120 | Pengo Computer Accessories UBR7200 manual

Multipoint Wireless Support for the Cisco uBR7200 Series Universal Broadband Router

show controllers radio upstream

show controllers radio upstream

To display upstream port information for a wireless modem card, use the show controllers radio upstream EXEC command. To disable this function, use the no form of this command.

show controllers radio slot/upstream-portupstream

no show controller radio slot/upstream-portupstream

Syntax Description		slot/upstream-port	Specifies the slot and upstream port numbers of the wireless modem card.

Defaults		No default behavior or values.

Command Modes

Command History

EXEC

ReleaseModification

12.1(3)XQ1	This command was introduced.

Examples	The following example shows how to display information for upstream 0 in slot number 3, port number
	0:
	CMTS01# show controllers radio 3/0 0 upstream
	Radio 3/0 Upstream 0 is up

Frequency 5.008 MHz, Channel Width 0.200 MHz, QPSK Symbol Rate 0.160 Msps Spectrum Group 4

Nominal Input Power Level 5 dBmV, Tx Timing Offset 0

Ranging Backoff Start 16, Ranging Backoff End 16, Tx Backoff Start 16 Tx Backoff End 16, Modulation Profile Group 1

part_id=0x3137, rev_id=0x01, rev2_id=0xFF nb_agc_thr=0x0000, nb_agc_nom=0x0000 Range Load Reg Size=0x58

Request Load Reg Size=0x0E

Minislot Size in number of Timebase Ticks is = 8 Minislot Size in Symbols =8

Bandwidth Requests = 0x0

Piggyback Requests = 0x0

Invalid BW Requests= 0x0

Minislots Requested= 0x0

Minislots Granted = 0x0 Minislot Size in Bytes = 2 UCD Count = 0

DES Ctrl Reg#0 = C00C0C43, Reg#1 = 0

Cisco IOS Release 12.1(5)XM

120

Image 120

Pengo Computer Accessories UBR7200 Show controllers radio upstream, 120, CMTS01# show controllers radio 3/0 0 upstream

