show interfaces radio 6/0 1hour-metrics-channel Show interface radio accounting Show interface radio slot/downstream-portaccountingModem card in slot 6, port 124 Wireless modem card in slot 5, port Show interface radio alcShow interface radio slot/downstream-portalc 125 Show interface radio downstream Show interface radio slot/downstream-portdownstream126 UBR# show interface radio 6/0 downstream Show interface radio hist-data Card in slot 6, port127 Router# show int r6/0 hist-data sinr-ant Show interface radio Displays histogram specifications 128 Show interface radio hist-spec Radio card in slot 6, portShow interface radio Displays histogram data Slot/port hist-data Show interface radio led Major-eventsMinor-events LEDs Function Router# show int radio 6/0 led 131LED Name Status Show interface radio ranging Show interface radio slot/port rangingSlot 132 Show interface radio rf-meas-interval Show interface slot/dsport rf-meas-interval133 Router# show interface r3/0 rf-meas-interval Show interface radio sid CountersVerbose Connectivity Show interface radio snap-data 135 Creates a snapshot specification Displays snapshot specification informationCard in slot 3, port 136 Displays data captured for the snapshot specification Show interface radio snap-specShow interface radio slot/port snap-spec dspNum Modem card in slot 3, port Configures a threshold specification Show interface radio thresholdsShow interface radio slot/port thresholds Port 0 for the Receive DSP 1b 139 Show interface radio tl-dataRouter# show int radio 6/0 tl-data sinr-ant1 140 Show interface radio tl-spec Port141 Router# show int radio 6/0 tl-spec 142 Show interface radio upstream Show interface radio slot/upstream-portupstream143 Radio 6/0 upstream Show interface radio zero-burst Show interface radio slot/port zero-burst144 UBR7200# show interface radio 5/0 zero-burst Show radio capability modulation-profile 145 146 Upstream Show radio device access-group Access-groupShow radio device 147 Show radio errors 148 Show radio flap-list Show radio flap-list sort-flap sort-time Sort-flapFlapped Sort-time Statistic Description 150 Troubleshooting. The CRC counter indicates Intermittent upstreamImpulsive noise or interference 151 152 Show radio modulation-profile 153 154 Show radio privacy kekCMTS01# show radio privacy kek 155 Show radio privacy tek Kek156 CMTS01# show radio privacy tek Following example shows how to display a QoS profile table Radio qos profile Configures the QoS profileShow radio qos profile Show radio qos profile number verbose Show radio subscriber 158 Service identifier assigned to a modem Field DescriptionNumber of customer premises equipment devices PCs Macintoshes, Unix workstations, and so on behind this radio 160 161 Debug Commands 162 Defaults Command History Following example shows how to display ARP requestsDebug docsis arp Debug docsis arp No debug docsis arp Debug docsis err Debug docsis err No debug docsis err164 Router# debug docsis err Debug docsis keyman Debug docsis keyman No debug docsis keymanActivity 165 Debug docsis mac Debug docsis mac log messages no debug docsis macLog Messages Following example shows how to display Docsis maps Debug docsis mapDebug docsis map No debug docsis map 167 This command has no arguments or keywords Debug docsis privacyDebug docsis privacy no debug docsis privacy 168 Debug docsis qos Debug docsis qos no debug docsis qos169 Router# debug docsis qos Debug docsis range Debug docsis range no debug docsis range170 Router# debug docsis range Debug docsis receive Debug docsis receive No debug docsis receive171 Router# debug docsis receive Debug docsis reg Debug docsis reg no debug docsis reg172 Router# debug docsis reg Debug docsis reset Debug docsis reset no debug docsis resetFollowing example shows how to display debug reset messages Router# debug docsis reset Debug docsis startalloc Debug docsis startalloc No debug docsis startallocAllocated to subscribers 174 Debug docsis transmit Debug docsis transmit No debug docsis transmitRouter across the network 175 Debug docsis ucc Debug docsis ucc no debug docsis uccRequests are assigned a new channel 176 Following example shows how to display UCD messages Debug docsis ucdDebug docsis ucd no debug docsis ucd UBR7200 series console Debug radio p2mp alc Debug radio p2mp alc No debug radio p2mp alcInterfaces 178 This command has not arguments or keywords Debug radio p2mp phy cwrlog radio179 Router# debug radio p2mp phy cwrlog radio Glossary 180