Contents

Feature Overview Multipoint Headend System Cisco uBR7200 series router Multipoint Headend Components Router Related Features and Technologies Point-to-point wireless router systemBenefits Supported Platforms Supported Standards, MIBs, and RFCsPrerequisites Related Documents Configuration Tasks Multipoint CLI Commands Classification Overriding the Default Microcode Path Configuring if Loopback OptionalCommand Purpose Configuring RF Loopback Optional Configuring the Modulation Profile for a Wireless Link Setting the Power Levels and Frequencies Sets the upstream transmit-power to power DBmSets frequency and bandwidth for the downstream Sets the subchannel and modulation-profile Configuring the Automatic Level Control ALC Verifying the Wireless Modem Card Configuration Power ranging configuration information for Displays histogram specificationsOn the wireless modem card and the events related Displays information by service identifier SID Displays quality-of-service QoS profile Configuration information for the profileDisplays information about a wireless modem card Displays the traffic encryption life-time Configuration Examples RF-RF Link ConfigurationDownstream Channel Configuration Upstream Channel Configuration Modulation Profiles Configurations Command Reference Startup Commands Verification Commands Monitoring Commands Troubleshooting Commands Command Description Clear radio flap-listAll ReleaseModification Command Modes Command History Clear radio link-metricsShow interfaces radio Metrics Show interface radio CommandDescription ResetClear radio subscriber counters Clear radio subscriber address all counters Clear radio subscriber reset Router# clear radio subscriber all resetClear radio address all Counter Defaults Command Modes Command History LoopbackSyntax Description Microcode reload Microcode reload all cwrhe slot slotAll Cwrhe Ping docsis No ping docsisRouter# ping docsis Pppoe enable Pppoe enable No pppoe enableShow interface Usage Guidelines Examples Related Commands Pppoe-forwarding Pppoe forwarding default-qos-level Routerconfig-if#forwarding default-qos-levelEnables PPPoE forwarding on the radio interface Sets a PPPoE forwarding group number on the router Pppoe forwarding group Forwarding group group-num No forwarding group group-numOr PVC interface refer to the PPP over Ethernet document Interface Related Commands Description Defaults Command Modes Command History Examples Pppoe su-mac Enable PPPoE forwarding on the radio interface Quality-of-service QoS-levelRouterconfig# tag UUNet-Gold qoslevel 1 type pppoe Pppoe tag Defaults Command Modes Command History Usage Guidelines Radio alcSlot/port alc Syntax Description Defaults Following example shows how to activate ARP requestsRouterconfig-if# radio arp Radio arp Radio cable-loss No radio cable-lossRelease Modification Installation CommandRunning-configuration Interface radio Feed Panel Lightning Supression To Transverter Configured Radio downstream annex BRadio downstream annex B No radio downstream annex B Usage Guidelines Examples Radio downstream frequency Width Been configured Displays the allowed ranges of frequency Weighted-discard Examples Usage Guidelines Related CommandsRadio downstream rate-limit Token-bucket No default behavior or values Interface configuration Radio downstream subchannel modulation-profile Router# radio downstream subchannel 1 modulation-profile Radio flap-list aging Radio flap-list aging days no radio flap-list agingClear radio flap-list Displays the radio flap list of a wireless modem card Routerconfig# radio flap-list insertion-timeRadio flap-list insertion-time Subscriber unit in the flap-list table Following example shows how to set the miss threshold to CMTS01config# radio flap-list miss-thresholdRadio flap-list miss-threshold Sets the radio flap list insertion time Radio flap-list size Radio flap-list size sizeNo radio flap-list Following example specifies the flap-list size to Radio helper-address SubscriberHost From hosts Radio hist-display Related Commands Description Radio histogram Average Number toneValSum Width coarse fine UBR04config-if#radio histogram sinr-ant1 Displays radio histogramsClears histogram data Routerconfig-if#radio insertion-interval Radio insertion-intervalAutomatic Radio interface radio hist-clear Router# radio int r6/0 hist-clear sinr-ant1 Slot/port hist-start Slot/port hist-stop Radio interface radio hist-start ChannelRouter# radio int r6/0 hist-start sinr-ant Slot/port hist-clear Radio interface radio hist-stop Router# radio int r6/0 hist-stop sinr-ant Radio interface radio Clears the histogram data Radio interface radio rf-update duplexer Command Modes Command History Release Modification 12.13XQ1 This command was introduced Syntax Description Defaults Command Modes Command History No default behavior or values Privileged ExecRadio interface radio tl-clear Router# radio int r 6/0 tl-clear sinr-ant1 Slot/port tl-start Slot/port tl-stop Radio interface radio tl-start Router# radio int r 6/0 tl-start sinr-ant1 Slot/port hist-clear Radio interface radio tl-stop Router# radio int r 6/0 tl-stop sinr-ant1 Slot/port tl-start Following example shows how to enable IP broadcast echo Routerconfig-if#radio ip-broadcast echoRadio ip-broadcast-echo Radio ip-broadcast-echo No radio ip-broadcast-echo Routerconfig-if# radio ip-multicast-echo Radio ip-multicast-echoRadio ip-multicast-echo No radio ip-multicast-echo UBR04config-if#radio metrics-threshold-channel 1hour 2 Radio metrics-threshold-channel Show interfaces radio slot/port Metrics-threshold-channel Show interfaces radio slot/port1sec-metrics-channel 1min-metrics-channel Radio metrics-threshold-su Threshold crossed listMetrics-threshold-bad-su Show interfaces radio Displays the metrics for the subscriber unit Radio modulation-profile Bandwidth bandwithThroughput throughput Multipath-robustness Radio privacy kek grace-time 604,800 seconds Interface configuration Radio privacy kek life-timeSets the radio privacy KEK grace-time Life-time Wireless subscriber units Routerconfig-if#radio privacy mandatoryRadio privacy mandatory Radio privacy mandatory No radio privacy mandatory UBRconfig-if#radio privacy tek grace-time Radio privacy tek grace-time 43,200 seconds Interface configuration 12-23T This command was introducedUBRconfig-if#radio privacy tek life-time Radio privacy tek life-time Radio proxy-arp Radio proxy-arp No radio proxy-arp Update Radio qos permissionCreate Enforce Radio qos profile Routerconfig# radio qos profile 4 guaranteed-upstream Routerconfig# radio qos profile 4 max-burstRouterconfig# radio qos profile 4 max-downstream Routerconfig# radio qos profile 4 priority Radio ra-backoff Radio ra-backoff No radio ra-backoff Show running-configuration Radio receive-antennasRadio receive-antennas 1 2 no radio receive-antennas Interfaces radio Routerconfig-if#radio relay-agent-option Radio relay-agent-optionRadio relay-agent-option No radio relay-agent-option Radio rf-meas-interval ambient Radio rf-meas-intervalSets the measurement interval of a calibrated noise source Calibration Show interface Routerconfig-if#radio rf-meas-interval calibration Radio rf-meas-interval calibrationTaken Ambient Enable Self-test is disabled by default Interface configurationRadio self-test Radio self-test no radio self-test Radio shared-secret Radio shared-secret 0 7 authen-keyno radio shared-secretNo radio shared-secret Initial-ranging maint-range sm-datara power null Radio snapshotNo radio snapshot dspNum Short-data long-data inr-data cable-pad Power Maint-rangeSm-data Null Related Commands Description UBRconfig-if# radio source-verify Radio source-verifyRadio source-verify No radio source-verify Following example activates upstream verification Radio threshold Routerconfig-if#radio threshold sinr-ant1 0 high Dsp Radio timeline Print-options On or offHigh-thresh low-thresh up-change down-change Pos-crossing neg-crossing Radio interface radio tl-stop command is entered Down-changePos-crossing Neg-crossing 100 Radio transmit-power Radio transmit-power power-level No radio transmit-powerUBR04config-if#radio transmit-power 101 Disabled Interface configuration Routerconfig-if#radio upstream 4 admission-controlRadio upstream admission-control 102 UBRconfig-if#radio upstream 2 data-backoff 2 Radio upstream data-backoffAuto Respectively, for upstream port Radio upstream description 104 UBRconfig-if#interface radio 6/0 radio upstream 0 frequency Radio upstream frequency105 106 UBRconfig-if#radio upstream 2 range-backoff 2 Radio upstream range-backoff107 Routerconfig-if#radio upstream 4 rate-limit token-bucket Radio upstream rate-limitToken-bucket Shaping Routerconfig-if#radio upstream 2 shutdown Radio upstream shutdownSubscriber unit to the headend 109 Radio upstream subchannel Modulation-profile110 111 Radio upstream target-receive-power UBR04config-if#radio upstream 1 target-receive-power112 Show controllers radio 113 Parameters depend on the hardware and implementation Sid114 Router# show controllers radio Show controllers radio downstream Number115 Router# show controllers radio 3/0 downstream Show controllers radio if 116 117 UBR04# show controllers 3/0 radio if Show controllers radio rf 118 119 UBR04# show controllers 3/0 radio rf Show controllers radio upstream 120CMTS01# show controllers radio 3/0 0 upstream Show interfaces radio metrics 121 Slot, 6 port 0 of the Cisco uBR7200 series router 122Router# show interfaces radio 6/0 metrics-su 0000.0acd.8933 Router# show int radio r6/0 metrics-bad-su 123 Router# show interfaces radio 6/0 1hour-metrics-channel Show interface radio accounting Show interface radio slot/downstream-portaccountingModem card in slot 6, port 124 Wireless modem card in slot 5, port Show interface radio alcShow interface radio slot/downstream-portalc 125 Show interface radio downstream Show interface radio slot/downstream-portdownstream126 UBR# show interface radio 6/0 downstream Show interface radio hist-data Card in slot 6, port127 Router# show int r6/0 hist-data sinr-ant Show interface radio Displays histogram specifications 128 Show interface radio hist-spec Radio card in slot 6, portShow interface radio Displays histogram data Slot/port hist-data Show interface radio led Major-eventsMinor-events LEDs Function 131 Router# show int radio 6/0 ledLED Name Status Show interface radio ranging Show interface radio slot/port rangingSlot 132 Show interface radio rf-meas-interval Show interface slot/dsport rf-meas-interval133 Router# show interface r3/0 rf-meas-interval Show interface radio sid CountersVerbose Connectivity Show interface radio snap-data 135 Creates a snapshot specification Displays snapshot specification informationCard in slot 3, port 136 Displays data captured for the snapshot specification Show interface radio snap-specShow interface radio slot/port snap-spec dspNum Modem card in slot 3, port Configures a threshold specification Show interface radio thresholdsShow interface radio slot/port thresholds Port 0 for the Receive DSP 1b Show interface radio tl-data 139Router# show int radio 6/0 tl-data sinr-ant1 140 Show interface radio tl-spec Port141 Router# show int radio 6/0 tl-spec 142 Show interface radio upstream Show interface radio slot/upstream-portupstream143 Radio 6/0 upstream Show interface radio zero-burst Show interface radio slot/port zero-burst144 UBR7200# show interface radio 5/0 zero-burst Show radio capability modulation-profile 145 146 Upstream Show radio device access-group Access-groupShow radio device 147 Show radio errors 148 Show radio flap-list Show radio flap-list sort-flap sort-time Sort-flapFlapped Sort-time Statistic Description 150 Troubleshooting. The CRC counter indicates Intermittent upstreamImpulsive noise or interference 151 152 Show radio modulation-profile 153 Show radio privacy kek 154CMTS01# show radio privacy kek 155 Show radio privacy tek Kek156 CMTS01# show radio privacy tek Following example shows how to display a QoS profile table Radio qos profile Configures the QoS profileShow radio qos profile Show radio qos profile number verbose Show radio subscriber 158 Service identifier assigned to a modem Field DescriptionNumber of customer premises equipment devices PCs Macintoshes, Unix workstations, and so on behind this radio 160 161 Debug Commands 162 Defaults Command History Following example shows how to display ARP requestsDebug docsis arp Debug docsis arp No debug docsis arp Debug docsis err Debug docsis err No debug docsis err164 Router# debug docsis err Debug docsis keyman Debug docsis keyman No debug docsis keymanActivity 165 Debug docsis mac Debug docsis mac log messages no debug docsis macLog Messages Following example shows how to display Docsis maps Debug docsis mapDebug docsis map No debug docsis map 167 This command has no arguments or keywords Debug docsis privacyDebug docsis privacy no debug docsis privacy 168 Debug docsis qos Debug docsis qos no debug docsis qos169 Router# debug docsis qos Debug docsis range Debug docsis range no debug docsis range170 Router# debug docsis range Debug docsis receive Debug docsis receive No debug docsis receive171 Router# debug docsis receive Debug docsis reg Debug docsis reg no debug docsis reg172 Router# debug docsis reg Debug docsis reset Debug docsis reset no debug docsis resetFollowing example shows how to display debug reset messages Router# debug docsis reset Debug docsis startalloc Debug docsis startalloc No debug docsis startallocAllocated to subscribers 174 Debug docsis transmit Debug docsis transmit No debug docsis transmitRouter across the network 175 Debug docsis ucc Debug docsis ucc no debug docsis uccRequests are assigned a new channel 176 Following example shows how to display UCD messages Debug docsis ucdDebug docsis ucd no debug docsis ucd UBR7200 series console Debug radio p2mp alc Debug radio p2mp alc No debug radio p2mp alcInterfaces 178 This command has not arguments or keywords Debug radio p2mp phy cwrlog radio179 Router# debug radio p2mp phy cwrlog radio Glossary 180